Liczymy pasujące modele…
This is a fix to the sharp angle in the Comgrow/Sovol SH02 Filament Dryer Box. The factory guide would cause excess bends and jams causing failed prints unable to pull form the box. This puts it more of a vertical instead of a parallel…
Some custom parts and other mods for the SOVOL SH01 filament dryer (also badged under the brand Comgrow). I noticed there was a decent cavity towards the back of the box that's blocked off and designed this alternative insert to make that…
If you have a sovol SH02 filament dryer, you know how annoying the fan is. This fever dream of a mod replaces the stock fan with an off the shelf 40mm computer fan and makes the dryer essentially silent. You will need, at minimum; A 40mm…
Adapter for the T300/T500 to Bambu Hot End. DO NOT ATTEMPT UNLESS YOU'RE MECHANICAL! -Prints with no supports PARTS LIST: Hot end: Bambu X1 clone https://a.co/d/dsEMpa1 Inserts: 2x M3*4 4x M2*3 https://a.co/d/7Aj9c0x Bolts: 3x M3 x 10mm…
9/29/22: By suggestion from Astroprinter I reworked v15 to redirect some of the cooling air down through the cone to help keep smoke/debris from flowing up around the lens. Update: I've been doing some wood etching and it's become…
…Please be sure to hit like & post a make, I'd love to see your prints! Mount a USB camera on your T300! With hidden channels for cables! Use original bolts to mount. Be sure to check out a matching model for a physical button on the…
Comgrow 3018 CNC Z Probe Holder. Holds the Z-Probe and has an area to clip the aligator clip into. Use double-sided tape to apply onto machine. Printed in PLA - No supports. If you download and use please like this model and upload a make…
Just some basic pieces to fix te machine in place with screws, also a quick focus gauge.
I did not like how the PSU was separate from the dryer box and how much waste heat was being thrown off of it never to be utilized by the dryer box. Of course this isn't going to significantly impact efficiency in any way but it helps…
I designed my own version of an air assist nozzle for this laser engraver/cutter. The air pump that I’ve got was a bit of a trade off between power and noise. Therefore I designed the nozzle to minimise air leakage and get the most out of…
The Comgrow SH02 filament dry box is amazing but unless it's kept open a few inches while operating, there is not enough outflow for proper dehumidification. What is FAR WORSE is the placement of the filament ports. This model has 2 ports…
This adapter system wraps the edges of a COMGROW 1kg 199x63mm cardboard spool in order to: provide smooth rotation within a Bambu Lab AMS prevent carboard debris from depositing within a Bambu Lab AMS Features: Reusable COMGROW nameplate…
I use this 120mm exhaust fan adapter for my Comgrow laser engraver Category: Tools
Upgrade Comgrow T500/T300 hot end cooling fan to quieter larger fan. Fan: WINSINN 40mm Fan 24V https://a.co/d/aEnkuMs
Designed to fit in the bottom slots of my Comgrow heated dry box. Printed in PETG on my Flashforge Adventurer 5M. Be wary of the thin walls, I recommend lowering your speeds to 90% printing this. Got mine to print first try. I filled mine…
I built a DIY laser engraver around the Comgrow 10W laser module , and decided to design an air assist for it that replaces the existing laser shield. This should also fit the Comgrow Comgo Z1 module. This will work with a ~6mm air hose,…
The Comgrow T500 is equiped with a low-cost chinese filament sensor which can be quickly damaged even with non abrasive filament, so I've created a simple bracket to be able to use a PTFE tube to protect it. You can use the original…
Test you bed mesh with this print. 500mm X 500mm
I designed a Z height adjustment for the 10 Watt laser on my Comgrow Comgo Z1 which is more convenient than the original bracket with thumbscrews. Print Settings Printer: CTC Bizer Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm…
I tried other models of dessicant containers meant for this model of filament dryer but none were easy or worked well. I made this model that simply slides into place and had an easy to remove lid for quick removal and refilling of…
Not sure does it really works, but at least it blows the laser smoke away. Any tips and suggestions are welcome. Fits a normal 6mm OD tube. I will add the “angled” air input version later. Printed with ASA, 40% infill, 4 perimeters but…
