Liczymy pasujące modele…
Simple and easy to print filament waste bin for QIDI Q2. Unlike most other models does not require any additional hardware (magnets, screws, adapters, etc.) to mount. The hook/latch design relibly holds the bin in place while still being…
This waste box brings rolls the purge material to the front (as original model) but also added a drawer to make simple the emptying of the box without moving the whole box. It can be important, if you do not have much space and you want…
2mm thickness 330g with 0.2mm layer and tree support narrower≈290g for narrower one, I strongly recommend to use support enforcer as shown in picture I uploaded
This is a clip-on poop chute/bucket for the QIDI Q2 , designed to collect purge material neatly without any screws or permanent modifications. UPDATED Small Version (RECOMMENDED PRINT) : Added Chamfers to improve Printability Added Holes…
Riser with vent for the QiDi Q2, this is found on the QiDi Wiki page, but I am uploading it here so it is easier to find. Prints easy, I used .2 LH and the “.2 strong” setting. I use automatic, normal supports with the stock settings set…
Support All my designs and mods on Printables are free to use and remix. They have a non-commercial license. If you enjoy this or any of my other designs you can send me a small donation using the link below. Thanks :)…
Spacer for stable TPU printing for the QiDi Q2. In the stock setup, there is a 2.6–2.7 mm gap between the front wall of the feeder housing and the drive gears, where soft TPU filament can sometimes slip out. With this spacer installed,…
Qidi Q2 — Performance Cooling Duct (v5.1 & v6.0 Dual-Flow) Summary A high-efficiency part cooling shroud for the Qidi Q2 . This duct was precision-engineered using CFD (Computational Fluid Dynamics) to reduce turbulence and provide a…
Print with 3-4 perimeters for strength and use the orientation it imports in as no supports are needed. I’d recommend PETG, PCTG, or ABS since they are more flexible than PLA or ASA and more forgiving of tight tolerances. You may need to…
20-5-'26 Update If you have a Pheatus Conch hot end, there is a new model upload for it of this duct. This will fit without having to force the Conch hot end behind the original duct in this upload. You can find the new Conch version here…
Hierbei handelt es sich um einen zweiteiligen Filamentabfallbehälter, bestehend aus einer Rutsche und dem Behälter. Die Rutsche setzt sich aus zwei Teilen zusammen: dem Hauptkörper und dem Deckel, die nach dem Druck einfach…
Like many other users of this printer, I also did not want to scratch my top clear panel with the ptfe tube while printing. This model is designed for a newer revision of the Q1 Pro (The one with the bed endstops) since I believe the…
This filament cutter was originally designed for the Qidi X-plus 3. Although I don't have an X Max 3, others have said it works perfectly. If you have the Smart 3 let me know if it fits. No more disconnecting tubes and reaching for snips…
The lid prop angles the top glass creating a “chimney effect” to vent the hot air. With my 50mm versions of the lid spacer, you no longer have to print PLA with the door open. The original design was very narrow and made the glass lid…
This is a simple but functional dual purpose clip designed for the PTFE tube/push fitting on the Qidi Q2 toolhead. The clip acts both as a locking clip to prevent the PTFE tube from being removed and it also straightens the PTFE tube to…
Small support with a hinge. It can be permanently attached to the grass handle and being easily used to support the glass (PETG is preferable material) Printing tip: Print it using PETG, in the vertical position showed on the picture and…
A design for mounting a Beacon3D H Normal probe onto the tool-head of the Qidi Plus4 Update: 10th April 2025 I have uploaded an M3 screw variant of the mount for later model versions of the Plus 3 that use M3 bolts instead of 2.5mm…
This is a simple print that allows you to cover the rear slot in the back of the chamber. This seals the chamber up even more and blocks the air coming from the mainboard chamber. Helpful when you are running the mainboard 80 mm fan mod .…
Qidi Plus 4 Rear Cover with the choice of different fan sizes in 60mm, 80mm, 92mm, 120mm Printer settings with ASA are with my printer. Your settings may differ from these. Material ASA (Qidi) HotEnd Nozzel Temp: 270°C Bed Temp: 105°C…
Stock cooling duct on the Q2 is very imbalanced and the left side suffers from poor cooling as a result. I designed this duct and fan mount to correct that and simultaneously improve the cooling performance. It is drastically better. It…
