Liczymy pasujące modele…
This is a case for the Raspberry Pi Compute Module 4 IO Board. I designed it to be easily 3D printable. The one part that needs support is the overhang by the USB ports. Just paint on some tree supports. My supports came off super easily.…
This is a redesigned case based on Malolo's RPi4 Case. This was designed to fit the WaveShare CM4 IO board with PI 4 Compute Module. The case has a 40mm fan design to blow air across the top then around the side and to the bottom to cool…
Cooling Hood BigtreeTech Manta M8P v1.1 and v2.0 For CB1/CM4 with 60x60x15 Fan M8P. drivers with 5015 Blowerfan. And ziptie mountingpoints for esay wire wireing.
A small case to enclose a raspberry pi compute module with a waveshare nano b board with space to allow for a heat sink. EDIT: Requested, nano A has been added. I do not have the board myself, so feedback welcomed. The idea was to be…
This is a case for the CM 4 on a Nanobase B Carrier Board with mounted heastink. Components: Raspberry Pi CM 4 : Any variant will do Nano Base Board B : Link to Manufacturers site. Got mine from Amazon CM 4 Heatsink B : Also link to…
WaveShare makes a really attractive and very compact base board for the Raspberry Pi Compute Module 4 (CM4). Unfortunately, when I bought mine, there were no suitable enclosures available. This model addresses that shortcoming. This is a…
Print Settings First Layer Height: 0.25mm Layer Height: 0.2mm Extrusion Width: 0.4mm, forced Infill Percentage: 40% Infill Type: Adative Cubic, Grid, Gyroid, Honeycomb, Triangle, Cubic Wall Count: 4 Solid Top/Bottom Layers: 4 Seam…
This is a way to mount a 40mm fan to a Raspberry Pi CM4. The fan mounting holes are sized for M3 heat set inserts, but they're overkill for this project and are easily changed in the included SCAD file. The heat sink I'm using is this one…
WiP Case for Raspberry PI CM4 + Nano Base C + Waveshare Heatsink
Boitier pour waveshare cm4 io base C avec ou sans ventilateur. Face séparée du boitier. En deux version :1° sans ventillateur 2° avec ventillateur. Case for waveshare cm4 io base C with or without fan. Separate side of the case. In two…
This tray/caddy will hold the Raspberry Pi Compute Module 4 IO Board. The design minimizes material, at the expense of leaving some traces & components open on the bottom. Use 4×M2.5 threaded inserts, such as…
I remixed the Design by NotaBrick by simply removing the openings for the GPIO and the Ribbon-Cable-Connectors since i didnt needed them for my project.
There hasn't been much of anything available for these due to the chip shortage for the last year or so, but now that CM4s are trickling out into the wild I thought I'd pick one up and finally finish my router board build. No supports,…
This multi-level box can be printed in a single print. You will need the base and top. Other levels accommodate a portable USB3.2 SSD (Samsung Portable SSD T7) and a multi port USB 3.2 Gen1 HUB HAT. All ports (CSI/DSI/Dual ETH) have…
1U 19 inch rack front panel mount for one 176mm wide switch, one raspberry pi CM4 (with oled display), two 4-port unpowered USB-hubs
!!!Can not Be Used with SD Card, use internal Flash or M.2 on the Back as Boot device, Remix encouraged!!! Case for the following IO Board: https://www.waveshare.com/cm4-io-base-c.htm Needed Hardware: 4 M3x6 Socket head Screw(Or similar)…
Raspberry Pi 4 are hard to source. Using Raspberry CM4 modules together with a cheap baseboard can be a performant and compatible alternative. The CM4-Nano baseboards are sub 20 euro, so they fit well. This is a relatively simple mount…
This minimalist stand is easy to print and lifts your IO Board off the table surface, avoiding damaging your board. Included in the design: 2 Support Plates Models - each model fits a specific side of the IO Board 1 Side Feet Model - feet…
Remix of original great case. Just wanted access to more of the ports.