This is an assembly corner if you are missing one or two from the Comgrow 3D Printer Enclosure Fireproof and Dustproof Tent for Ender 3/Ender 3 Pro/Ender 3 V2/Ender 3 S1/Ender 3 S1 Pro, Constant Temperature Protective 3D Printer Cover…
…Please be sure to hit like & post a make, I'd love to see your prints! Improve cooling & greatly reduce printer fan noise! Use with M3 heat inserts 8-12mm Bolts & M3 T-nuts. Longer M4 bolts needed for the fan. Used 80mm Noctura 12v with…
Just print, glue up the original silicone brush and screw the bracket in place reusing the 2 carriage screws. compatible with COMGROW PEI https://a.co/d/ekneZyG
Hello! I designed a better flowing Fan shroud in order to allow better Air flow around the heat break and MCU USB board. Designed to be printed in place face down with no supports., Infil depends on how heavy you want the shroud to be.…
…Please be sure to hit like & post a make, I'd love to see your prints! T300 Rigid filament sensor mount with & without CAN cable mount Use M3 Heat inserts
I got a pair of Comgrow filament dryer boxes and found that they don't display humidity unless they're actively heating. I am storing some unused rolls with tubes of desiccant beads inside them and want to be able to glance at the…
Since Comgrow T300 heat bed cable transmit the AC current, it is better to protect it. Mine had some minimal (but visible) damage during packaging, so I decided to protect it a little bit better. I printed mine from TPU. I used supports,…
Simple mount to attach the Comgrow filament dryer box to the Neptune 4 Plus. Keeps filament dry, shortens the feed path, and saves space by lifting the dryer off the table. Held in place using the stock spool holder—just insert the spool…
Air Assist for a Comgow Z1 10W Laser. Fits on the original Housing. You need: 1x V6 Nozzle drilled to 1.5mm 1x KJH04-M6 2x M3 Screw 8-10mm Edding to darken the V6 nozzle. Works very fine.
I created a shorter version of the original box wedge from ZerOz. It allows me to get even lower humidity levels.
This is a 65mm spindle/router mount for the Comgrow Robo CNC. It will fit the Makita router that is commonly used for larger CNC machines. It uses 2 of the lead screw nuts listed below. You may need to tweak the tightness of the top lead…
Adapter to use Bambu lab hotends on a Comgrow T300 You'll need: 2 M3 inserts 2 M2 inserts 1 small piece of PTFE tube 2 M3 x 20mm screws You may need to tap your hotend heatsink to mount the fan The M3 screws that hold the hotend go in…
This is a fast and dirty 52 mm spindle mount to be used with the included aluminum clamp to help with heat dissipation. This was remixed from Aurora Techs mount. If you haven't checked out her YouTube channel , you should! FYI, I removed…
…Please be sure to hit like & post a make, I'd love to see your prints! Use the T300 without its grey plastic extruder cover. Use with M3 heat inserts.
Model is .2mm tall, and the lines connecting the points are .4mm wide.
Crank wheel for the Comgrow ROBO CNC router Printed in PLA or PETG 3-4 perimeters 0,2mm layer-height 10-15% infill Additional parts: 1x M4 x 40mm screw 12x 3mm x 10mm sheet metal screws Montage and installation video: Handrad für die…
Comgrow T300 Camera Mount Update : 5/11/2024 - I have been using this for almost 2 months and I have had no issues. It puts the camera in a place where I can see the nozzle and moves with the z-axis so I can watch even the tallest prints…
…Please be sure to hit like & post a make, I'd love to see your prints! Upgrade your T300 Printer to a BTT Manta E3 EZ & CB1 combo to use 5 drivers! For use with my T300 Bottom cover mod.…
The Sovol / Comgrow SH02 filament dryer has been deservedly criticised for inadequate venting and noise. I have attempted to improve both. The design shown should be self explanatory but don't attempt it unless you are prepared to drill…
Most of the Air Assist designs for the Z1 are set for the focal length of the 10w module. I'm not sure how badly the 5w actually needs a proper air assist, but getting the smoke away from the lens is always good, and this is pretty…
Print with flared ends on the print bed. Using a brim is recommended.
