Liczymy pasujące modele…
I was researching for a mount hand which can handle HyperX SoloCast Mic and found this attractive tablet/phone holder. Adapter which I create is not required any additional screws and nuts. You just replace part. Print instructions:…
Wydruk około 1,08 €–1,32 € nettoWstępna wycena jednego wariantu
When I got my KLP1 there were some problems by design. One Problem was the lower belt on the right rear side. The idler pulley is mounted too far to the left, resulting in a non-parallel belt path, resulting in different belt tension…
Pen plotter for Kingroon KLP1 New 2025 W.I.P. Pen plotter for klp1 210 https://www.printables.com/model/1354295-klp1-210-pen-plotter-revamped-wip Can fit any printer with 3010 fan close to the extruder! Tutorial inside the zip file!
The belt of the KLP1 has a lot of non-parallelism, and this design tries to solve the problem by shifting the position of the synchronizer wheel next to the right motor. The strength of the print may not be sufficient, please do not…
DIY Monitor Frame – Lenovo LP173WF4(SP)(F1) This is a 3D-printable frame for a Lenovo laptop LCD panel LP173WF4(SP)(F1) . The cutout is made precisely for this exact panel model – no universal fit. The design allows mounting of the LCD…
I hope this model helps you assemble the bed correctly since it's a hassle to have to remove it and not have it centered. The STL model is already ready to print on the same printer. I will also upload my profile, which has given me the…
I took inspiration & geometry of some of my favorite builders on here. Spliced together this beast using only my slicer. It is a rough draft, and you'll notice some crude splice points. I'm hoping this talented community takes this,…
After purchasing the KLP1, I was unpleasantly surprised that its hotend cooler never turns off. Another downside was the inductive sensor. I had an EBB42 in my stash, which I had long wanted to use for my heavily modified Anet A8 plus,…
It so happened that I got a universal 7" HDMI touch screen with the printer, but it was without a mount and was just lying around, which was inconvenient. I also needed to monitor the long printing process and make timelapses, so I bought…
On all my printers I'm used to using tennis balls instead of a 3D printer foot. It's very convenient, sometimes even beautiful, and isolates the printer sounds from the table well. Recently I got my hands on one of the very first KLP1s…
I printed it flat on the K1 build plate with no supports, 100% infill.
Summary This is the tool holder fitted to Kingroon KLP1. Print Settings Printer brand: Kingroon Printer: Kingroon KLP1 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 20% Filament brand: Kexcelled Filament color: Black…
After I uploaded my Bone-Extruder-Cover using Voronoi patterns I was asked for a clean STEP file for customization… and here it is 😉 Feel free to contact me if you find flaws or need some other improvements. Print it “face down”. The Hole…
Kingroon's support came through and provided me with the stl file for the KLP1 230 fan duct. Figure I upload it here to save everyone the trouble.
My Sony Alpha 6000 came supplied with a SELP1650 lens but without a lens hood. The lens hood I designed can be placed over the extended objective (when the camera is switched on) and still allows the use of filters, e.g. a polarizing…
Kingroon KLP1 230 fan duct mod for 5015 fan Print without supports
****UPDATE*** Someone figured out how to flash the original MOBO and THR so this isnt needed if you dont want to switch to BTT ecosystem. I have completely gutted all of Kingroons' control boards in my KLP1 230, and replaced them with BTT…
This is just a new toolhead cover I designed for use with a 5015 fan for KLP1 230. No supports 2 M3 screws 2 heatstake brass inserts 5015 fan If you are using the THR board you will need to cut and splice the original fan wire to connect…
Filament motion sensor. Erkennt Verstopfungen sowie wenn das Filament zu ende geht. Benötigt wird: 1 Kugellager 608 ZZ 1 optischer Endstop 1 Bowdenkupplung M10 Anpassung meiner Creation für den SV06 Optional zusätzliche Bowdenkupplung M10…
This is the reference size and holes of the Cheetah 2.2, I made it with a plastic caliper, so it may have a little variation from the real one, it is just a template not in detail, but it can serve as a reference to make some mod.
This is the reference size of the THR 2.0, I made it with a plastic caliper, so it may have a little variation from the real one, it is just a template not in detail, but it can serve as a reference to make some mod.
