Liczymy pasujące modele…
A little case for the ST Microelectronics Nucleo-64 Development Kit. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. The screw on the left side is…
A little case for the ST Microelectronics Nucleo-144 Development Kit. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. The screw on the left side is…
General Pressing in the subframe bushings (e.g. 3507923, 3507924) into Volvo P80/P2 subframes is challenging, because they sit very tight, have to be oriented correctly and when pressing on the rubber “crown” or the inside part of the…
The center tab of the kickpanel on the drivers side in P80 series Volvos (V70I, S70) tends to break. Since it is the only screw holding the kickpanel in place, it is a rather important mounting tab. Repairing it is difficult since the…
General Pressing in camshaft seals can be challenging and if not pressed to the right depth or pressed in crooked, they will leak. Volvo used to make a special tool (9995718 or 999 5718), but it is hard to get and if you can get it, it's…
General The 25mm version is compatible with 1 inch cable grommets as shown in the picture below as well as M25 cable glands. But you can use the blank plate to remix your own version if you have different needs for your car 😄 The gasket…
This adapter enables you to use your old Prusament spools as a Multispool for filament refills of the “Recycling Fabrik” https://www.recyclingfabrik.com It is a sturdy and long lasting alternative to fully printed spools and the refill is…
An upgraded version of Deluxe Designs Polaroid frame, which features a nail hole of 5mm so you can hang it on a wall. The Polaroid slides in from the top and is centered by the frame. The frame works for the Polaroid 600 film and all…
General Pressing in camshaft seals can be challenging and if not pressed to the right depth or pressed in crooked, they will leak. Volvo used to make a special tool (9995450 or 999 5450), but it is hard to get and if you can get it, it's…
The studs for the muffler heat shield on P2 series Volvos (V70II, S60I, S80) corrode due to the influence of moisture, the contact between aluminium and steel, temperature and of course age. The result is that the original plastic nut…
The silicone seal in the electrical connectors of the type STD 7614.31 (Volvo part number 9144275) used in P80 series Volvos (V70I, S70) and probably other from the period as well deteriote over time. The silicone becomes brittle and…
The clips of the red side marking lights in all four doors of P80 series Volvos (V70I, S70) tend to break when you try to remove them to change the light bulbs. Sometimes they even break when slamming the door too much. While the lights…
General Pressing in camshaft seals can be challenging and if not pressed to the right depth or pressed in crooked, they will leak. Volvo used to make a special tool (9995719 or 999 5719), but it is hard to get and if you can get it, it's…
This is a remix of felixna's model with an added slot for the fan's cable as suggested by Thomas Albrecht in the comments of the original model. The notch is measured from a Noctua Redux fan, but it should be very similar for most fans.…
A little case for the Nordic Semiconductor nRF52 DK Development Kit. This case specifically works with the nRF52832 development kit, others might fit as well. The board should “snap” into place, it sits quite firmly in the case itself and…
General Pressing in camshaft seals can be challenging and if not pressed to the right depth or pressed in crooked, they will leak. Volvo used to make a special tool (9995449 or 999 5449), but it is hard to get and if you can get it, it's…
A little holder for your TP-Link TL-SF1008D eight port ethernet switch. You can conveniently slide the switch in and have it secured by the clip. Pulling on the ethernet cables only pulls the switch tighter into the mount, not out of it…
This model is a replacement for the Volvo Retaining Clip with the part number 352393, which is no longer available from Volvo. The clip fixes the rear ABS sensor wire to the brake hose to avoid it from rubbing. The old plastic often…
General The hub cap is designed for a 75mm center hole of the Sprint Star steel wheels. Make sure that your hub has the correct dimensions. The provided STEP file does not have two colors, this was done with the material change option in…
General A little 40mm plug with a knob to plug the drive shaft holes of a Volvo M56 gearbox (or any other transmission with 40mm diameter seals). This can be considered a substitution for the Volvo special tool 999 5488. Recommended…
This is a remixed version of the original Recycling Fabrik MultiSpool, utilizing my Prusa Spool core for Recycling Fabrik Refills. The side pieces are thicker and the refill is held much tighter by the spool than by the original…
The Hella UP5.0 vacuum pump is a universal vacuum pump that can be used to create or enhance brake vacuum in cars that either do not create engine vacuum like DIY electric vehicles or for hot rod or tuning applications. In order to mount…
General This is a replacement for the rubber buffer for the Land Rover Series side panel (part numbers 338553 and 338550). Commercial replacements are available but of varying quality and sometimes hard to come by. The center hole fits an…
General Pressing in CV axle seals can be challenging and if not pressed to the right depth or pressed in crooked, they will leak. Volvo used to make a special tool (9995541 or 999 5541), but it is hard to get and if you can get it, it's…
When assembling a large quantity of LACK tables from IKEA, screwing in the feet will become really hard on your hand. Therefore you can use this handy wrech to help you install the feet. This wrench has an inner diameter of 51x51mm which…
A little case for the Nordic Semiconductor nRF52 DK Development Kit. This case specifically works with the nRF52840 development kit, others might fit as well. The board should “snap” into place, it sits quite firmly in the case itself and…
