Liczymy pasujące modele…
I got tired of my ribbon cable dragging across my bed and prints so I made a cable clamp and top fixture to suspend it. I just added a piece of shock-cord with beads both ends as toggles. The clamp is a tight fit and needs supports on the…
This adapter allows fitting a spool rewinder to the SV06 or SV06 Plus, which stops a lot of problems with tangles , also check out my other mods for SV06. I have designed the models specifically for SV06 , SV06 Plus with easy mounting and…
This remix adds M2 hex nut slots in the bottom. Using M2x12 or longer screws you can raise the lid to adjust fit and tightness of the z-coupler inside the frame. I made this remix as my SV06 Plus' z-coupler did not fit inside the original…
you can connect the knomi on any usb port from the motherboard just use the 5v and ground also the uart port can be used here is the motherboard diagram Later Edit 28. November 2024 modified the Knob and the Knomi holder. made them a…
Please before attempting to print this files. Print the Tolerance test from Orca slicer and be sure you can go up to 1, or the one we have made Here you can download the Toolhead for this Project that is the same for SV06 and SV06 Plus…
To be used with STL file SV06 Plus Filament Holder w/Guide and Retractable cable holder ➕ ・Template to download and 3D print・Cults
This is my rendition of a clip on box to mount a BTT Pi v1.2 board onto a Sovol SV06 printer. The box was extruded out of PLA and the clip out of PETG. I originally planned on using PLA for everything, but there were reports in the…
Hello, This is a self designed Mount for the included tweezers, clipper, sd card reader as well as a printed bed scraper and a pair of scissors. The bed scraper is mounted using a nail, for which i created a slide mechanism. Happy printing!
Printed in PETG Nozzle Ø 0.4 Layerheight 0.25 support needed for cable entries and usb cutout 16 x M3 heatinsert L:5.7mm 2 x 4010 axial fan
This model was created specially for using with Volcano nozzles, but it works just fine with original (proprietary) sovol nozzles. NOTE! You need to extend the cable for about 30-40mm so it reaches the connector It is recommended to print…
Modified to remove the bottom corner edge to provide more clearance.
MECHA SERIES This models is a part of my MECHA series of main SV06+ Components. Z-Axis Blocks Custom Z-axis blocks, supports oldham couplings on the bottom or stock configuration on the top. Uses M3 heat-set inserts (henceforth referred…
Remix to move the sensor to a higher position on the printer. Added cable tunnel with Print Bridges that can be removed after printing with a sharp knife. (see pic) Added Trimmable Print Supports on bracket angle that can be removed after…
Every mount for SV06 Plus that I've found was for the original 23.5mm nozzle. As I've switched long time ago to the shorter V6 type volcano nozzle (21mm), the Eddy probe was sitting too low. Decided to remix Chinchill's design, as it…
This is a small bracket I made to replace the filament spool holder on my Sovol SV06 Plus. It has physical threads for an M6 fitting. Print in place, no supports. Reuses original screws for the filament spool holder.
A simple snap-on light holder for the SV06 Plus Ace . You will need to edit the model in a 3D modeling software to fit your light! I recommend adding mouse-ear brims to the ends of parts likely to peel from the bed. I also recommend…
I decided to develop extended legs for the printer, suitable for mounting V-slot, to simplify the installation and use of the legs, you can install the legs without disassembling the printer, it is enough to insert each stop at an angle…
Lazy feature addition remix, added a place to insert the foam cube for storing declogging needles included in the SV06's box. Also includes printable scraper that fits the tool tray, in place of the included metal scraper. If you are…
Important Notice When attempting to upload the latest Blender file I get a parsing error on the Printables webpage. Thus the file on here will be out of date until this gets fixed. The STLs on the individual models will still get updates…
MECHA SERIES This models is a part of my MECHA series of main SV06+ Components. X-Axis Carriage Custom X-axis carriage, takes inspiration from the Monoblock Carriage by @SilencedFros_2044064 . Improved to fix some minor annoyances I had…
A filament cutter for the Sovol SV06 ACE and Sovol SV06 ACE Plus. Useful if don't won't to do tip forming when using a multi-material system like 3MS, BoxTurtle or ERCF. You need a blade from a cutter (9mm x 18mm) and a rubber band. You…
While I REALLY like the Sovol SV06 planetary gear direct drive extruder, and have adapted it to several other machines, a few of the stock parts that ship with SV06 toolheads and that are available for printing from Sovol's GitHub for the…
Front panel with original fasteners and added holes for M3 soldered bushings for attaching any parts you need. Using this model as a basis, you can easily implement your ideas for printer upgrades. Передняя панель основания с…
Stl modificado de diseño NAUTILUS. Sin tornilleria extra necesaria. Solo los mismos que ya ocupa el anterior ducto Tambien adjunto stl de prueba de overhang.
