Liczymy pasujące modele…
I wanted a chip bag clip, I looked on thingiverse but I couldn't find any I wanted, a lot were a waste of plastic, I don't need it to look like a shark, or anything else when there is a 99% chance that my toddler will just lose it, I was…
I wanted a better brush cleaner than a sour cream container so I decided to design one. My first version was a single water well but realized that I didn't really want two separate water wells one for dirty water and one for clean water…
I lost the thumb stick to my Odin 2 and didn't want to pay $10-$30 on etsy to buy a set so I designed my own and they worked out great. My sticks are 2mm taller than the original to give you a little extra control and for the taller ones…
A buddy of mine bought some USB buck converter boards and was going to make an adapter cable and I had the idea of this box instead. It has one set of power poles in and 2 sets out, and then USB to power a PI, what have you. This box is…
I wanted something on my desk that was not huge, bright red and with bio hazard signs on it for my diabetic pen needles so I came up with this. It has a needle bender for both ends of the needle cap, one is just a hole, lay the needle at…
Newton101 designed a really cute toy car, I printed it out and it had very sharp edges, the pegs of the tires broke off easily, and the wheels are a chocking haszard, they were 23mm in diameter which is 0.9" and in the U.S. the choking…
Here is a drop in dock for the GPD Win Max 2, to me it is holding it at the perfect angle to type on while able to get plenty of air flow to the vent. I cut out for the speakers, USB ports, micro SD cards etc. This is big so it probably…
A 49:1 box for an end fed antenna printed 3 perimeters, 6 top and bottom layers, infill doesn't matter. Category: Electronics
I broke the HappyModel EOS2 canopy that I purchased, the screws ripped right out of screw holes, also the camera angle would change every time someone sneezed in my house so I figured it was time to design a new one. I did design this so…
I designed these for 10 series aluminum extrusions that are 1" x 1" square. key differences over others of the same, the nut is twisted to grab mor metal when tightened, and the corners are rounded for easier printing. Long version: As…
Here is a drop in dock for the GPD Win Mini v2 I added a groove up front to make it easier to get in and out. I printed it in PLA with no supports
I made a hula hoop gate, there are 2 versions, one uses the full hoop (small hoop) and the other you cut the hoop in half. The half hoop feet stack (not tightly but enough to help carry, there is a hole to tie some twine in between the…
Newton101 designed a really cute toy car, I printed it out and it had very sharp edges, the pegs of the tires broke off easily, and the wheels are a chocking haszard, they were 23mm in diameter which is 0.9" and in the U.S. the choking…
I broke the HappyModel EOS2 canopy that I purchased, the screws ripped right out of screw holes, also the camera angle would change every time someone sneezed in my house so I figured it was time to design a new one. I did design this so…
I bought the Eachine EV100 FPV goggles as my first goggles but they really didn't fit my big head, no matter how I adjusted the PID it would still blur the outside edges. I found the replacement shell from Lichy but honestly nothing fit…
My inlaws gave us their old refrigerator when ours broke and it had some broken/missing shelf end caps, and a shelf bar missing. I took one of the existing ones and made a model of it, it worked out perfectly made a great replacement. My…
Here is a case I made a while back for 75mm quads, it fits the mobula7, beta75x, beta75 pro, pretty much all 75mm brushless quads. v1 has a rounded bottom. v2 has a bottom that is grooved to allow you to stack the lid under the bottom.…
Here is the JuiceBox 2.0, it now has a USB C & A buck converter in it. It is still 1 PowerPole input and 2 PowerPole output. Here is the link to the buck converter used: https://www.amazon.com/dp/B09D98799T I printed mine in Orange ASA to…
I picked up a used Uniden BC125AT and the antenna was pulling it over so I made a desk stand for it.
I have a weird shaped door knob that none of the CP covers fit so I had to modify Fritdiverdowns mod, so this is a mod of a mod. ;-) Looking at lowes.com to see what these 1960s door knobs are, there are a few names for the same thing but…
This is a case for a Duplex Ham Radio hotspot. Put the Hotspot hat together with the raspberry pi and then put it in the case. The screws are M2, you will need 6 of them. Category: Electronics
This box holds a 1:1 balun and a choke, I used FT240s and a mix 61 for the 1:1 and a mix 31 for the choke as per the Palomar website. https://palomar-engineers.com/ferrite-products/ferrite-cores/ferrite-mix-selection I ran window line…
I din't like the options at MFJ for a PowerPole distribution blocks so I made my own. The center is just a piece of double sided circuit board, you just want blank double sided, no through holes. Tthe piece I used was 35mm x 21mm cut from…
A modular gate for small quadcopters like the Tiny Whoop or the Inductrix. I got the idea when I saw http://www.thingiverse.com/thing:1730984 but that is unusable, wasn't finished and seems to be abandoned. Each piece as a tab and a hole…
I built Corben33s Jelly Bean Dispensor but wanted to make a few improvements. Changes: · Made a catching tray so the candy does not shoot across my desk. · Tweaked the shelves extending them to give more movement · Cut the bottom leading…
This is a case for the Rig Expert AA-30 Zero hat that goes on top of an Ardiuno Uno, it has a keypad and display. Here is the link to the keypad and display…
Upon request I made a 2s lipo holder to fit the version 1 and 2 Mobula7 frame as they come designed for 1s batteries. Designed to be printed out of TPU. I printed at 0.15mm layer height, don't need support (looks like it does but prints…
Here is a lay in dock for the GPD Win Mini for when the grips are attached. v2 Added a groove in the front to make it easier to get in and out, also I rounded the front edges. Printed in PLA no supports.