🔄 Update – Version 2.1 (Mesh Fix & Improved Wall Generation) This update focuses on print reliability and structural stability, especially in narrow sections of the base plate. ✅ What’s new in V2.1: STL mesh fixed by jetmech43 Many thanks…
UPDATE 11/09/2026 Someone had issues with the front cover while using the polar cooler so you should be aware that these covers were made before the polar cooler and from what I can see they won't fit without some hacking. I Will consider…
Summary Designed to fit over the Z-stepper mounting bolts in the base of the print chamber (see photo). The model is a single piece. Print two of them. Discussion When doing a platform calibration, the printer will bring the print bed to…
The plugs help mitigate heat loss below/beside the XY steppers, where there are big gaps leading to the back of the printer. Print these out of TPU, they are made to fit snug. Easy to install, flex them into place. You need to remove the…
About Draken is a high flow dual channel fan duct for the QIDI Tech X-Max, X-Plus and I-Mate (S). In order for you to use it, you need the new extruder carriage. If you don't have it installed in your printer already, you can contact QIDI…
Due to the heat issues that could affect the QIDI 3 Series tool head some clogs were redesigned to improve airflow and to reduce the hotend and tool head electronics temperature. This mod was created for QIDI X-MAX 3, as 3 models are…
V1.1: much smaller back panel cleaner model PRINT WITH ARACHNE (Orca Slicer: Quality → Wall generator → Arachne). Otherwise the thin support connectors may not print at all. ----------------------------------------------- This is a…
Discussion A replacement mainboard cover for the Qidi Plus4 that allows for the use of an 80x25mm fan This is a variant of my other honeycomb design posted on Thingiverse This variant positions the fan more centrally over the hottest…
An issue with the Qidi Q2 is that the internal PTFE filament tube rubs against the underside of the glass lid. Even worse, it scrapes across the screw heads which hold the lid's handle in place. A common solution is to print a riser for…
This spare parts/toolbox was designed to organize and store common spare parts for the Qidi Plus4 3D printer. There is also a removeable tool tray designed to hold all tools provided with the printer. You will need 6 M3 x 30 socket or…
Update 10/19/2025: Some users have noticed that some brands of desiccant granules are small enough to fit through the slots of the original design. I've revised the design with narrower slots. I've tested the revisions with several brands…
Support de bobine pour Qidi Q1 Pro. Plus solide que l'origine, et surtout placé au dessus de la machine, donc libère de la place. Version sans démontage de la base sur l'arrière de la machine. Sans vissage ni collage. Prévoir supports sur…
The underside of the platform feet isn’t perfectly flat, so the bed never references a true plane and dual-Z drift makes it worse. These blocks give a flat, rigid reference, so the platform squares quickly and stays consistent. They can…
Update: (8/21/2023) - Added new version for x-Max 3 - with spool holder mount at 90deg - note that this will position the desiccant well at the bottom ONLY if the holder is mounted on the right side of the printer. Also reduced the…
I've used some of the other risers, but they didn't flow with the Q1 aesthetic. So I rounded things out a bit and made it snap-together. The corner pieces have built in support for printing. You will need 2 of each corner and 4 of the…
Update April 5, 2021 Gripen version 1.4 released. It's just a minor fix as some have reported it hitting the motor, 1.4 is a bit thinner so it should clear. Support All my designs and mods on Printables are free to use and remix. They…
Ultimate 3D printing accessories toolbox - 3D printed. Features: Slots for allen key set from 1.5mm to 3mm with holes for magnet Slot for 6 nozzles Slot for Screw driver Slot for a number 7 wrench Slot for a nozzle cleaner tube…
Modified version of Allan's QIDI Plus4 foot to fit the Q2. This raises the Q2 1cm off your desk, and provides a wider base for stability. For my printer this increased stability and reduced vibrations. These may require more work, your…
## APPARENTLY THE FAST_START MACRO DOESN’T WORK WITH QIDI BOX. FW 1.7+ can also cause issues. Sorry. ## ## NEW in v3.5: PRINT_START_COOL to circumvent the common heat based Z issues. ## There's a lot to improve in the stock Plus 4…
This is a dust cover for the enclosure. It prevents dust and important bolts from getting in. I made this because I lost a bolt for my M3. It works better if you use double sided tape.