I haven't found a suitable 10" rack mount for Raspberry Pi CM4 IO Board, so decided to try model it by myself. This remix reuses front plate and honeycomb bottom from original. I printed it using PLA 0.20mm layers without any support. As…
When putting heatsinks onto my CM4 compute modules, there's a 1.5mm gap between the CM4 and the carrier board. This makes it hard to tighten down screws in a way that made me feel comfortable they wouldn't fall off. This is a stupidly…
Case for the "official" (raspberry branded) IO board for the Raspberry Pi CM4 (Compute Module 4) Comes in two version: one with a PCI-e NVME slot (for horizontal NVME adapter) one without it nb: the short side (where the ports are) might…
I wanted a case for my Waveshare CM4-DISP-BASE-5A touchscreen that would present the screen at a better angle. Carl-C's case is a great fit for the screen, but it's missing a back and legs. This remix adds a back plate with reversible…
To assemble the case, you will need: Four M2.5x10 standoffs Four or eight M2.5x6 screws (optional) Four 1.6mm spacers between the CM4 and the router board Print settings: Material: PETG Layer height: 0.2mm Walls loops: 3 Top/bottom…
I bought the reRouter CM4 from Seeed Studio, but the case was out of stock, so I designed my own. This particular board can get pretty hot, so I added a 30mm fan slot to the side of the case and some holes close to where the CM4 should…
Simple fan mount for Raspberry Pi Compute Module 4 (CM4). Fan is a noctua NF-A4x10 40mmx10mm. Requires no additional hardware, just snaps in. Has clearance for a low profile heatsink.
Intended to fit the WaveShare CM4 IO board with Raspberry Pi 4 Compute Module, a redesign to allow for access to the GPIO connector. The case has a 40mm fan design to blow air across the top then around the side and to the bottom to cool…
Updated tray, that doesn't require threaded inserts. Use just direct M2.5x8mm screws. Remake of original model by Jelper.
A simple way to add tabs to unused Raspberry Pi Compute Module 4 (CM4). You can use it to add labels or model number. It also protects the bottom contacts during storage. The M2.5 screw in the photo is not really needed and the CM4 snaps…
Notes: This design is made using FreeCAD The case is designed to maximize convection around the carrier PCB. By design, there are no screws inside the case. Consequently, the insert and the IO Carrier can dislodge if dropped. Before…
Raspberry case for Waveshare CM4-IO-BASE-A module. It is possible to mount two different raspi cam modules on top of the cm4 and to use a fan and a external antenna. For modification a freecad file is provided. You can choose between two…
Obudowa pod Raspberry Pi CM4 i oficjalną płytę CM4IO. W obudowie można zamontować 2-4 dyski 2,5" (zalecam SSD) oraz kontroler PCI-e x1 z 2 lub 4 portami SATA. Ułożenie dysków jest zrobione w taki sposób aby obudowa była jak najprostsza w…
This is a fan bracket for the Raspberry Pi Compute Module 4. It holds a 40mm Fan and was specifically designed for a 5v Noctua fan. However if you use the Fusion 360 file you can adjust the pole height en diameter via the parameter…
Case for https://diodes-delight.com/products/piunora/ used M2x6 screws (4 of them) Printed without supports remixed from https://www.thingiverse.com/thing:994827 Added spy cam case: https://www.adafruit.com/product/5389…
In order to have a Linux driven Touch-Device, which is Battery driven and last for +5 Hours while running a PyQt6 App, I designed this Device. Not exactly the cheapest alternative, but fully customizable. BoM (Bill of Material) attached…
The tolerances are very tight. You may need to file out the inner circle of the mount for the antenna to fit in, and it will need more than hand force to pop it into the skirts. I recommend pliers. I designed this around the Salad Fork…
Remix of model by https://www.printables.com/@Spencers_Desk_520699 A large RPi CM4 Case with lid with 4 SMA Holes Case for TimeBeat Timebeat Mini PTP/GNSS Card. I added depth so you can connect the antennas and holes to mount them. Follow…
This custom 3D printed lid is for a Waveshare metal case base that houses a Raspberry Pi IO Board with a CM4 installed. The Waveshare metal case is a useful reasonably priced ‘ready to use’ component since it comes with a cooling fan as…
