Counting matching models…
MASSIVE VISUAL UPGRADE FOR ENDER 3 PRINTERS POWERSUPPLY RELOCATION UNDER THE BED (IN TESTING) (Is not usable for PRO and V2) SUPPORT ME BY PAYPAL!!!: https://paypal.me/zltncsk If you woul like to see new upgrades for 3D printers, and…
Visual upgrade for Ender 3 Pro Printers Is not usable for Ender 3 and not tested on Ender 3 V2 (feel free to try it out for the V2) Support me by covering a coffee to get/keep me going! Venmo: @dannyjvj SUMMARY: After upgrading my PSU fan…
I recently installed the sliding riser with PTFE tube relocation , but I wasn’t happy with how the tube would push back out of the enclosure. It rattled against the back of the machine and sometimes even hit the wall behind the printer…
The rear suspension of my TT-02 felt far too stiff, even with the Soft springs included with the Tamiya CVAs. These brackets bring the mounting point 7mm inwards. Notes: Designed to be used with Tamiya CVAs (TAM54753) Need 4x 3x12 machine…
A wing to relocate the PTT slightly off the side of a plate carrier, holes are modeled in to fit the u94 style PTTs both single and dual downlead. Works best with hook velcro on the backside to further help secure it to the loop field on…
I needed to move the bed forward quite a bit when changing to a vzbot gantry, so I designed these rod clamps to hold the upper rod ends. Clamping style allows for easy mounting without removing the rods from the frame completely. mounts…
NEW FOR QUEST 3S! Quest 3 version here: https://www.printables.com/model/933285-oculus-meta-quest-3-stand-with-carrying-handle-for This is an Oculus Quest stand to be used when your Quest is not in use, and meant to facilitate easy…
This bracket is similar to already commercial available metal brackets on the market, with an addition of a extra hole for using zip-ties to secure the PTU-cable. with this you can move the PTU from the scorching engine-bay to the front…
I recently installed the sliding riser with PTFE tube relocation , but I wasn’t happy with how the tube would push back out of the enclosure. It rattled against the back of the machine and sometimes even hit the wall behind the printer…
The rear suspension of my TT-02 felt far too stiff, even with the Soft springs included with the Tamiya CVAs. These brackets bring the mounting point 7mm inwards. Notes: Designed to be used with Tamiya CVAs (TAM54753) Need 4x 3x12 machine…
My battery for my mini excavator isd under the floorboard of the machine. I used the kit from Amazon (shown in pic) to move the terminals to allow me to charge, jump, etc. BUT, the relocation kit is such that you can short charger clamps…
I designed this simple battery relocation for my 2013 Polaris Scrambler 850, I believe the same frame is used for 2013-2022 models and it should work for the Polaris Sportsman's as well. It is held in place by (2) 1" battery straps that I…
Redesigned model of the Y endstop mount for KW12 switch. The model "Y Switch Mount_v2.2.stl" has a membrane in the holes that needs to be cut out. Required hardware: 2x M3x8mm SHCS screw 2x M5x8mm BHCS screw Print settings: Material:…
Installing panniers rack on the Himalayan 411 often require to relocate the rear turn indicators for both visibility concerns and/or space optimization. The rack I bought from Givi didn't came with covers for the holes left after…
This modification allows the filament holder to be mounted on the side, in its original position. I made it a little thinner than the original to prevent the belt from touching the screw.
UPDATE: I have replaced the profiles with ones containing four build plates. The following versions are included: V1.0 - classic version with feeder holders that fit snugly to the housing curves, PC4-M6 V1.1 - classic version with feeder…
The original works quite well, however, the Nebula screen put it almost rubbing the print bed. So I added 2mm standoffs on the mounting side for a little additional clearance.
This model is designed to help relocate your Snapmaker U1's filament feeders to the position of your choosing. My bracket is designed to clip onto wire shelving with 30mm on-center spacing (3mm rails), but can be easily customized in your…
I mainly provide an adapter here that allows you to relocate the display of the Chitu E1 filament dryer from the narrow side to the wide side. It also includes a cover for the original mounting location and a drilling template. For the…
Due to Dragonburner modification I made stock heatbed is sitting too low (2-3mm) and toolhead is not reaching it - that is at least simple fix, just print and add spacer I made under springs before inserting them back. However there is…
i'm tired of long ptfe tubes. filament always breaking inside the tubes so i made this part to keep the ptfe tubes as short as i can you need to drill a hole in the back side as shown in the picture (the lower hole) remove the panel screw…
NOTE 3MF is Required in this model as negative parts are used Pla or ASA or ABS, it is a little flimsy as PLA but it does work, one in photos is in pla This will work on EITHER the left panel screws or the rear panel Screws 2 M3 Nuts need…
Download: https://makerworld.com/de/models/2738012-crossbar-relocation-tensioner-zero-g-mercury-one#profileId-3035756 Crossbar Relocation mit Tensioner für Zero G mercury one es wird ein 370mm Alu 2020 vslot profil benötigt.
