7910 modeli
This version is WITHOUT hole for humidity sensor. Drybox is designed to be placed on the right side of the enclosure. Article with build instructions:…
Outdoor cover for the popular analog Capacitive Soil Moisture Sensor v2.0 (according to comments, this also fits version 1.2). No soldering changes are required. I just crimped a JST 2.54 mm female connector on the cable. The cable…
Do the exposed PCB's of the Ender 3 Pro push sensors bug you? Me too. That's why I made these. Just pop them on and enjoy.
3D printable wall mount for Philips Hue Motion sensor , give a little bit wider rotation angles, and allows easy battery changes while keeping the mount aligned to the correct direction. Check out all the mount options . The mount is…
Simple and quick print. Prints in-place, no need for any supports. Print it with 4 perimeters and 100% infill, to be a bit stronger/heavier. After printing make sure to work it out a bit manually so it moves freely. Mounting instructions…
This is a mashup of the following two models to be able to mount a D1 mini v3.0 together with a reed sensor onto a BK-G4 gas meter: https://www.printables.com/model/111029-d1-mini-v3-snapcase-low-profile…
For years now I've had a ratty nail going through the magnet to hold my Hue motion sensors in the corner. It not only looks janky, it doesn't stay put very well. Then, I got a 3D printer. i checked out a few models online, but I didn't…
Allow me to introduce you Capacitive Soil Moisture Sensor v1.2 and v2.0 Case (box). I required this sensor in one of the previous projects and create case for it, to make it more secure. Hope you will enjoy it. Print instructions:…
EN: This compact housing is designed for an LD2450 radar sensor with Bluetooth antenna and an ESP8266 Wemos D1 Mini V4. It is based on F-Square's multi sensor design , but is a new development except for the rear ball joint . The radar…
Just a simple DS18B20 Temperature Sensor mount. I printed it with PLA but if you need it in a place that gets hot you better use something that can withstand the temperature. Slide the sensor in from the top or the bottom. It has a tight…
This is a new version of Domino. It's very helpfull for people with reduced vision or blind. Everybody can have fun! You can play following the shapes or just count the lines. The “S” is 1. The “circles” are 2. The “triangle” is 3.. and…
I had limited side room but sufficient vertical room for my 5 head Prusa XL, so I wanted to mount the spools above the printer, however the placement of the side filament sensors made this an awkward arrangement. I made the bracket that…
This mount is used for mounting JSN-SR04T water level ultrasonic sensor on top of the IBC lid.
Adapter that attaches the magnetic PFTE coupler directly to the Prusa Mini filament sensor, no more dangling PFTE tube necessary. This also solves the problem that the filament sensor does not hold the input PFTE tube tightly at all. When…
Toy. Sensory tray for kids. Additionally, I have included the .bgcode file with my two-color print setup, with manual color change, as seen in the photos.
I found an excellent radiation shield model from @ilMitch_97530 . Unfortunately, I don't use Aqara sensors. So I adapted the original holder for the temperature and humidity sensor TP-Link Tapo T310. It was easy because the author also…
This model is not difficult to print, but it is rather difficult to use. First, you need a TTP223 touch sensor (very cheap on Amazon) that will fit nicely in the center of the switch. Then you need to solder a 28awg wire to the sensor in…
Toy. Sensory tray for kids. Choose the model you like best.
the force required to insert filaments through the sidemounted filament sensor didnt agree with me so i reduced the spring compression by 1mm. reducing it more will become problematic for the center filament. integrated filament numbers…
Toy. Sensory tray for kids. This model is capable of being printed with the rainbow color combination or any other color combination you like. I am including the .3mf file, configured with manual color change. The first and last layers…
A Remixed Cover Lens for a Raspberry P1 Camera V2 board with an ArduCam 8MP IMX219 Sensor module (for RPi and Jetson Nano) with a 175deg Wide Angle M12 Lens. I included the Step file for your remix convenience.