This is a side mount support for the Filament motion sensor KLP1 made by Stephan Schmitzberger. Usefull when using riser mods for the KLP1. To avoid any creep or deformation, i recommend to print in PETG or ABS, but PLA should work just…
The other day, i saw the AWESOME TNTBA Anti-vibration Feet created by TryNotToBreakAnything. And i wanted to try it on my Kingroon KLP1. So, i made an adapter. The adapter should be compatible with ANY printer that uses simple round feet…
Modifikation des Druckkopfes um ein BTT EBB 42 Board verbauen zu können. Zusätzlich durch die Magneten einfachere Wartung. Benötigte Teile für den Umbau: induktive Probe 5V M8 z.B. LJ8A3-2-Z/AX (orginal Probe arbeitet mit 24V wird von…
I have been wanting to get into more exotic filaments like ABS and ASA but don't want to give myself and my family cancer. After looking into recommendations I decided I needed a combo HEPA and activated carbon filter and ventilation. I…
I always take off the dust cover completely when playing records and the original hinges fall off easily and snap into “open” position. I have not used them at all for this reason but that means dust cover moves around and doesn't stay in…
I had lots of trouble with the stock sensor so I made this from a combo of 2 existing good designs I have used in the past. It has proven more reliable but not perfect as the filament will sometimes get caught just before the exit. I…
Improves the filament path with the support adjustment making a less curved filament at the sensor entrance. Only need 2 screws and 3 cables jumper male-female.
An additional element for a very successful mounting of the fan from this project https://www.printables.com/model/909825-klp1-extruder-fan-mount-remixed-updated Adds another holder attachment point and cable fixation for MKS THR. Add…
I made this after another owner asked for the measurements on reddit. It is made from my hand measurements and crappy CAD skills so it may not be perfect. Please edit and improve if you can.
This is a mount for the 210x210 version of the Kingroon KLP1. This mounts a Logitech C270 in the back left corner. It mounts using two screws for the stepper motor and hangs beneath the belts. To route the camera cord, I cut a small slit…
Extrusion style case for the WSPR-TX. The board slides in with slots in the case. To make the lettering on the front and back in a different color as in the photo, print with 0.2 mm layer height and set a color change at 0.6 mm and…
Moved the filament runout sensor to the left side for easier loading and unloading. I have a filament dryer that connects directly to the sensor. You will need to extend the wire. I used a male and female 3-pin XH-3Y and XH-3A to extend…
With this duct fan for Kingroon KLP1 230 I had a print qualaty improvement over the stok one. Printed in 0.2 layer hight. Need support just over a small part of the print.
After distroying two vertical pen holder, i create an horizontal one. It ll be fixed on the top right corner.
I have a Kingroon KLP1 210. Didnt like the printer head. So ive made a new one. Now, it uses a Shera micro extruder mirrored: https://www.printables.com/model/1258878-sherpa-micro-romz-remix-mirrored Other extruder should be compatible,…
A simple 3d stand for LENOVO LP1S case stand. Category: Organization
Raise the top cover 38mm at the front and 120mm at the rear. Include the exhaust fan and filament sensor at the rear. Place the filament tube and cable on top. PLA+
The LP101 end cap is designed to provide a clean and professional finish to aluminum LED strip profiles. It is typically made of durable plastic and fits snugly onto the end of the LED channel, covering exposed edges and protecting the…
Worth mentioning, I took all the measurements from the right side panel but the left one looks about the same. May not fit the newer KLP1 230 model - confirmation is welcome.
It needs 3xM3.5 countersink screws to mount.
Multiboard mount for a Tripp Lite TLP128TTUSBB 12 Outlet Power Strip. You will need to print two of them. Printing Guidelines: I printed using standard Multiboard settings. Use 3 perimeter wall thickness, 0.2 mm layer height, 15% infill,…
This is a simple mount to hold a LaserPecker LP1 in the tailstock of a wood lathe. It mounts in your #2mt tailstock and should have enough clearance for a straight USB-C power cable or the right angled one that comes with the device. The…
A simple LED housing for KLP1 210 W.I.P. (Work in progress) This is a working prototype, it will (most likely) improve in the future. Housing for LEDs of maximum width of 85mm. For 1 euro you can get 2m/5m of cold white 5v usb LEDs on…
Overview: This is a Bowden toolhead for the KLP1 210 that uses: Dragon ACE hotend, likely also Rapido/Rapido 2/Rapido ACE HF 4010 heatbreak fan (I use a Fabreeko Honeybadger) 5015 part cooling fan (I use a West3D Berserker Vindr) Beacon H…
KLP1 210 Pen Plotter Revamped W.I.P. Made to be able to reuse original 3010 mounting screws. Required: 2x m3 (atleast) 10mm screws (to tighten the pen inside the holder) 2x m3 (atleast) 5mm screws (screwed into the mount for the rubber…
Work in progress. A adapter from THR board to EBB36 board. Needs modified fan shroud. EBB42 should be a better choice.
fits LG LP1200DXR portable A/C systems old wheel had small finger attachments this uses a full hub for better support.