I wanted to relocate the stock fan to have better access for maintenance. I tried many mods and designed new ones. Including TPU ducts, because every available duct deformed on the first layer of a big PETG print. Also any restriction or…
Version 0.5 patch notes -added segments for four holes -took away triangles (though the monster edition has some) This is my Ender 3 S1 (though it works with most other printers) or a filament "roller" for dry boxes. THIS PROJECT IS A…
Few people have said that the fit is snug, I would suggest scaling everything to 102% should make it a bit less snug. Currently i'm working 72hr weeks and don't have the time to get around to fixing this. DISCLAIMER: You will have to trim…
extra m3 nut and 4 or 6mm bolt are required. sensor position stays the same, no probe offset correction is required first version will fit better but it requires supports – see attached screenshots on how to place them
For installation, you have to remove the filament sensor cable from the aluminum extrusion. Pop off the top brace by removing the six screws on top, then remove the cable from the top brace. I removed the gantry from the base to pull out…
Hi everyone! I designed a Cover for my Ender 3 V3 SE and redesigned a fan relocation bracket found on printables. Both of them replace the original extruder/hotend housing for a lighter and sleeker design. You also need Vent Ring found…
Minimal PSU brackets, that allow you to mount a Meanwell LRS-30-24 power-supply completely under an Ender 3/Ender 3 Pro printer. Does not work with the stock Ender 3 power supply, but if you've upgraded to a Meanwell this will fit the…
I installed HDB handguards on my 2019 690, and it caused interference between the front brake lines and where my speedo was mounted on the Lynx fairing dash. The first part is a bracket (print x2) that bolts onto the HDB handguard bar…
I'm building an enclosure for my MK3S+ printer and wanted the power switch on the front for ease of cutting the power. I fabbed up this bracket. It fits the original switch and should fit any aftermarket switch of the same kind. I had to…
Bracket Used to Center the Filament runout sensor of the Ender 3 S1 lineup . Features 2 holes for extra Secure mounting using the 2 extra screws provided with the printer. Also has 2 holes to secure loose bits of filament.
Inspired by Voron V2.4 and Trident: Y Endstop relocation mod - model by @top_gun_de does not fit the long shaft stepper motors, so I have drawn my own in OnShape. It is as short as it can be to still fit the standard micro switch and…
for the wiper i use a small piece of silicone that i cut from a silicone workstation mat Don't forget to upload pictures of your makes I love seeing your prints of our creations :-)
Moves the Filament sensor to the top, to work in conjunction with a top mounted spool. if you remove the wire for the sensor from the harness, there is enough wire to run up the side and to the sensor without needing an extension. print…
NEW FOR QUEST 3S! Quest 3 version here: https://www.printables.com/model/933285-oculus-meta-quest-3-stand-with-carrying-handle-for This is an Oculus Quest stand to be used when your Quest is not in use, and meant to facilitate easy…
I don't want the spool in the back and in the middle of the right side. I think this original idea is very useful.
This is a rear-mount for the power supply (PSU) of an Ender 3 Pro. It's compatible with dual z-axis upgrades. It requires 2-4 M5x12 screws, an M4x8 screw with T-nut, 6 M3x4 screws, and the power plug from original PSU casing with it's…
About the relocation; I got the idea from https://www.thingiverse.com/thing:3830464 . Moving the electronics out of the cube structure gets me one step closer to an enclosed printer. Also I will soon receive the new 32-bit 4.2.7 ARM-based…
Simple holder for laying the X-gantry cable. Solves the problem of the cable being in the way. Enables better cable routing. This modifaction is compatible with the other modifactions I have provided for the Kobra 2 Max.