The cubes measure 4×4×4 cm. There are 2 pictures on each cube that you can use to stamp into modeling clay or kinetic sand. Inside there are molds for different objects. The cube develops fine motor skills, vocabulary (create stories),…
I modified on (MK3S/MMU2S Modified extruder-idler-mmu2s1 - Solves IR Filament Sensor Issues_by Sneaks) to make the arm sensor longer, and it worked fine when I test it. Give it try !
This should solve the issue, that the filament sensor get stuck in the master spool. Also the Filament changing doesn't get more complicated. You need: PTFETubeMountingBreaket Original PTFE tube of the Prusa Mini 2x M3 nuts 2x M3x8mm…
Mount for SW-420 vibration sensor for magnetic mounting. Mount SW-420 with an M3x6mm screw and M3 bolt. Friction fit magnet into slot. Models sized for either 10mm (10mm diameter, 3mm thickness) or 8mm (8mm diameter, 2.5mm thickness)…
This is a water level sensor holder with a magnetic base, with adjustable height. The sensor itself is supposed to be lowered into a hole of a liquid container. We use it to check for coolant level in a container for a CNC machine when…
The files are made for a MMU3 (here with MK4) Whereas the Chars (I|O, + and -) are changeable Also the used Extruder, here Main (Display 1) = 3, I|O, + and - = 1 Bracket X for place for two additional mosfet (fan and Led strip) There is…
The case includes the Sensirion SCD30 CO2 sensor and an AZ-Delivery NodeMCU V3 board. In the attached FreeCAD file, custom adjustments can be made in the spreadsheet. Wiring details can be found in the images. Programming is done using…
YOU MUST SWAP SOME WIRES FOR THIS TO WORK!!!! THIS FILE USES A CUSTOM FONT: HELVETICA NEUE (similar to prusa font) Install it before opening FILE!! THE MODEL WILL WORK IF YOU CHOOSE TO KEEP THE SPRINGS IN THE SENSORS AND NOT ADD MAGNETS I…
Xiaomi Temperature and Humidity Sensor Holder by RSCtech You can use screw or glue to fix it. It keeps the sensor stable thanks to its design, even upside down. It can be easily removed when replacing the sensor battery.
Mit diesem Druck kann ein Magnetsensor optisch ansprechend an einem Pipersberg G4 Gaszähler befestigt werden. Der Druck enthält eine Mulde im Boden, die mittig über der zweiten Nachkommastelle angeordnet ist. Um den Zähler auszulesen muss…
Attach a SwitchBot Contact Sensor to your Garage door with the use of these 2 brackets.
Original part flipped, notched for gantry support, added a hole for a ty-rap and made a mounting plate for a Creality filament sensor. Just mark the sensor mounting holes, drill them, and insert heat inserts. Or drill small holes and use…
This is a mounting bracket that holds a JSN-SR04T ultrasonic sensor and waterproof DS18B20 temperature sensor for mounting to a 1" square tube. This is part of a project to measure the water level of a creek. The sensor will be extended…
This is a variation of https://www.printables.com/model/1202146-wall-mountable-housing-for-dht-22-sensor for smaller sensors without own housing. See attached pictures for assembling. Please remember to insert the cable into the housing…
I am not sure if the ADXL345 sensor requires proper orientation to calibrate properly. The original orientation had the X axis pointing down the Y-axis. This now has the Y-Axis pointing down the Y-Axis.
Es wird noch im Mai eine neue Version des Filament Umspulers geben. In dieser VErsion ist der Motor und die Sensoren integriert. Das ganze wird sehr viel kompakter sein. https://www.wendelgass.com/3d-druckwerkstatt Diese Anleitung ist…
When printing in a relatively humid location, it is preferable to print directly from filament dryers or dry boxes, keeping the filament enclosed in PTFE tubing all the way to the printer. This filament sensor top for the CoreOne INDX was…
FR : Voici une cale qui permet de monter un capteur de frein magnétique fournis par bafang avec le bbshd (pour freins hydraulique) Tektro AURIGA comp qui était monter sur un vélo Btwin rockrider 520 de 2013/2014. Je l'ai dessiné car les…
About the print This print is part of a larger project I am working on to implement Mycodo into my hydroponic garden. The goal is to have several modules that can connect independently, with ‘break out boxes ’ for different sensors,…
Deutsch (English below) Zubehör für den Optionalen Filament Guide von Prusa. Ein halter für den Temeratur sensor der Enclouse. Er wird einfach auf den Spulenhalter geschoben wo er einrastet. Zur zusätzlichen Fixierung kann er auch mit den…
Bracket for attaching the Aqara motion sensor to the wall or to the included hook that fits on (my) stairwell. There is a recess in the hook for inserting a magnet.