Underneath mounting LP-16 socket case. Initialy designed for a M3x20 screws.
Looking for a solution to reliably hookup CAN devices, fans, sensors and more to your beloved 🥰 VORON with a tiny bit of 😎 premium touch ? This custom skirt for CNLINKO LP12 (and compatible) connectors might be it! Why This Mod Exists…
Adaptador para reemplazar el THR 2.0 de la KLP 230 por un Bigtreetech EBB42. Incluye también una modificación para el ventilador 5020 de la máquina. Lo imprimí en nailon ePA-CF debido a la alta temperatura de la cámara y su proximidad a…
DIY Monitor Frame – Lenovo LP173WF4(SP)(F1) This is a 3D-printable frame for a Lenovo laptop LCD panel LP173WF4(SP)(F1) . The cutout is made precisely for this exact panel model – no universal fit. The design allows mounting of the LCD…
I hope this model helps you assemble the bed correctly since it's a hassle to have to remove it and not have it centered. The STL model is already ready to print on the same printer. I will also upload my profile, which has given me the…
Print Material : ASA Recommended. PETG will do for lower temps/quick needs to print an ASA version. Remix of 2 models on makerworld. Improvements made for easier printing and/or alignment and strength. The fan was redesigned as the…
This is an almost exact replica of the original hinge. You'll need a 3mm pin, a spring with a diameter of 8mm or less (the stiffer, the better - the original spring is very stiff), and any metal washer/spacer above the spring to create a…
Frame for mounting the extruder and cutter from the Bambulab P1S onto the first-revision Kingroon KLP1 210.
I took inspiration & geometry of some of my favorite builders on here. Spliced together this beast using only my slicer. It is a rough draft, and you'll notice some crude splice points. I'm hoping this talented community takes this,…
After purchasing the KLP1, I was unpleasantly surprised that its hotend cooler never turns off. Another downside was the inductive sensor. I had an EBB42 in my stash, which I had long wanted to use for my heavily modified Anet A8 plus,…
It so happened that I got a universal 7" HDMI touch screen with the printer, but it was without a mount and was just lying around, which was inconvenient. I also needed to monitor the long printing process and make timelapses, so I bought…
On all my printers I'm used to using tennis balls instead of a 3D printer foot. It's very convenient, sometimes even beautiful, and isolates the printer sounds from the table well. Recently I got my hands on one of the very first KLP1s…
This is a removable cone shield for the Laserpecker LP1. The cone shield is attached with magnets to the included cover that goes on top of the laser unit. As long as the user is OK with not witnessing the entire process, this is a good…
Fits a little tight. might be able to print at 99% for an easier fit. I just hit it on with a hammer and it fit fine.
Vinyl record / LP Records holder, so I have a easy place to put the record while playing it. Solidworks is provided for easy remix.
I accidentally threw away the hinges for my turntable's dust cover so I made these replacements. It was a bit expensive to buy 2 hinges online so I designed and printed these. I have at the AT-LP120 USB, but it should fit these models:…
Arm lock knob for turntable for Audiotechnica AT-LP120-USB
Adjustable Stand for Laserpecker 1, Printed in PLA with 15 % infill. Add 3/4 inch Dowels from Walmart to Complete Project. Adjusting Ring slides on Vertical dowel under LP1 Holder. Printed in PLA with 15% infill.
Part that is useless now can be a hex tool holder. It might get handy as battery contacts are not phillips head standard as usual. Simply unscrew the original and replace. Caution: this design requires battery belt to secure the hex tool…
I had an old, slow laptop that had not been used for years. I repurposed the screen, using an external controller board, designed and printed a case for the controller board and ‘feet’ for the monitor brackets. The controller board is…
You will find different versions in different heights. I have only printed the 6U versions. If you have wishes for other versions, write me a PM or a comment.