I made this antenna mount for my printer after a few days of it banging around inside the wiring cabinet. I did consider mounting the antenna underneath and also inside the inverted wiring cabinet but I didn't want to forget it was…
The enclosure is designed to avoid any screws. A waveshare board should snap into the case . To remove the board you have to softly push RJ45 ports up. The lid also snaps to the case . You might need nails 💅 to open it back (depends on…
Retro Lite CM4: Raspberry Pi Handheld Link to official Source: GitHub - StonedEdge/Retro-Lite-CM4: A CM4 gaming handheld, designed with the Switch Lite aesthetics in mind. Contains all STL files and code to build your own landscape retro…
BOM 2.5 mm bolts 16mm x 4 6mm x 2 2.5mm nuts (x2) are optional 10 or 11 mm rubber feet x 4 (optional) Assembly: print 3 parts mount heatsink onto CB1/CM4, and then CB1/CM4 onto Pi adapter mount Pi adapter w / heatsink into the mid part…
I needed a case for the New Waveshare CM4-DISP-BASE-5A but I couldn't find one anywhere as it was that new when I got it a few months back. I designed it so that the display fits snugly into the case as the screen isn't that thick. It…
A fully-enclosed housing for the Cytron CM4 Maker Board . This uses M3 heat-set nuts to attach the pieces together. Ingredients 8x M3x6 screws 8x M3 heat-set nuts This design is intended to be fully enclosed for dust ingress protection,…
Wanted a nice clean solution for mounting an actual antenna for the CM4 on my Micron. Originally had a skirt mounted solution but it had two flaws: 1. Only worked with Micron R0 skirts 2. Every now and then the antenna would get snagged…
Files to build the case for the DFRobot Raspberry Pi Compute Module 4 IoT Router Carrier Board Mini (see: https://www.dfrobot.com/product-2242.html ). I reviewed this routerboard in May 2021 (…
This case is designed to mount the CM4 IO board (POE) with access to all IO slots, including the SD card. The lid can mount a 40mmx40mmx10mm fan directly above the CM4 with clearance for a heatsink to provide optimal cooling for heavier…
BigTreeTech SKR Pico and Waveshare cm4-nano-b mount to fit into the TwoTrees Sapphire PRO SP3. Should fit in the SP5 as well. The alignment of the Waveshare cm4-nano-b carriercase may look unintuitive, but it is required for the air…
2U 19 inch rack vertical front panel mount for raspberry pi compute module CM4 and oled display These panel mounts require the DAP 2U MP-1 bracket. parts used: Raspberry Pi Compute Module 4 Compute Module 4 Base Board Heatsink 128x32…
This is a case for DFRobots Raspberry Pi Compute Module 4 IoT Router Carrier Board Mini split into two parts; top and bottom. The case is held together without using any screws. Link to dfrobot website:…
This Model is only the bottom case. The top case can be found in the original model and requires no alterations. I reworked the original base to fit the waveshare PoE boat (tested with Rev3). Print Settings Same as the original (3 walls,…
A 10-inch Rack Mount for the Seeed Studio reRouter carrier board for the Raspberry Pi Compute Module 4 (CM4). You can optionally mount up to two SSDs to it. This particular board can get pretty hot, so I added a heatsink and some holes…
1U 19 inch rack front panel mount for one 218mm wide switch, one raspberry pi CM4 (with oled display), two 4-port unpowered USB-hubs
Rear panel for North Pi and Orange Pi CM4 base board.
Remix to make the DFRobot iot router case rack mountable, also added cutout for wireless antenna
The WaveShare CM4-IO-POE-BOX-B is one of my favorite ways of deploying a Raspberry Pi and it already comes with a lot of the I/O options that I frequently need. It even accommodates some Raspberry Pi hats. But if you want to stack…
2U 19 inch rack horizontal front panel mount for raspberry pi compute module CM4 and oled display These panel mounts require the DAP 2U MP-1 bracket. parts used: Raspberry Pi Compute Module 4 Compute Module 4 Base Board Heatsink 128x64…
This is just a simple stand that holds the Touchscreen as well as the IO-Board. I use this for developing for the cm4. Print Settings Printer Brand: Prusa Printer: I3 MK3S **Rafts:** No Supports: No **Filament:** Amazon BasicFil PETG…
A custom back for the HackberryPi_Zero mod Im doing. Ive installed a CM4 on to the Zero model for maximum thinness.