This model will replace the stock laser shield on the Comgrow Z1 laser. There is no loss in work space as the supply tube runs through the rear of the laser mount and It is the same length as the stock shield so it can still be used to…
J'ai apporté quelques modification au caisson en toile Comgrow. Le support pour le bandeau de led est plus compliqué car il faut trouver la cornières de 25mm, c'est une chute que j'ai trouvé à Leroy Merlin. Pour le reste, il faut un…
A simple way to attach a hygrometer to your filament dryer. I noticed the accuracy was not quite right on my dryer so I added this as a second check.
This replaces the original shroud on the Comgrow Z1, and is the same height as the one used for 10 watt Z1. The top plate mounts with the same screws that hold the original shroud, and the nozzle section attaches with 6x2mm magnets. This…
I were really enjoyed coloring my prints with Sharpie markers using Color blender design by Devin Enrique ! So I made an mount for my Comgrow filament dryer box (Also released by brand SOVOL) that makes it possible to attach this sharpie…
There is room to secure a 6mm timing belt around the knobs to help keep the gantry in sync when the printer is in a powered off state. There are also numbers to help you adjust the sides individually if need be.
This is designed to hold the spool directly over the gantry with a 1" rod or dowel. Threaded rod is also viable.
Hey up everyone, here is my latest design for on top of printers. This will fit on any 20 x 20 V-Slot Printer like CR-10 or Ender ETC. This was designed sepcifically for the Comgrow Filament Dryer Box link is https://amzn.asia/d/2g327nx…
…Please be sure to hit like & post a make, I'd love to see your prints! Add a shutdown Pi or any other function you wish button to the side of your printer. With or without HDMI cable access hole. HDMI VERSION USE WITH THIS SCREEN MOUNT!…
The original wires are a bit short. I changed my USB cable to a slightly longer one (USB-C to A). and I had to extend the 24V power cable ( by solder or if you have the apropiate 2-pin extension cable).
Print with the long face of the bracket on the build plate. No supports required.
…Please be sure to hit like & post a make, I'd love to see your prints! Add a BTT HDMI5 Touchscreen to your T300 Printer. For use with my Manta E3 EZ mainboard upgrade!…
though it may only take a few minutes to print it does an important job, keeps your filament dry
The outrigger allows different types of cameras. The holes should be wide enough for a standard camera screw. Clip to the upright, bolt your camera to the flat or otherwise be creative. It's long enough for a wider camera to have a clear…
Extends the roller to accommodate large 5kg rolls. Should still be compatible with most rolls on the market. Added a bearing distancer if you want to tighten the original bearings without adding friction. Be aware, I removed the bearing…
This adapter has an outer size of 10cm and an inner size of 5cm. Fits exactly on the Comgrow Enclosure to remove the air through a ventilation system. For a smooth thread, a little grease can be used. I would like to see how other people…
LED Light bar arms for the Comgrow T500 printer for use with U-Shape Aluminium Led Profile. I used the LED profile from here, which includes the clips as well as the filter: https://amzn.to/49yAkll Uses two of the screws from the top bar…
My T300 had a design flaw that enabled the bed heating cable to come contact with the sharp edge of the Z-tower aluminium support. As quick fix I taped the cable to the frame but to have some long term peace of mind I designed these which…
Lost the nut for the filament feed out of the dryer. I tried other supposed M8 models but none worked. So I made my own. Printed in PETG at 0.1 mm layer height and 100% infill. Included the FreeCAD design file. The important adjustment is…
I purchased my Sovol SH03 dryer and noticed that there are vents on the bottom and was not happy with those being so close to the table. I also found about a dozen SH02 models for risers, but found none for the far beefier SH03, so I…
Using the original cable as a template with the two positioning rails facing you. Solder or wire the cables like this: BLUE - GREEN - RED - BLACK The original harness is all black, but transfer one wire at the time. Note that the two…
Allows connecting a Prusa mmu3 up to a Comgrow dry box with the provided bowden tubes.