Tinker-cad helped me change configuration just enough to use the clamp as a TPU guide. no need to move PETG out and still run TPU. Printed in PETG
Cover grill / airflow deflector for Sovol SV06 Plus & SV06 Ace Plus Larger PSU fan cover designed to improve and redirect airflow, helping to prevent uneven part cooling across the build plate. Designed for 92 mm fans with a mounting hole…
This is a revamp from the original .STEP file from SOVOL's official GitHub, which was poorly organized and inconsistently translated. I've cleaned it up by grouping and renaming all components for easier navigation and more convenient use.
The support attaches to the holes of the spoolholder with the original bolts. If you want to use this i suggest using a teflon tube to do a reverse bowden setup, i printed this to do it: https://www.thingiverse.com/thing:4855279
Filament runout sensor cable holder for the top bar. Includes insert for 8x2 magnets, though they are not required. I recommend printint out of TPU.
This is a custom enclosure modification for the Sovol SV06+. The model extends the original housing to support additional hardware and improved modularity. It was designed with a focus on practical usability, clean integration, and easy…
Motherboard housing for SV06 Ace (should be compatible with SV06, SV06 Plus and SV06 Plus Ace, but untested! ) with room for a 120mm FAN. Installation: Install the back of the housing to the extrusion first using washers between the…
Based on https://www.printables.com/@SmittyForge_1090939 SmittyForge's great model.
I remixed the Sovol SV06 ACE Mainboard cover from @TheBear_3113750 and the High-efficiency fan-grill from @Noctua to one Model. Note: I remixed the Standard version of the Sovol Mainboard cover with M4 inserts. Original models:
Sovol SV06 ACE - Meanwell LRS 350 cover Another design of a Meanwell LRS 350 cover for SOVOL SV06 ACE. I tried matching the orginal design from Sovol, for better optics. You can use the orignal screws from the stock powersupply.…
This is my take on Ball joint mount for Sovol SV06 Plus/MK4S Camera module. To get the parts together I used 2x M4x10 screws with nuts (M4x8 would probably fit better but that is only cosmetic modification). I printed mine because it was…
DUE TO SPACE CONSTRAINTS, I COULD NOT USE THE FACTORY SPOOL HOLDER, SO I MADE A NEW ONE. MOUNTS TO THE REAR. DOES NOT INTERFERE WITH Z AXIS. HOLDS 1KG SPOOL WITHOUT ANY ISUES. THIS IS FOR SV06 PLUS, SHOULD FIT SV06 AS WELL. LOWERS…
Update 12/13/23 I have a new model that uses 8 m4 heat set inserts and 8 m4x20 button head screws . I have also included the step files of this new model for modification if needed. Enjoy! Original Post I keep having to re make cheap…
Have an SV06 but not enough desk space to add a standalone dry box? This dry box mounts to the top of the SV06, can fit all 1kg spools, and still stays within the SV06 print volume. Interlocking lip design and snap pins ensure good seal.…
Filament motion sensor. Erkennt Verstopfungen sowie wenn das Filament zu ende geht. Benötigt wird: 1 Kugellager 608 ZZ 1 optischer Endstop 1 Bowdenkupplung M10 Optional zusätzliche Bowdenkupplung M10 2 Schrauben M3 15mm Zusammenbau: Lager…
I saw that a boden tube adapter was made, but I always thought it was odd to have a run out sensor at the top of the printer. when you got about a 1' zone that the printer will never know its missing filament. Printed on Pla at 1.3 wall…
I've been using rogerquin's most excellent spool holder for the Sovol SV06 (Plus) . I wanted to make the grip easier and compatible with any of my spools, so I made two changes to rogerquin's original model. First, I combined the spool…
A spacer for the Klipper Screen mounting bracket. Fits Sovol SV06 and SV06+. Attaches to the original bracket with one M4×20 Screw.
Tool holder for the right Z cap of the SV06. (Can be mirrored for left cap)
I wanted to rotate the knob for the extruder on the Sovol SV06 faster, and I didn't like the versions with handles because they were too loud. So, I designed two knobs that can be rotated traditionally and with one finger inserted into…
This is a replacement print for the Sovol SV06 Plus x carriage. The model comes in 3 parts and does not need glue to be assembled. Update 24/2/10: fixed a small error in the back carriage file (bearing constraints were missing).…
Please see the original model for description regarding the Stealthburner mount. As for the Klackender probe and how to use it, you can find all the instructions here: https://www.printables.com/model/332025-klackender-probe I can not add…
The ERCF Smart Filament Motion Sensor is neat, and I wanted to mount it on my SV06. To this end, I designed a mount to attach it to the extruder assembly, taking advantage of existing screw holes. I replaced the original 2x countersunk…
Note : I haven't printed it yet myself, will update it by the end of April 24 Double-check the plexiglass dimensions before ordering, since I haven't verified it yet. Print instructions: Stop print to insert hinges on the Bottom Corners.…
Filament Spulenhalter für den Sovol SV04 (passt auch auf den SV06 und vermutlich auch auf weitere Modelle). Hier werden die Spulen mittig festgeschraubt und drehen sich somit gleichmäßig beim Druck. Ich Teile für Spulen bis ca. 75mm…
The remix is based on and thus all design credit for the original of AllTheHobbies' Filament Guide . I made the front gap wider so a PTFE tube can pass and use it for a Reverse Bowder setup to feed filament through from a dry/storage box…
This is a replacement part that is easy to print to replace the housing for the sv06+ inductive probe for ABL.