This module places the GPS under the front camera mount. This fits the original GPS as well as any similar sized GPS modules. NOTE: GPS modules all have different pin outs! You will likely need to change the pin order if you use a…
This print elegantly relocates the Ender 3 extruder from behind the x-axis gantry to the front. This makes the extruder easier to access as well as keeping the bowden tube fully in front of the z frame. This way, the bowden tube doesn't…
Add a power switch on the front of the Creality K1 or K1C if you don't feel like reaching into the back of the device.... I have no idea what screen the K1 max uses, but it may be the same screen. It does not use the factory-installed…
This is an assembly that moves the heated seat switches up near the shifter next to the AWC button as I wasn't a fan of the OEM location. This fits in my 2015 Evo GSR and should fit on any other year or trim (although untested). The zip…
Just a little mounting plate to relocate your Ford Bronco Badlands fender badge to the front grill so you can add that classic looking script fender badge in it's place. This fits perfectly on my sasquatch with no drilling or cutting. I…
printed in PLA, should be fine in any filament. no extra hardwear is required
Ender 3 V3 SE screen relocation with RPI Camera mount to monitor the first few layers remotely through octoprint
Simple holder for the typical SD card relocation / micro sd to sd adapter. Replaces one of the bottom end caps
A relocation plate is an easy way to relocate an axle forward of back relative to the leaf springs. The plate has a raised pin that fits into the center hole of the spring perch on the axle. Then it has one or more holes for the spring…
This original design is a really great one but I found that it was pressing against my stepper wiring a bit too tight and there was also limited room to move it around. So I added a top leg with holes that fit perfectly to use M4 x 12…
Relocate the ender 3 power switch to the front. Category: 3D Printing
The Ender 3 v3 and v3+ have 2 problems with the filament system : The supply tube can be bent when homing → could cause the filament to break The filament runout sensor moves up and down → often causes the filament to slide off the roll,…
Didn't have the build volume working to do the full size, so I cut things down to just work on the left side. Category: 3D Printer Accessories
Printed in PLA with 4 walls and 10% infill, this holder reuses the original screws to attach to the machine. However, you will need four additional M3 x 14mm screws to secure the sensor to the holder, as shown in the pictures. You will…
I wanted to relocate the cooling fan and wanted to cover the hot end and extruder. Print at 0.28 layer height. PLA works fine. no melting. Update: 19th Feb 25: I have now added a slimmer version, this is 32 gms, much lighter then 43 gms…
This is a mod that relocates the power supply of the Ender-3 Neo to the bottom of the printer and flipped the mainboard 180 degrees. The changes are meant for more room on the right side of the printer for a Dual-Z setup and easier…
Actually just did some minor changes from the original model. Add 4 lane filament hub and enlarge the screw holes to M3 This is a untested model ! So feel free to command. I'll try to correct asap. Update: It fits smoothly.
This is a very simple bracket that you slide into the top of the gantry to add the extra mounting hole required for mounting the display. You also need an extra V-slot nut, but there should be one in the spare parts of the Ender 3 kit.…
I don't like the stock location of the runout sensor on an Ender 3 S1 printer so I created a bracket that moves it down onto the print head. The bracket utilizes two existing fastener locations and is easy to install. It's stout enough…
This bracket is similar to already commercial available metal brackets on the market, with an addition of a extra hole for using zip-ties to secure the PTU-cable. with this you can move the PTU from the scorching engine-bay to the front…
This fits my MLOK cage I designed for my radio. It will relocate a BNC coax connection and audio speaker cable. Links Audio Jacks - https://www.amazon.com/dp/B0C9MDDLNG?ref=fed_asin_title BNC Jacks -…
This fits my MLOK cage I designed for my radio. It will relocate a BNC coax connection. Links BNC Jacks - https://www.amazon.com/dp/B08139D4XS?ref=fed_asin_title Related Models Icom IC-2350H Cage -…
This fits my MLOK cage I designed for my radio. It will relocate a pair of Anderson Powerpole connectors. Related Models Icom IC-2350H Cage - https://www.printables.com/model/1246431-icom-ic-2350h-cage MLok Relocation Bracket BNC -…
This fits my MLOK cage I designed for my radio. It will relocate a SO-239 coax connection. Links Related Models Icom IC-2350H Cage - https://www.printables.com/model/1246431-icom-ic-2350h-cage Relocation Bracket BNC + Audio -…
I added a larger motor for my y axis on my Ender 3 Pro, but it was so large that the bed contacted the motor before it hit the endstop. Made a quick endstop relocation mod to trigger the endstop before the carriage hit the motor.…
reuse the rear spool holder for the CFS filament buffer
This fits my MLOK cage and MLok rails I designed for my radios. It will relocate a digirig via mlok nuts. Links MLok Nuts - https://www.amazon.com/dp/B0B845WY3D?ref=fed_asin_title&th=1 Related Models Icom IC-2350H Cage -…
I converted my Harley Sportster XL1200C to dual gauges, and realized that the Custom line of Sportsters use different indicator lights than other sportsters, so I designed this bracket to relocate them below the handlebar clamp. Works…
Combined different models to accommodate the Y-switch on the chain holder
support is my design mixed with https://www.printables.com/model/559328-spool-holder-remix/files from @Nally3d and a remix with filament sensor relocator…
I really liked the unibody style of riser and so I printed AP's remix of a K1 riser, but I found the distance between the corners was a bit too big resulting in the legs not fitting into the four corners of the printer. This has a…
Remix to allow PUG instead of PG7 PUG hardware I used BOM x4 M3x5x4 Brass heated inserts x2 M3x8 Screws x4 M3x16 Screws
This fits my MLOK cage I designed for my radio. It will relocate a USB-B connection. Links USB-B Cable - https://www.amazon.com/dp/B002M8VBIS?ref=fed_asin_title&th=1 BNC Jacks - https://www.amazon.com/dp/B08139D4XS?ref=fed_asin_title…
For Ender 3 V3 KE printer. Fits a 4mm PTFE tube. You will need M3 x 12 screws to mount, no heat inserts needed.