I came across @MARCPRUDHOMM_1986375's excellent design for an inline filament cutter designed to fit the Qidi X-Max 3/X-Plus 3 models, but found it didn't quite suit my Qidi Q1 Pro. The longer tube on the bottom of the original body did…
UPDATE: I have replaced the files with STEP so it's easier to remix as QIDI changed up the mounting locations and i don't have acces to this data. Attempt this fix at your own discretion! Only work on the heater with the power off and the…
I've got my Qidi Q2 and tools were just in a plastic bag, I've decided to store it in a box.
Spool holder clamps to handle of the X-Max3. Allows use of Qidi drybox or a regular spool. 2x M3 x 50mm fasteners are required for the clamps. These are the same as the fasteners you likely removed from the printer during the installation…
Poop Chute for Qidi Max 4 with detectable bucket. 2 Versions, one that uses the current screws to help attach to the back of the machine, and one version that does not use any screws. All new based on features from all my favorite designs…
Update due to a review posted - Please be aware you are adding 50ish mm to the top of the printer with this vented riser, the existing spool holder will not work with this model and it wasn't designed to be used with the stock spool…
This riser is designed to accommodate the QIDI Q2 glass lid. I’ve included the STEP file via Onshape to allow for easy customization, particularly if your foam tape dimensions differ from mine. Materials Used: ½" × ½" foam tape M2 heated…
If you dont know how to import your QIDI X-Max 3 to Cura, you can use the following instructions. If you already have a 3D Printer in Cura, just go to your configuration folder . Help → Show Configuration Folder Extract the files from the…
QIDI Q2 Riser I redesigned the original H3D-Himon riser because the top glass wasn’t lifted high enough — the PTFE tube was still scraping against the glass. This version increases the height by about 45 mm , giving the tube enough…
My first attempt, which was oval race-track shaped with a very shallow 20 degree leading edge still managed to catch the PTFE tube. So, I modified the design to be more inspired by cow-catchers on the front of trains. I printed it in PETG…
I don't really like the glare from the backlight on the camera of my Q1 pro. Therefore, such a light-proof visor was made. It doesn't stick out much, it's hard to touch, it doesn't obscure the image much -it works.
Very simple, easy and quick TPU strip that helps close off the back of the printer to mitigate heat loss and contribute to cooler electronics. It presses against the back panel for a tighter seal. Related Models: Qidi Q1 Pro Exhaust Port…
I found that my new Qidi Box was prone to jamming when changing filaments. The jams consistently occurred when the filamant was about mid-way through the 4-into-1 manifold in the filament hub. After some experimentation, I discovered that…
Open the corresponding 3mf file with "Open project...", select your filament and nozzle, use 0.2mm layer height, slice it and switch to the temperature tab. Check that there are multiple temperatures. --> Print and have a look at the…
A 45mm or so long duct to connect the QIDI Q1 Pro's print chamber 60mm internal fan to the vent at the back to allow hot air to escape without heating up the electronics. The original idea was based on the model below, only as I have my…
It's a simple tool to help fine-tune the bed leveling.
Overview A good starting point for the Fiberon line of filaments for the Qidi Plus 4. These filament profiles are for a .4 nozzle and are for Orca Slicer . Download Download the file normally, this should open up the file in a new tab in…
Filament Purge Bin for QIDI Q2 . Keep purges under control—whether you print multicolor or single-color with frequent filament changes. Designed exclusively for the QIDI Q2, it mounts cleanly and keeps the chamber tidy without permanent…
I have adapted the original model of the Qidi cutter so that it can be used for the Q1 Pro. There is already a version from "scottishblondie" but it sits very loosely on my printer and can slip off the print head. For this reason I have…
Are two pieces not enough? Print as many as you need. To insert the clip, you need to disassemble the desired segment of
Designed a trash container, that fits inside the printer. Print in two parts and glued together. For bottom 2 magnets 6x3mm can be used. Added a short and long version.