Bracket for simple mounting of laser to mini CNC machine This is mounted around the 52mm CNC spindle and laser attached with the (included with the laser) mounting bracket hook I printed in with 100% infill to ensure it is sturdy (and it…
Ficher crée pas Z.Rogers Filament PETG - ABS - ASA Tuto: https://lizati3d.com/remplacer-la-tete-dextrusion-de-la-comgrow-t500-par-le-biqu-h2-v2s printer.cfg
Simple vent open/closed. Place one at the front top and one at the bottom back to ensure airflow threw the spool. Set the airflow depend of your moisture level.
With the original mount of the Comgrow 10W diode laser, if you had a tall workpiece you had to completely unscrew the thumbscrews and move them to the threaded holes on the other side of the mounting plate. I also didn't like having to…
Should fit any fabric enclosure with a 8.5mm diameter frame. items needed c920 webcam use mount created by maxdeangelis https://www.thingiverse.com/thing:4138414 2 m3 voron heat inserts 1x m3 x10 screw 2x m3 x8 screw enclosure with 8.5mm…
…Please be sure to hit like & post a make, I'd love to see your prints! Add an external WiFi antenna to your T300 & flip the Ethernet socket the right way up. Be sure to check out my other T300 models.
This is a shim for the dual filament dryer from Comgrow (see picture). It should also work for Sunlu as I believe it's the same dryer with a different badge. This allows moisture to escape from the box to help dry the filament. There are…
…Please be sure to hit like & post a make, I'd love to see your prints! Add Canbus to your T300 using a BTT EBB36 CAN board & my Manta E3 EZ mainboard upgrade. replace original toolhead breakout board with this.…
Tired of your Comgrow dryer scorching the table? Raise your dryer to stop a fire with these little feet! You get a bigger rise(15mm) to disipate that extra heat plus a nice wide base and if you print it out of TPU like I did, it will…
Very crude solution to the problem I was having. I did not want to keep having to use whatever I had available to keep the lid lifted. So I threw this together after I was unable to find something I was happy with here on Printables. The…
Comgrow sh01 dryer ptfe grommet. This one will test your print settings. Prints in TPU. If your settings are off you can scale it a few %. Pulls through from the inside, PTFE is friction fit just push it in. I printed with .6 nozzle and…
A three-part air intake to be used with a Comgrow laser cutter cover. This allows good intake air to come from the front right of the enclosure and get pulled across the laser bed to the back right exaust port. Allowing the cover to be…
print each half, and slide together to hold the dryer box top side of ramp is open end with display printable on ender 3 220x220 table link to congrow dryer box on amazon here https://www.amazon.com/dp/B098D366R3
Quickly devised model that is in my daily use as mount for ERCFv2 to my Comgrow T300 printer from sovol. Mounted it on 90 degree angle to get the drybox next to the printer. Mount is mounted with standard screws and uses these models…
I use this on my current setup. V2, made oval of the mounting holes to make tolerance. You need m3 heat set inserts.