General This is a replacement for the clutch slave cylinder flange gasket used on manual gearboxes of the Mercedes-Benz W124. The Mercedes-Benz part number is A1242950087/1242950087. You can also find a .dxf file you could potentially use…
General The original shims between the frame and the rear body tub are made from aluminium and are only available in a single size. If you want to adjust the door gaps and general fitment of the body, it's nice to have custom thicknesses.…
This gland can be used for the DC supply lines Versions With supports: The “skirt” and added layer above that covering the 6mm hole enable a print without further support. If the perimeters are printed from the inside out, the O-Ring…
Keeping dirt, debris and moisture out of your A/C compressor (and A/C system in general) is very important. If you don't have any suitable plugs at hand, you can 3D print your own and save some time and money (and potentially your A/C…
General This is a replacement for the rubber washer for the Land Rover Series roof (part number 302373). Commercial replacements are available but as you need 14 for the 109 wheelbase, printing can be cheaper. The center hole fits an M6…
Versions With Support: These models have a little support material added and a bridge for the mounting holes, which makes it possible to print the model entirely without additional supports. With Cutout: Our PTO hole (replacement frame…
Versions With supports: The “skirt” and added layer above that covering the 6mm hole enable a print without further support. If the perimeters are printed from the inside out, the O-Ring groove can be printed without supports as well.…
Versions Blank: If you don't want to use the port, you can put in the blank plug to seal it off. M16: For small diameter cables as in the original application this gland is sufficient. Currently all versions are universal, so you can plug…
This gland can be used for the Signal cables Versions M16: For small diameter cables or Bulgin PX connector (or similar). M20: For larger diameter cables. Waipu SP21: If you want to replace the original connector with a 7- or 9-pin Waipu…
General This is a replacement for the rubber corner for the Land Rover Series and early Defender B- and C-Pillar (part number 33215). Commercial replacements are available but as you need 4 or 6 for each vehicle, printing can be cheaper.…
General This is a replacement for the thermostat housing gasket used on the Mercedes-Benz OM616 and OM617 engines with the Mercedes part numbers A6162030280, A6172030080 and Elring part number 811.077. Currently it's hard to find the…
This is the cable gland for the 230V power input for the Outlander Charger. Versions With supports: The “skirt” enables a print without further support. If the perimeters are printed from the inside out, the O-Ring groove can be printed…
General The Cisco WS-CAC-3000W is a very powerful 42V volt power supply which can be bought very cheaply on ebay as NOS or used. Since it was meant to be mounted inside the custom Cisco hardware, it doesn't sit flush on a surface because…
Versions M16: For small diameter cables as in the original application this gland is sufficient. M20: This is the largest possible option. Waipu SP21: If you want to replace the original connector with a 7- or 9-pin Waipu SP21 connector.…
General This is a replacement for the chain tensioner gasket used on the Mercedes-Benz OM617 engines with the Mercedes part number A6170520280 and Elring part number 773.361. Currently it's hard to find the gasket individually, so you can…
A little case for the Lattice Semiconductor iCE40 UltraPlus Breakout Board. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. Recommended Material &…
This data can be useful if you want to use the Mitsubishi Outlander Rear Motor for your DIY EV conversion and need the exact location of the mounting holes in relation to the front mounting surface. Files Mounting Plate: can be…
General Pressing out the front lower ball joints from Volvo P2s is challenging because they are pressed in and can be additionally tight due to corrosion. This tool can help with the removal as it can be used to apply preload to the ball…
When you want to utilize the Mitsuibishi Outlander AC Compressor in your DIY EV conversion, you will have to create a bracket to mount it. Due to it's shape, getting the bolt pattern is not super trivial since they have different heights…
General This is a replacement for the no longer available Honda NTV650 headlight brackets 61316-MZ6-000, 61317-MZ6-000. The original brackets are stamped, so left and right side are different. This one is just flat, so it doesn't matter.…
General This is a replacement for the Land Rover Series Gearbox Top Cover Gasket (FRC3776) which is often only available as a cork gasket. You can scale the z-height of the model if you need the gasket to be thicker or thinner or you can…
A little case for the Lattice Semiconductor iCE40 UltraPlus Breakout Board. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. Recommended Material &…
When converting a vehicle from Manual to Automatic or to Electric, the clutch master cylinder is not used anymore, leaving a hole in the firewall. Automatic cars came with a cover washer in place of the master cylinder, but it appears to…
This is a scan of a Honda VF750F RC15 instrument cluster. It mostly covers the top surface and the mounting "ears". The goal of the scan is to design a custom enclosure for a Naked Bike conversion.
This adapter enables you to use your old Prusament spools as a MasterSpool for 800g filament refills from Das Filament. The Refill sits tighter in the adapter than in the original MasterSpool. It is a sturdy and long lasting alternative…
A little case for the Cologne Chip GateMate CCGM1A1/A2/A4 Evaluation Boards and Programmers from the GateMate FPGA Starter Kit. The evaluation board sits snugly in the case itself and is held down by additional screws. The original rubber…
General This is a replacement for the original Puig CS1 Mini Windshield mounting bracket. Compared to the original, the new bracket has a deeper slot so you can mount the windshield lower on your headlight. The original had a very big gap…
To wszystkie aktualnie dostępne wyniki.