Have you noticed, that the printer is not working as expected? You can move the printhead without homing and it might crash somewhere. you can also move the base and its crashing if you reach the top. The reason is a not well programmed…
v2 of the cutter Unclip drag chain and remove bowden tube. Slide cutter under the drag chain slip over drag chain mount and insert bottom of cutter into bowden hole on print head. Reinstall drag chain and insert bowden tube into top of…
I designed and covered this on my YouTube channel “ Functional Print Friday ”: https://youtu.be/-XNaVkgBUEQ Purge bin that hangs off the Plus 4 to avoid it moving around and getting out of place. Cut-out to allow fresh air to still enter…
This is a newer ‘drop that can snap onto the input port of the printhead, and has a bevel on the input side of the elbow to ease install of the PTFE tubing. Note it’s intended to be a firm grip on the process so the tube doesn't easily…
Wall thickness is 2.25mm. I run a 0.6mm nozzle with a 0.75mm extrusion width, so it worked out to three passes on my setup.
I've designed a solution for my Qidi Box and Qidi Plus 4, integrated with a Sunlu dryer. Y-splitter allows all components to work, and eliminates the need for frequent reconnections. Please look for pc4-m6 “through” type, for reference…
Hat that reduces the glare from the Led light above it. You can see the quality difference between with and without in the images. Regarding the camera, It's the official camera by Qidi on presale can be found on the official website.…
QIDI Q1 Pro electronics air flow can be improved, this mod was created to add 80mm 5V, you can use 24V using parallel power splitter using the stock fan, fan holder. If you use 5v, much quieter and enough air flow, you can connect the 5V…
This simple dual bracket piece, or “fixing block” as Qidi calls it, can accept both the stock spool holder and the hub for the Qidi Box that would normally take up the spool holder spot. Now you can attach both at the same time! It works…
Designed it to keep desiccant in place incase of removing it from Qidi Box Compatible model can be found here https://www.printables.com/model/1386559-high-capacity-desiccant-bin-for-qidi-box and with smaller holes…
Here is a duct for the Qidi Plus 4 to connect a 4 inch dryer hose to the air outlet port. No need for screws or glue, the model clips into place, insert and twist clockwise to lock. If you are lucky enough to have a window close to your…
This is a replacement glass door handle for the Qidi Q2. It is much larger (while still looking nice), making it significantly easier to open/close the door comfortable. Uses the screws & bushings from the original handle.
All in one. Print in place. Qidi Q1 Pro bed leveling tension knob v2. Every inside tick is 2 minutes. Every outside tick is 2 minutes. Total of 60 minutes. I've also updated the screws_tilt_adjust macro so it probes a reference point in…
Samsung Galaxy Z Fold 7/8 Ultra Wireless Charging Dock UPDATED - Fits the Galaxy Z Fold 8 Ultra also. I love my Samsung Galaxy Z Fold 7, but I couldn't find a nice charging dock that would allow me to charge my phone in the “unfolded”…
Update April 1, 2021 Added a version without filament guide. Use this version if you just want to cover the hole in the top cover: qidi-xplus-xmax-top-cover-no-guide-1.0.stl About This is a remix of Elmagnifico666's excellent "Qidi XMAX…
This model is a large capacity desiccant vessel for the Qidi Box. It's best filled with a funnel or chute with one of the side plugs installed and before installing it in the printer. It keeps the box much dryer than the original packets.…
Ready to print in the Q1 pro, please use Orca from 2.0 RC comes with the Q1 pro profiles ready I use ABS but you can use PLA+, PETG, or ASA too. please be sure to make the skew correction first and flow calibration look this model XYZ…
UPDATES 11/14/2025 Version 1.11 Made a version of the cooling duct for the more common small mouth 5015 fan. Added a honeycomb version of the cooling duct bottom panel. Also removed the curved wall on the inside of the fan area for the…
Designed a magnetic frontcover for the printhead, that can be used with the original Printhead without further modification (adapter required) and a version with a new base plate. I keep the original style and dimensions as good as…
Update October 9, 2021 Design updated to fit the newer carriages (untested) as well as the old with the small 30 mm fan. Support All my designs and mods on Printables are free to use and remix. They have a non-commercial license. If you…