Following Mark's Spool Adapter Guide, I created an adapter for the Comgrow Spool. Scad Settings:
This simple design of a dust collector for the Comgrow Robo CNC fits around the mounting block of the z axis step motor. There is still some work in progress as with the vibration the collector moves a bit up. I have created a possibility…
I attached my CANVAS upside down to the rear of my 4 spool Comgrow dryer. The PTFE tubes would pull into the dryer and also wanted to help support the PTFE tubes, I have the original design on the CANVAS as well. For printing, lay on…
Comgrow T300/T500 PTFE Tube Filament Feed Adapter Adapter for the Comgrow T300 or T500 that routes filament to the toolhead via a PTFE tube. Designed to work with ECAS04 push-fit connectors (without the black rubber gasket). Note: The fit…
I recently upgraded my Tronxy XY-2 Pro with the Comgrow Ender 3 Direct Drive Extruder Kit. This kit is currently selling for $50 on Amazon: https://www.amazon.com/gp/product/B0CRKS7XK9/ref=ewc_pr_img_1?smid=A2ALB3RMNIRLH8&psc=1 This kit…
Ce conduit de refroidissement personnalisé améliore le flux d’air autour de la buse pour la Comgrow T500 équipée de l’extrudeur Biqu H2 V2S . 👉 Le support intègre un positionnement optimisé pour le probe de nivellement automatique (type…
Bonjour, Voici un remix du support de caméra personnalisé pour une caméra du type NORTEC Full HD 1080. je conserve la semelle en l'emboitant dans une rainure. Un clamp avec une vis M4 x 12mm permet d'abloquer la caméra. j'ai repris la…
I only use my Comgrow for one dedicated filament at a time. It is on a riser in the back of my setup and I needed a 90 degree angle mount to see the readings so I created this. I tried several threaded designs but ended up just going back…
This is a mod for the Z axis to add a cheap Amazon Mister. I am using it for Air Cooling on my Robo. The V2 version will work with the stock spindle and a 52mm mount as well. The V2 will also work with my 65mm Makita router mount, simply…
Got tired of pushing my Comgrow dryer boxes power brick off the table so i decided to do something about it. I designed it to be able to be wall mounted with either double sided tape or a screw. The screw hole is not counter sunk as of…
I replaced the print head on the T500 with a custom setup so that I could have a better hot end and extruder. I didn't like where the induction probe was sitting in the new setup and I wanted to be able to adjust it so that it was exactly…
This is a quick and dirty atachment for the Prusa XL to have the fillament dryer directly atached to the 3030 rails. The STL is for the right side, mirror if you want it for the left side and want to use it with the power supply below.…
Two months ago, I upgraded my Anet A8 Plus with a Sovol SV06 extruder. That upgrade has worked so nicely for me, I wanted to upgrade a few of my other machines similarly. Rather than to upgrade another machine that's already equipped with…
Comgrow Z1 Pro 20w Laser focus block got lost, so I made one for the sizes published in their document. Print with any filament and any infill. It just needs to stop the laser head at the right level.
Flange/Reducer Fills the gap between the included Comgrow flange and hose for the Vevor Fume Ext. XF180 (May Fit other Models).
Printer: Ender 3 s1 w/Sonic Pad & Ender 3 V3 Material: PLA Print Temps: 205 & 70 Nozzle size: 4mm Layer height: 2mm (Good Quality) Speed: 100mm p/s Supports: NO Bed Adhesion: NO This is a very simple Bearing Axel to be used with the…
Avantages : Assemblage simple sans colle (vis M3/M4 + insert en laiton). Fixation solide sur le châssis (côté droit). Meilleure visibilité et ergonomie que l'écran d'origine. Imprimé sans supports (ou minimal selon orientation). Pièces…
I was getting my timelapse messed up from the light on the comgrow dryer. It also doubles as a holder for the lid. Double win. Hopefully it helps you out, if it does, let me know with a like and a post! Happy printing!
The mount uses existing holes on the X axis gantry where the thin metal cover is mounted. The camera is an inexpensive DIY camera from amazon. The camera holds well to the mount without a fastener, but you can use a small screw to attach…
This is a custom-designed, 3D-printable handle for a Comgrow PEI build plate. I designed the handle in Onshape and printed a prototype to test the fit against the original metal plate. The design uses two separate printed pieces that snap…
Never had any luck with the auto z alignment/leveling on the comgrow t300 so i made these simple little blocks to set the z gantry level