Here is a case I made a while back for 65mm quads, it fits the ur65, mobula6, beta65x, beta65 pro, pretty much all 65mm brushless quads. v1 has a rounded bottom. v2 has a bottom that is grooved to allow you to stack the lid under the…
I had an idea for this, I looked online and sure enough Nintendo has one already but it is only for the NEW 3DS XL not the original so that did me no good. I made it stand on it's back so that it saves space, I have very little on my…
Made a foot to turn a pool noodle into a gate for flying ultra micro quads through. It has a hole for some twine to hold them together so you don't have to stake them down, you can use the stake holes to hang them on the wall too. It…
Let me start off by saying that I did not design this USB cable holder but in looking around I really liked it a lot but I like rounded corners especially on things that are permanently mounted, too many accidents on square hard corners…
This is a canopy to go with the EOS1/2 adjustable camera mount for whoop style quads. It allows you to adjust the angle without getting in the way of the camera but it also gives a little more protection to the camera than the stock…
This is a battery powered Ham Radio HotSpot. It uses an 18650 battery and a charging upconverter to power the Raspberry Pi HotSpot. Find the build video here: https://www.youtube.com/watch?v=4mQEDI5QX4E Parts List: Raspberry Pi Zero W…
Do you want a 2s 65mm "whoop"? I made a 2s 300-350mah battery holder to fit a 65mm frame, you need to cut away the old 1s holder. I did not turn the battery on it's side as it just starts to hang too low at that point. It works with…
I have been working on a bunch of Mobula7 adapters for different batteries and to make use of a Beta75 Pro frame and in doing all that I had a great idea on how to improve on the original adapter that came with the Mobula7. This one is…
This is a battery box for the Bioenno BLF-1209A 9ah battery. It includes 2 sets of power poles, and USB A and C adapter. I made it to plug into the existing plugs on the battery so I did not have to cut the battery leads to keep the…
I revised my EOS2 whoop camera mount to now be able to mount the AKK KX5 VTX inside the canopy with cutouts for the channel button and the display. Print at 0.1mm and with support especially if using TPU and you want the top to turn out…
Is your Beta65x or Beta75x going a little too fast indoors or not fast enough outside then this will let you adjust the camera angle to slow you down or speed you up. It fits the stock Z02 camera and VTX. The stock canopy fits but you…
I tried the stands for the X9D and they were either too flimsy or didn't tilt back enough so as soon as you sat the transmitter down it would fold in and collapse so I designed one. It leaves the ports on the back of the X9D open so you…
I found Bill84s corner bracket and printed out a pair for my new printer but I was going to be using bolts instead of screws so where his support bracket in the back was wouldn't work for me as I couldn't get a socket in there (the irony…
This is a modified CoreXY setup I have been working on, I have to do the corner bearing holder and the motor mount yet, this is for a printer I am creating, it uses LME12UU bearings and 12mm shafts, I went bigger as this is also used in a…
I ruined one of my lipo batteries by pancaking it into the ground so I thought it would be better to have some sort of protector and maybe save that $10 battery. This is a fully parametric design, you just need to put your battery height,…
Adjustable camera mount for the WolfWhoop P-1 camera designed to fit "Whoop" style quads. Print at 0.1mm layer height Category: R/C Vehicles
This fits between the 2 battery holder bars of the Mobula7 frame, put the longer side in first and then squish and pop the other side in. This also fits the Beta75pro frame if you cut off the existing battery holder trimming it flush and…
Here is a spacer so you can use the Mobula7 camera on other frames without the camera hitting the board. The connector strips are 1 layer thick and add virtually nothing to the weight but are useful to hold the spacers in place to screw…
I know, I know, we need another 3D printer design like we need a hole in our heads but..... I love the Ultimaker with a passion, in my opinion it is THE printer to beat, it has the smallest layer height of a personal FFF printer I have…
I wanted a canopy for the new Runcam Nano 3 so I made one, I have different versions I am working on but the "half canopy" version is finished since I am posting it. My canopy and mount come in at 1.4 grams, the original Mobula 6 canopy,…
This is a canopy that holds the Caddx EOS1-2 cameras. (EOS1 needs to be the later model with mounting holes on the side) It will fit any of the "Whoop" style quads as long as it has the power to lift the camera, it fits the beta75x and…