THIRDREALITY has several sensors that are all 2.2" x 2.2" x 0.48" I have several of these THIRDREALITY Zigbee Temperature and Humidity Sensor Lite's and needed a way to mount them without permanently sticking them to a surface. So I made…
Mount for the Zircon StudSensor L50 compatible with IKEA Skadis pegboards. Would like to do a v2 with rounded lower corners, but this is functional.
In this box you can fit the sensory play cubes with pictures , letter and numbers , rollers , and molds (with mechanical or flexible hinges). It works when printed with PLA or PETG, else I didn't try. The door is print-in-place. It can be…
Mit diesem Gehäuse, lässt sich unser Bewegungsmelder Modul 5V, leicht für viele Anwendungen montieren. Die versenkten Befestigungsbohrungen sind für unsere Modul-Befestigungsschrauben M3 geeignet und ermöglichen eine dezente Montage ohne…
Cap for Ring Door/Window Sensor to allow color matching to paint or trim finishes. Prints well with PLA and 25% infill. Remixed from @Tijnoz 's caps origin and magnet-side cover
Parts list: 2 Magnets in 5x3 mm I experimented with smaller magnets but they did not give me consistent results, but the thicker Base fits nice. If anyone wants i can make one for Round Handle Bases, just leave a comment. Assembly…
Simply resized zoltznf's ( https://www.printables.com/social/1970-zoltanf ) version to the gen 2 model to 82mm with to fit the gen 1 sensors. Note: The higher up the door the sensor is placed the quicker the sensor registers as open. So,…
Swimming pool water temperature monitoring needs a sensor whitch musnt be in contact with the water. Threfore you have to use a shaft, where you put sensor probe in. I made one for you. It has stadard outher thred G1/2 and also metric…
Use the HI-LINK LD2410 motion and presence sensor with Wemos D1 min in esphome. I can also use it to measure light, moving distance, still distance, moving energy, still energy, detection distance, and more with home automation. Use PET…
I use the HC-SR04 sensor to measure the distance of a person approaching to turn on or off the light with Home Assistant automation. I use the D1 Mini board.
Replace the original M6 threads on the OV5647 sensor (Arducam/Zerocam) to M7 threads with this casing. Before changing the threads, you need to remove the original M6 lens casing from the OV5647 sensor body. To do this, you can carefully…
A simple and functional stand designed to hold a small temperature and humidity sensor at the perfect viewing angle. The model is split into two pieces to ensure clean printing without any supports — just print both parts, add a small…
Small case for D1-Mini and temperaturesensor D18B20. I use this sensor for my Homeassistant. I made a tight fit for the board. If it won't go into the housing just grab a file and make the board a little smaller.