SV06 klipper screen ADXL345 Bed Mount with protective cover
A Gridfinity 4x3 baseplate that snaps onto the vertical extrusion above the power supply of an SV06 printer. It has hangers for the diagonal pliers and bed scraper that come with the printer, as well as another tool of your choice.…
This model is used to shift the motherboard of Sovol SV06 a bit to accomodate the motherboard fan mod as well as the nautilus fan mod. When I did the Type A fan mod for motherboard (Link Below), the nautilus fan was crashing with the 92mm…
I kept touching my fan when handling the extruder, so I made this fan guard to prevent damage to the fan. Print as oriented in the stl.
A redesign inspired from Sovol SV07 BL Touch Mount by RoyMcNelly on Printables. Redesigned to move the mount and probe out of the way of the tensioner flap to allow extruder gear troubleshooting and cleaning. Designed to print easily and…
9/23/2024 UPDATE: Tested Successfully Have connected and tested now, these are working great! If using KUSBA or other USB connected accelerometers, I found that an easy way to get connected in klipper is to use /dev/serial/by-path/xxxxx…
Moved it further away from the nozzle so that the focus point for this specific endoscope (no focus control) is focused on the buildplate area right under the nozzle. Plus the rear is angled more toward the gantry to stay out of the way…
Needed a holder for a second spool on my SV06+, so I designed one. It incorporates the nut thats tightening the original holder, so unscrew the original nut and screw on this holder. Print horizontally as shown in 3rd picture to maintain…
This is my attempt at a probe for the cartographer that I just got home. I wanted something a bit more rigid than the current options, as it has to be very rigid for Cartographer Survey. I plan to add some wire guide option on the side,…
Multibin insert (1x1x1.5) to hold the tools provided with the Sovol SV06 and many other printers. Best use would be to put it in a 1x1x1.5 MultiBin shell and mount that on your wall. But it can be free standing. This is fully compatable…
As the klipper screen only comes with a right side mount, it might not suit everyone, and didn't suit me. This southpaw style allows mounting of a 4010 fan as well. to power the fan, depending on the version, there is a connector inside…
Re-mixed of the original model. Simplify the construction. Red LED is visible now.
relocate run out sensor to the top of the extruder motor
I didn't have any 35mm screws available and I didn't like the crew head sticking out. So I added a chamfered recess to fit a cap head screw. 30mm screw works perfectly.
With the original parts cooler fan removed to clear the nozzle view, this LED light improves visibility. Use 12 to 24v LED light strip. Three LED lights will be sufficient. Shared power with the extruder fan.
A stronger extruder cooling fan for printing high temperature filament. It uses a 4020 12v fan. The LM2596 board converts the extruder fan power source (24v) back down to 12v. The same 12v can also be used for powering the LED light…
This cover blocks light from the SV06 screen and enables sound sleep while the machine is printing. Might also work with other printers using a similar display. Dimensions are 100 mm x 67 mm with 80 mm ledge for easy grabbing. Features:…
I wanted to install a bigger fan in my MCU enclosure but because of my parts cooler there would have been interference, so i designed this bracket. uses the factory MCU mount and some M4 heatset inserts, and factory screws, plus…
I modeled a spacer bracket so the door would fit with other part cooling solutions as well. Link for Bracket Here the honeycomb grille can be a bit tricky to print if you are on a .6 nozzle. it will not slice correctly unless you set your…
Sovol SV06 Plus Orange Pi Zero 2W Case This is a custom-designed case for the Orange Pi Zero 2W and its expansion board for the Sovol SV06 Plus 3D printer. This case provides ventilation, protection, and easy access to most essential…
I took Avel's nice LED mount and modified it to have a horizontal channel so you can put a small COB LED and rolled it 90 degrees so it was not in the way. I spliced it off the constant 24v that feeds the 4010 blower fan since my other…
Snaps onto the top crossbar of the Sovol SV06 to hold the print head cable up and out of the way.