I love Mad Mikes low profile thumb stick for my X9D that I had to have them on my X-Lite. I kept the basic thumb grip but change a few things so that they wouldn't bottom out and so that they would fit the xlite screws. I posted both…
A friend asked me to make an SMA mount for his XHOVER WIN 3" frame. f3d file included. Category: R/C Vehicles
I wanted a low profile wall mount (mine is screwed into the side of a shelf) for my transmitter. I have been using the wide one for a while but when I added a kickstand to my transmitter the normal mount was too long so I redesigned it a…
I was asked to help redesign the Z02 camera mount that BetaFPV had for their camera to fit the EOS1/2 cameras, many iterations with lots of collaboration we have finally settled on a mount that fits under the canopy, holds the camera, is…
All credit for this design goes to Spanner Hands, it is his baby, I just modified it. You need the top and bottom I modified, 4 bearings (listed below) and 2 of the rollers. all other parts are identical to Spanner Hands box and can be…
Here is a battery holder for "Whoop" style stick batteries, it was tested with BetaFPV 300mah and smaller batteries. You can adjust the columns and rows to hold more or less batteries. it is designed so that it will stack on the lid when…
This is a 2s stick battery adapter for a 65mm frame like the Beta65 pro and the UR65 and probably others, those are the only 2 I have though. You can either cut out the old battery holder or just leave it, if you leave it then it is just…
To convert a Beta75 Pro frame to work with the Mobula7 I found the best way is to trim the existing battery holder off and then use one of the ones I designed made out of TPU. I had designed a battery holder that just slid into the…
This is a 2s to 1s adapter so that you can use the Beta75 pro frame with the Mobula7. Slide the adapter in place, it takes a little wiggling and will snap into place, then slide your batteries in and your done. It weighs 3 grams printed…
Here are a couple stick battery holders so you can use 2 stick batteries for the Mobula7 and mainly so you can use the Beta75 Pro frame as a replacement frame for the Mobula7. I like the vertically stacked one better as the horizontal one…
The original primo canopy in my opinion had some design flaws to it so I took my EOS2 mobula7 canopy and converted it to work on primo style frames. No adapter needed to hold the EOS2 just screw it in. It clears the whoop vtx as well. I…
This is a flashing adapter for the HK 10amp UBec ESC. This will give you a clothes pin style clip to make contact with the contacts on the board. I am not going to go into details on flashing the ESC as there are already numerous sites…
The PSU mount that comes with the Anycubic linear plus delta printer mounts the PSU straight across the corner of the printer, you cannot mount it on the side of the corner extrusion so it either shoves the PSU into your face or if put on…
If you get these from amazon they were 50 degrees off for me and I spent 2 days calibrating them, after calibrating I could print PLA as normal instead of at 220c and now I can get the wood grain effect with my wood filament.. If you…
I bought some Makerfire gates from Good Venture Drones, they have hooks to hang them and I was thinking about stapling them in the house here and there for a track but decided that would be a PITA.I then thought about a stand with feet,…
I made some gimbal stick protectors to work with the modified Mad Mike low profile stick ends that I modded for the X-Lite https://www.thingiverse.com/thing:3146292 Category: R/C Vehicles
I designed and made this to dispense disposable baby bottle liners, it works better than grabbing the box each time. These are the liners we use that I made it around but it should work with others. Playtex Baby Nurser Drop-Ins Baby…
This is a flashing adapter for the HK 20/30amp ubec ESC. This will give you a clothes pin style clip to make contact with the contacts on the board. I am not going to go into details on flashing the ESC as there are already numerous sites…
My work picked up a Malyan M180 and the spool holders were not big enough around. I designed these to fit the spools I use but being the same height as the originals and designed to used the bearings from the original holders. Added a 58…
The FXT Viper screen when mounted into the googles cannot use a standard SMA thumbscrew adapter as the goggle gets in the way so I designed these so you can easily get the antennas off and on. I did a larger grip area for your normal…
I needed a mount for an MKS SBase board to mount into my Anycubic linear plus delta. I then added 3 external driver mounts to add TMC2100s on X,Y,Z It has the height of the board set to put the usb/ethernet/sdcard in between the 2 2020…
I picked up a KingKong ET115 and wanted a snug case for it. I have printed the case for the ET115 as that is what I own but I had searched the net and asked people that have the ET100 and ET125 for the outer prop guard diameter to make…
To wszystkie aktualnie dostępne wyniki.