Update 24/03/2026: tighter M10 threads Update 15/02/2026: PTFE passthrough PC4-M10 version (untested) The original model clip-on works really nicely so I wanted to use it. Also I wanted something simpler (although I might built the…
I have noticed that the wires of the print head are rubbing against the case of the printer in the back, when printing big parts. I have created this ramp that will help the wires slide up so you have less wear. Print in ABS or ASA. I…
Here is a set of covers to plug the unused holes/ports behind the printer and make the print chamber a little more airtight. The model was designed to be printed in PP (Polypropylene) and designed to take into account a post-printing…
I designed this spool holder for QIDI printers because the original one, when used with cardboard spools, often created too much friction. This could lead to false filament tangle detections and also generate annoying noise. After…
Build plate holders for 280mm x 280mm build plates. Primarily made for the QiDi Q2 but can fit any other build plates of similar size. Recommended print settings: PETG 3 walls 10-15% infill 5 bottom, 5 top layers You can print this on the…
Update 22.12.2024: ---- Update the models with the the bump to avoid the self rotation and add the STEP files for the original fan. ---- The airflow is much better than before, so try it out and please give feedback. I have use it for…
Stock camera configuration in QiDi Q1 Pro 3D printer causes unnecessary image quality degradation because of LED light falling directly to camera lens (at least if you have the same Q1 Pro version as me, because I can see that QiDi…
Improved Qidi Box Desiccant Bin – Reduced Hole Size + 3 Variants This is my remix of the awesome silica gel holder originally designed by @R985_3546396 . His model works great and fits perfectly in the Qidi Box — but after printing it, I…
This is the third, and hopefully final revision of a set of vented lid riser pieces for the Qidi Plus 4. This model reduces the weight of my earlier models, and tightens up some of the larger dimensions for a better overall fit. Depending…
A simple holder for the Teflon feed tube to the extruder chain. Prevents chafing of the top cover. I printed from petg 0.2 layer height, 0.4 extrusion width
This adapter is designed for the QIDI Box, which is a multi material system. Some filament spools—such as SUNLU rolls with a diameter of only ~195 mm—are too small to rest properly on the front and rear rollers. Instead, they sit on the…
Stínítko kamery pro QiDi q1 PRO - odstínění svitu z osvětlení uvnitř komory. Vytištěno z PLA - zatím mi drží, ale rozumnější bude např ASA, nebo jiný teplotně odolnější materiál, neboť q1 PRO má vyhřívanou komoru, až na 60°C. Materiál -…
I wanted a nice solution to catch the printer poop on my new Qidi Plus4 and this is what I came up with. Hope you like it and maybe it can prove useful for you too! I used generic pla and the 0.20mm strength profile on my Qidi. Painted…
I wanted to create a filament savor for the Qidi Box that doesn't require using any double-sided tape. I used ASA GF for mine. Materials needed- m3 Heat Set Inserts- 2 per filament savor m3x6mm socket cap screws- 2 per filament savor PTFE…
Update February 10, 2021: Version 1.3 released. Changes: Removed fan guard for extruder fan as in some cases the guard increases the noise level of the fan due to back pressure. This should also increase performance a little. Two new…
I have created this fan duct to improve cooling. The air is now swirled directly below the nozzle, providing effective cooling where needed. Overhangs up to 75° are possible instead of 50°, and printing bridges and supports has also…
UPDATE: Added a 1mm more clearance version. UPDATE: I have added a model for a “regular” 5015 fan. This model has internal ducting to help with the small fan outlet. UPDATE: Added 1mm more clearance version to "regular" 5015 alternative…
This model and associated optional configurations are the result of months of trial and error work to improve the chamber heater behaviour of the Qidi Plus 4. The stock chamber thermal probe is located under the frame rail to the…
![Larger Qidi Plus 4 Lid Spacer [Updated Size and Shape]](https://media.printables.com/media/prints/1053720/images/8192105_e4d6d9ae-eb33-4d51-a963-1ef8a95607aa_4493d5d3-f08e-4035-abf2-1d4f4315463e/20241122_163022.jpg)