A wall-mounting bracket for the Ambient Weather Outdoor PM25 (PM2.5), which for some reason ships with screws but no mounting holes. The sensor simply slides in/out of the top for periodic recharging. The bracket uses the side lugs of the…
This sensor mount is designed to connect most Sparkfun Qwiic enbaled sensors/breakout boards to the Experiential Robotics Platform (XRP) Kit by clipping on the sides and connecting to an open Qwiic port. The model is designed to be 3d…
This float is for a tube with an inner diameter of 8 mm. I use it to check whether my water stack is full or not. It is a watertight box with an inlet, an outlet and a reed float contact. There are gaskets for inlet and reed contact. The…
This model is for the Aqara Door & Window Sensor (affiliate link), and helps you level the two pieces inline with any door or window trim. My door has a ½ inch trim that frames it, and makes it not possible to keep the two pieces of the…
Here's an easy to print play-dough toy waffle maker press that makes heart shaped waffles. These play waffles are suitable for use in the toy waffle iron that you can find elsewhere on printables. Children love pushing down on the top…
Die Dose ,welche über einen Bayonette-Verschluss verfügt, besitzt eine Aussparung, die genau auf den USB-Stick angepasst ist. Das Loch im Deckel und in der Dose sind für eine Schnur gedacht, sodass der Deckel nicht verloren wird. Viel…
XRP Sensor/Display Tower Originally designed to mount Sparkfun Qwiic 1.3" OLED and the ENS160 Environmental Sensor, this mounting tower, can be adapted to any standard sized Sparkfun Qwiic sensor and/or display. The mounting tower snaps…
This clip will hold the DS18B20 temperature probe 90° turned on a 3030 extrusion.
Gedruckt in PLA (0,2mm Speed Profil auf einem MK3S) mit 15% Infill. Benötigt eine Verlängerung des Anschlusses von der Mitte des Druckers zur linken Seite. Verbinder zum Teflon-Schlauch ist ein PC4-M10 Pneumatikverbinder (Bohrung 9mm).
BASETech is a common remote sensor for weather stations. They are sold as Basetech WS-9130-IT, TFA Dostmann 30.3147.IT, Techno Line TX 35-IT and more brands. Although it should be able to survive on its own, a casing might prevent…
Bee comb This sensory game with a bee hive promotes fine motor skills when scooping and pouring rice, lentils, or other materials. It develops awareness of differences between materials and helps children learn to sort, count, and compare…
Temperature and humidity sensor holder with a stand. Designed to be used alone or with LEGO Minifig Hexagons . Printer configuration: 3D Printer: Elegoo Neptune 3 Pro Filament: eSUN PLA+ White Slicer: UltiMaker Cura Resolution: 0.2mm…
Printed in PETG with 100% Perimeters edit: added a thicker v2 since the first one broke after one year of usage
I printed the prototype with PETG.
Adapter allowing you to turn any UP Sensor into a leak detector. Materials: Qty 2, M3x6, Hex Head Bolt Print Settings: No Supports 0.25mm Layer Height NOTE: Use bolt with flat head to ensure contact with pins on UP sensor, see product…
A simple storage rack to take up to 5 Axivity Sensors. The micro-usb port of each sensor is accessible through a hole. Can be printed without supports when the model is sliced with it's backside on the print sheet.
I got tired of my smart home sensor falling of the wall, so I designed my own wall-mount. I will add more pictures (and maybe drill-holes) after the first prototype print is ready.
Adapter for indoor motion sensor I designed this adapter for an indoor motion sensor from HOFTRONIC™. It can be mounted directly to the ceiling junction box U86 from Spelsberg. Optional two cable channels with 15mm will cover the wires to…
This print can be used to connect a Swytch e-bike pedal sensor to a frame with a 28.8mm diameter bar near the pedals. You probably don't need this to mount the sensor to your bike , the included hardware on the pedal sensor is pretty…
If you are a developer, and you don't want to hide the proximity sensor with your hand then this extension is for you! Here are the assembly instructions:
This system leverages the MQ-9 gas sensor (Carbon Monoxide (CO), Methane, LPG detection) and an ESP8266 D1 Mini microcontroller to create a smart gas detection system integrated into Home Assistant (HA) . 🔌 Hardware Connection The MQ-9…
Story: We needed to insert different water level sensors into a DN 110 KG PVC pipe (see sensor-holder-for-kg-pvc-pipe ) and wanted to organise but also protect them. Thats why I have designed a lid which covers most of the top of the pipe…
I had an issue of 1) tape coming off from the rain, and 2) the sensor getting ruined from the rain. So this model already helped with the first issue but not the 2nd, so I added a block to do just that. Happy Printing!!