This design fits under the dual 5015 fan mount from @Onkel_Jupp_646317, which is a remix of SV06 Dual 5015 Guinea pig version by @SavageLau, so it might fit there, too. With the remix from @jessmarie, the cable kept sagging down, so that…
A remix of Dabal's SV06 bed aligner with a bigger gap to allow use with silicone bed spacers. The original was too close to the spacers and wouldn't fit as a result. Attach to bottom of bed using adhesive tape- I used 3M VHB 5952F, but…
This remix adds M2 hex nut slots in the bottom. Using M2x12 or longer screws you can raise the lid to adjust fit and tightness of the z-coupler inside the frame. I made this remix as my SV06 Plus' z-coupler did not fit inside the original…
PRELIMINARY DESIGN – FOR TESTING ONLY – REQUIRES KLIPPER INTRO: When moving your printer into an enclosure, it is a very good idea to remove the MCU mainboard enclosure from the printer and place it outside. The toolhead ribbon cable on…
PRELIMINARY DESIGN – FOR TESTING ONLY INTRO: When moving your printer into an enclosure, it is a very good idea to remove the MCU mainboard enclosure from the printer and place it outside. The bed cable on the SV06/Plus is too short for…
I made this simple pulley that allows yout to feed filament into the printer from below, might not work with really stiff filaments. I tried pla and asa so far and they work fine. Please note that when installed it reduces the z height by…
This is a Remix of the original model to also make space for the filament ronout sensor of the SV06 Ace. The hole on the left side is fit for a Voron spec M3 heat insert to hold the original bolt that is used to mount the sensor. If you…
you can connect the knomi on any usb port from the motherboard just use the 5v and ground also the uart port can be used here is the motherboard diagram Later Edit 28. November 2024 modified the Knob and the Knomi holder. made them a…
Later Edit 28. November 2024 modified the Knob and the Knomi holder. made them a little bit smaller in some cases the bed was heating them This mod integrates the BigTreeTech Knomi V2 Display into the Y-axis belt tensioning system of the…
Later Edit 28. November 2024 thanks to our member SparksOnTap88 we have modified the Knob and the Knomi holder. made them a little bit smaller in some cases the bed was heating them This mod integrates the BigTreeTech Knomi V2 Display…
This is a mount for the BTT Smart Filament Sensor V1 for the Sovol SV06. I'm planning to do some kind of clips for the wires in the near future. Seems to work well, but please let me know if there are any problems.
This is a request from one of our members hope you like it! Print Settings: Layer Height : 0.2mm Infill : 15-20%, Gyroid pattern Walls : 3 walls Top/Bottom Layers : 5 each Notes: The provided STL files are pre-oriented and ready for…
**THIS IS STILL IN BETA, MORE TESTING NEEDED, DO THIS AT YOUR OWN RISK** **For the non plus SV06, you need to have the SV06+ Hotend or the Duct won't work** For SV06+ it should work fine without modification At least use PETG, ABS or…
XenoSix is a high-performance toolhead specifically engineered for the SV06 on Steroids project, delivering exceptional 3D printing capabilities with innovative features and precision design. While inspired by the SV06 ACE for its webcam…
Later Edit: 25 November 2024 I just realize that i forgot to add the Z strain Relief that attaches to the the X stepper motor holder! Please before attempting to print this files. Print the Tolerance test from Orca slicer and be sure you…
The stock spool holder wears down the cardboard on the filament spools, leaving cardboard dust everywhere. I didn't notice at first, but it became obvious on subsequent spools. This acts like a simple bearing to reduce the friction on the…
Simple holder to attach the Creality SonicPad to the gantry of the Sovol SV06 plus. Assembly: The left mount will be attached to the 20x40 aluminium profile using two M5x12 panhead screws (mind the gap between the profile and x-axis…
Please before attempting to print this files. Print the Tolerance test from Orca slicer and be sure you can go up to 1, or the one we have made Here you can download the Toolhead for this Project that is the same for SV06 and SV06 Plus…
Upgrade Your Sovol SV06/SV06 Plus Displays We're excited to announce three versatile display options to enhance your Sovol SV06 and SV06 Plus 3D printers. the design includes a front cover , back cover , and mount , all designed for a…
Upgrade Your Sovol SV06/SV06 Plus Displays We're excited to announce three versatile display options to enhance your Sovol SV06 and SV06 Plus 3D printers. the design includes a front cover , back cover , and mount , all designed for a…
Electronics Enclosure for Sovol SV06/SV06 Plus Upgrade your Sovol SV06 or SV06 Plus with this custom electronics enclosure, designed for the BTT Manta M4P . This compact enclosure replaces the stock housing while using the original hinges…
A 1:1 replacement for the stock SV06 Plus carriage, printed in one piece! With all the screw holes at the back retained for mod compatibility This whole design sits within the stock footprint of the stock carriage, no more compatibility…