I use the Metatron22 case model and think it's great! Great work, buddy! 😃 But I still had a few cm4s lying around, without emmc, but with microsSD cards. And they don't fit in the case. So I enlarged the USB-C hole a little... voilà...…
No supports needed, 1X inbuilt support on one leg, that needs to be removed as per images. Required Hardware: 7x M3 brass inserts, 7x M3X12 SHCS Cap screws, 1x 40mm fan, 1x DC centrifugal blower, 60×60×15 mm. Print both parts upside down,…
This is a simple 1U mount for a 19" rack, a ThinkCentre M720q and similar models, a JetKVM, two Ethernet plugs and four Compute Blades with rear fan. The system is held together by two M6*50 screws with matching nuts and a reinforcement…
A remix of an existing raspberry pi cm4 i/o board case, simplifying the design as a case for development purposes. Also perfect for creating your own game console too! Supports are needed for the i/o ports.
Gridfinity 4x2 holder for Raspberry Pi Compute Module CM4 and oled display Designed, so that another 4x2 module should be stacked on top. parts used: Raspberry Pi Compute Module 4 Compute Module 4 Base Board Heatsink 128x64 1.3" oled…
Best printed face-down. I didn't need any vertical supports, but some brim doesn't hurt. Thank you @Mauker for the model that my work is closely based off of, and thanks to @Cicicok_1379995 and @toggledbits_70767 for the models that came…
Housing for OAK-D CM4 module to protect components from accidental touch and M6 mount to mount on any tripod mount. Module link: https://shop.luxonis.com/products/oak-d-cm4
A case for the WaveShare CM4-IO-POE dev board.Has tabs for wall mounting and holes for IO on both sides of board. It is designed to take a 20x40mm noctua fan for silent airflow but other fans with a 32mmx32mm hole spacing for mounting…
Add a pause during the print at 9mm to add washer to give more weight and stability In the holes at the upper add no head screw (M5x15) to have more grip
Parts needed: ¼ Inch threaded rod ¼ Inch nuts M3 threaded inserts M3 screws Main/extended io board mount compatibility: Original io board: https://www.waveshare.com/compute-module-4-io-board.htm Waveshare poe board:…
This is an enclosure for Raspberry Pi 4 Compute Module to be used with Cedar Plate solving app. Cedar™ implements a plate-solving electronic finder for showing where in the sky your telescope is pointed.…
I printed it with 30% infill so that the screw holes are a bit sturdier. Would probably work well with less since the mount is not exposed to a lot of stress/force. The bottom plate is a bit flimsy at 1mm thickness, but holds well and…
Basic holder for Green USB-C to a 7-port USB A 3.0 hub, model no. CM481 Will keep it from moving around. Specifically made it for size #8, 3/4" screws, but any small screws will work. Files included are the complete pair and each ends…
Waveshare Arduino CM4 base board box (WAV380) with active fan
Raspberry PI CM4 with IO Board
I remixed two models to fit to my purpose. I needed a rack mount for my Netgear GS308EPP and my Raspberry Pi CM4. Therefore I adapted the left rack mount base with some different spacings to fit the GS308EPP (75mm spacing) little loose…
I really liked this case design, however I wanted SD card cutout, heatset inserts and a way to mount it to a 2020 extrusion to use as a Klipper host. As an amateur at 3d modelling, my method of choice is to chop things up in the slicer…
I used Onshape to create a case for the CM4-POE-UPS-BOX. This is a link to what I modeled this after: https://www.waveshare.com/cm4-poe-ups-base-en.htm?sku=22850 . The lid for this model is friction fit. In the hole for the antenna, I…
Remixed a pegboard mounting plate to for use with Waveshare's CM4 IO PoE Box B case. I used M4x8mm flat head machine screws and M4 nuts from Home Depot to affix the case to the mount.