Achtung : Hier geht um arbeiten am 230 V Netz. Diese Anleitung ist nur für Personen gedacht, die ihre Handlungen selbst beurteilen und verantworten können. Arbeiten an elektrischen Geräten und Installationen können gefährlich sein und…
just a quick (but fit) enclosure for the movement sensor by Sonoff, if you want to put it somewhere outdoor (like me), ie: i want to put it in my mailbox to check whenever new mail arrives, and i wanted to make it a little more wheater…
Story: We needed to insert a water level sensor into a DN 110 KG PVC pipe for a project. Therefore, I have designed a holder that can hold such a sensor and perfectly aligns with the inner shape of the pipe. You need to drill a hole…
Outdoor holder for GETI GMD01 motion sensor. Includes cutout for zip ties. Rainproof with drainage channels.
Structure Sensor ST01 Bracket for iPad (8th gen) - 2020 Design based from the original one for the IPad Air (3rd gen) The distance between the center of Structure sensor camera and the iPad camera 4 cm. This model require: 2X brass M4…
As requested the twist ball fidget available for everyone to download free Features a choice of 2 sensory twist ball fidgets, the low poly version or the soft point version, simply choose your favourite and print The sensory twist ball is…
This version of the spool holder is WITH hole for humidity sensor. Drybox is designed to be placed on the right side of the enclosure. Blog article: Drybox build instructions .
Use normal supports on build plate only. A compact twisty sensory fidget sphere with a spiky textured surface. The sphere is built from rotating segments that can slide and twist along the central axis, creating a satisfying mechanical…
Spiky Sensory Trigger Twisty Spiral Roller This Spiky Spiral Fidget Roller is engineered for dynamic sensory play, featuring tightly patterned geometric spikes that wrap around a twisting core. As it rolls, extends, and shifts in length,…
This was made for use with the DIY enclosure available here . HEADS UP - 1 of 3 - new better version of this! I've published a new, improved remix of my popular side-mounted spool holder — PLEASE NOTE: it's not just about the four…
This plate allows you to mount the Filament runout sensor on the right hand side of the Creality K1 making it easier to use a filament roll on the side of the printer instead of the rear. This plate uses the two screws that secure the…
Remake of the Creality Vibration Sensor for the E3 V3 KE Printed in PLA
A word of caution This project is currently unmaintained, as ESPHome keeps introducing new breaking changes with every monthly update that require continuous rework, testing and debugging. This has been an issue from the very first…
Article with build instructions: https://blog.prusaprinters.org/dryboxes-and-alternative-spool-holders-not-only-for-multimaterial-upgrade/ Material: Prusament PLA Galaxy Black
Yes, it's another infinity cube. But this time with a twist! I wanted to experiment with different designs/textures for the cubes. The file: Textured_Infinity_Cube_v2.stl is a sampling of all 8 styles. Then each style has its own infinity…
" Anycubic Key " 2 Tools in One Extruder Tension disengage tool & Proximity Sensor height tool. Disengage tool allows you to disengage extruder tensioner. Gives you the ability when you load your filament all the way without having to…
Next remix of Drybox for Prusa Printer Enclosure V2 - with humidity sensor. Print instructions You can place five pieces of this drybox on the top of the Prusa Printer Enclosure V2. Can be used as a standalone spool holder for Original…
Update 16.03.2024: A new version (V3) is now available and got slightly changes to fit better into the extrusion. Feedback very much appreciated! Update 02/2024: V2 is now available. This version contains filament clips on both sides! See…
FAQ Q: I printed your enclosure and I can’t figure out how to install the filament sensor / spool holder. I’ve looked on YouTube for installation videos and still stuck. Any help would be greatly appreciated. A: Not long after the initial…
![Radiation Shield for TP-Link Tapo T310 Sensor [Remix] [Update]](https://media.printables.com/media/prints/455919/images/3780277_097a7147-9ad7-4712-9ca0-bcdb72af705a/img_20230423_122418783.jpg)