Kingroon KLP1 Head model + Fan blower for 5015 fan replacement
adaptation de la sortie ventilateur extrudeur pour adapter un 5015 standard 1-découper 4 mm aux oreilles de fixation du 5015 2-récupérer la fiche jst 2mm de l'ancien ventilo imprimé en ABS pour la température
On the KLP1 you have to always disassemble the hotend to reach the screws that keep the belt in place in case you want to change belts or tighten it more. This is really annoying and honestly just a bad design. So i made a belt tensioner…
Basically a wider original duct with a vent attach to the back. It can just replace OEM part without modifying housing. Recommend to print at 0.15mm layer hight. Use only one screw to bolt on original spot. No Support Needed This desigh…
A replacement tone arm rest lock clamp for AT-LP120-USB turntable from Audio Technica. The piece can easily be bought online from different suppliers but it can also be printed. I printed mine in PLA when the original broke. The…
These are customized support feet printed in TPU, they greatly reduce the vibrations of the structure, I recommend re-calibrating the input shaper after installing them because they modify the resonance frequencies The correct orientation…
Tired of having the damn pen wandering around the lab lost among the tools or stuck to some frame panel so that it makes a terrible noise when the printer vibrates? This is a simple and functional design of a pen holder for the touch…
A new spool holder design which allows you to lower the filament spool mount point by 10cm ensuring correct sliding of the filament with less friction. This version has a wider hook so it is possible to insert reels of a wider thickness…
The work on the project is still in progress , for any doubts feel free to leave a comment or contact me on the Kingroon community group (user Glitch08). The goals are: -Modular design, easy to print without support and customizable. (you…
My design is to make the side panel of the KLP1 an openable door so that you can install the filament in the door and hide it inside the machine to retard the filament from moisture. The design of chain is designed to compensate for the…
Die Füße sind 40mm hoch, dadurch dreht sich der Lüfter an der Unterseite nicht mehr so hoch und wird dadurch leiser.
it's Kingroon KLP1 Extruder part, not for print, just to help you design. I spent almost a day measuring and modeling the klp1 extruder parts. If you need this object to help you adapt the klp1 extruder to your modification, welcome to…
本模型为启庞KLP1适用的活性炭空气净化模块，同时也适用于很多其他打印机以及常规的桌面使用。需要用的到的材料有：100*100*50mm蜂窝活性炭（这在淘宝网通常可以成箱购买，价格低廉）、7530涡轮风扇、M3热熔螺母*3、M3*5螺丝*3、M3*40螺丝*2、M3螺母*2以及一个移动电源盒。 Some harmful particles could be released during the printing process, especially with…
A simple mod to raise the top lid. 2 versions available; for brass threaded inserts or self tapping screws. 4.5 mm diameter of holes for threaded inserts, 2.7 mm holes for self tapping. Corners are symmetric. First print 1 long piece and…
Well just a 30mm spacer for the top (print 4) and some caps for the M3 hardware uses 20x M3x40 hex screw. And the feet , print in TPU (print 4)
Everybody lowers the spool , and that makes sense , but filament sensor is not in center of spool, this print will take it a bit further to the center , not perfect , but wires is not any longer :-) uses 2x M3x35 hex bolts (40mm with some…
Kingroon KLP1 Extruder part by lxlolxl | Download free STL model | Printables.com Used this
30mm riser for the top plate of the Kingroon KLP1. The screws to mount the riser to the frame are hidden inside, a ball head hex driver is needed. STEP files included, feel free to remix edit: added FreeCAD file edit: added 230 version…
The KLP-1 has an issue where the hotend whip (cable and feed tube) drag on the lid of the printer. Also, the lid doesn't have a backstop, which is mildly annoying. There are some designs already out there to elevate the entire top of the…
Nothing much to say that wasn't in the summary, this just adapts the stock filament runout sensor on the KLP1 so you can screw in a standard pneumatic fitting. That means you can feed filament in from the back of the printer without the…
This is a lighter-weight replacement for the stock shroud on the KLP1 toolhead, that lets you use a standard form-factor 5015 blower fan (the OEM part has a larger port). I measured the stock shroud at 80.5 grams, and the replacement…
![[WIP]DIY Monitor from Lenovo laptop LCD LP173WF4(SP)(F1) and similar](https://media.printables.com/media/prints/9272192f-4229-417d-b2d2-dbcbfd00428c/images/11305362_1e41f76b-e0a1-40af-966f-d6433e1f4609_541741c1-beac-42ac-9531-adc52c7cf939/pxl_20251130_120236148.jpg)