Retro Lite CM4 AIO Docking Station Link to official source: GitHub - StonedEdge/Retro-Lite-CM4-Dock: A docking station designed to be used with the Retro Lite CM4 gaming console. Description Updated: 2023/07/09 Note: Code base is now…
I'm using the external dimensions of the original WAGO 789-120 housing, but omitting the transparent 789-124 "flap" (cover). I'm designing my own housing designed to accommodate the CM4 and a base PCB. It will have at least two USB ports…
Slightly Extended Wind Tunnel when CM4 Cooler is also used
I designed a spacer for the ugreen cm400 ssd case, because the rubber ssd holder isn' capable to hold the ssd in place, in case of a drop. You can use one spacer, but i recommend too. I use PETG for printing the spacers because the ssd…
Raspberry Pi CM4 DFRobot Dual-Ethernet Fan Case Description Case for RPi CM4 using DFRobot Raspberry Pi Compute Module 4 IoT Router Carrier Board Mini Added a 25mm DC fan mount to the top of the case. Added a 50mm DC fan mount to the top…
Make your own CM4 carrier box for the DJI RC-N1 or RC-N3 This version includes: SPST mini on/off switch DPDT switch (for mode selection) USB-C port (for charging or wired power mode) 2.42 OLED screen(for system info, bat power, control…
Retro Lite CM4: Raspberry Pi Handheld Link to official Source: GitHub - StonedEdge/Retro-Lite-CM4: A CM4 gaming handheld, designed with the Switch Lite aesthetics in mind. Contains all STL files and code to build your own landscape retro…
Retro Lite CM4 AIO Docking Station Link to official source: GitHub - StonedEdge/Retro-Lite-CM4-Dock: A docking station designed to be used with the Retro Lite CM4 gaming console. Description Updated: 2023/07/09 Note: Code base is now…
I remixed two models to fit to my purpose. I needed a rack mount for my Netgear GS308EPP and my Raspberry Pi CM4. Therefore I adapted the left rack mount base with some different spacings to fit the GS308EPP (75mm spacing) little loose…
Best printed face-down. I didn't need any vertical supports, but some brim doesn't hurt. Thank you @Mauker for the model that my work is closely based off of, and thanks to @Cicicok_1379995 and @toggledbits_70767 for the models that came…
This is a Case for an Raspberry CM4 with an waveshare IO-Board-B. It features a panel at the bottom for maintenance the NVMe drive and an removable ventilation grille at the top. Ventilation slots on all sides ensure good airflow.
The WaveShare CM4-IO-POE-BOX-B is one of my favorite ways of deploying a Raspberry Pi and it already comes with a lot of the I/O options that I frequently need. It even accommodates some Raspberry Pi hats. But if you want to stack…
Print settings as usual. Add support to the wedged fork ends and to the M10 screw thread area. A Fusion f3d file has been added for those who want to tinker some more.
You can use any print settings as you desire, but these are the ones I used. Perimeters | 3 Layer Height | 0.10mm Infill | 80% Cubic Supports | None needed! Nozzle Size | 0.40mm Hardware Used M3x12mm M3 Threaded Inserts (Optional) 6 *…
CM4 IO board mount for 10" mini racks. Ports are exposed internally for "reverse" mounting.
Raspberry Pi Compute Module CM4 with Waveshare nano
This is a Case for an Raspberry CM4 with an waveshare IO-Board-B. It features a panel at the bottom for maintenance the NVMe drive and an removable ventilation grille at the top. Ventilation slots on all sides ensure good airflow.
This case for the Raspberry Pi Compute Moulde 4 TV Stick has to be slid over the entire module before the heat sink is attached. The HDMI connection cover is available in two versions, with and without air ducts. The idea behind that the…
Server rack mounting case for up to 4 CM4 Ether Boards. Create your mini Raspberry Pi CM4 server with. This takes 1.5U space of your standard media/server rack. More information about the CM4 Ether Board here:…
Case for the waveshare CM4 IO board, supporting the use of a 1U style server fan for cooling. Comes with two lids (with and without text). I printed this on a Creality Ender 3 S1 Pro using Sunlu Meta PLA. Note the tollerances are tight…