Remix of horizontal z chain moving the mount to B drive to avoid collision of chain with blobifier Only compatible with IGUS chains Temperature mount can be found :…
A bracket for relocating the stock Ender-3 spool holder to the top rear. The spool does not interfere with prints. Now modified for V2 - Strengthened Hardware needed: 3x M4x10mm machine screws 2x M4x8mm (or longer) machine screws 3x M4…
This is a practical remix of the original tube relocation system for the Anycubic Kobra 3. It improves the installation process by allowing the mouth to clip directly onto the upper rod of the printer—no need to open the frame or unscrew…
Few adjustments to already existing PSU relocation model. Requires 2 m3 inserts.
NO MORE kinked tubes, broken filament or issues loading or unloading. This is a NEW version of my other riser that now has an incorporated slot to relocate the PTFE tube through the riser! Also has a larger relief on the back corner to…
If you are implementing a toolchanger using the stock SV08 toolhead, the rear located fan would need removing since it gets in the way when docking/undocking the head. This cowl allows the rear fan to retained by rotating it out of the…
MMU remix of the original, you can split the part in your slicer.
Relocating the filament runout sensor on the Creality Ender 3 V3 SE or KE can be a useful modification if you want to im
This is a remix of MandicReally's "Voron Y Endstop Relocation w/ PG7 Cable Gland Mount". The purpose of this remix is to allow it to be used with the Linneo cable harness, which uses a square flange mount with 4x M2x10 FHCS screws (with…
A simple mount for relocation of the runout sensor on an Elegoo Centauri Carbon printer. The example in the photo is PETG. I recommend Elegoo Rapid PETG , particularly when printing functional printer parts on the Centauri Carbon. PETG…
I was trying to install the 370 motor with low gearing to my C24. It turned out the upper part of the motor is colliding with the standard position of the truck bed. This model is my attempt to move the motor down. Additionally it…
This model was created to relocate the spool to the side, using Bowden tubes is recommended. However, it can be used without. This design is based on the Ender 3 KE, i would assume it should be fine for other printers as its only the…
A remix of @MP_660455 of the filament sensor relocation piece to give me more space to slide my carbon cartridge.
I like the simplicity of this model and the reviews of the fitment were correct. This model fits into the top of the Elegoo Centauri Carbon with almost a snap fit. I removed the rear rim so the top plate can be slid backward for venting.…
MadMax Dock Front Extrusion Relocation Bracket – 20mm Forward / 44.5mm Down For Mercury One / Ender 5 Frames This relocation bracket repositions the MadMax dock on Mercury One.1 or Ender 5 frames. It mounts horizontally to the front 2020…
I can’t really come up with a good scenario for why you would want to swap sides with the stock Ender 3 extruder (weight balance maybe?) but if you have the dual-z upgrade installed, this will let you do it. this was designed for my own…
I received the updated spools for the AD5x and they work fantastic except that they raise the center of the spool upwards so some of my cardboard spools would rub the IFS with channel 1 and 4 spools. I made this adapter bracket to lift…
Like so many others, I picked up the CFS upgrade kit for my K1 Max. However, having the long USB dongle hanging out of the front of the printer wasn't my favorite look. This lets you relocate the existing port to the rear of the printer…
2gauge battery cable hold downs for M6 bolts (Printed with PETG on its side) 2 gauge firewall penetration protection for a 22mm hole (you will need 2x M3 hex nuts and 2x M3x8mm button head screws (must be button head, or you will need to…
Clip for relocating a rear reflector to fit under saddle. Frees up the seat tube for bags and whatever.
This is a mounting bracket I created to relocate the extruder on the Ender 6 from the side to the top. I used two M3 T slot nuts to move the wiring harness more to the right. Then I used two M4 nuts, four M4x20 screws and two M4 T slot…
I needed a better solution for the dust colleciton on my Makita miter saw. First and foremost I wanted to move the connection point from the top, sliding portion of the saw down to the bottom and I also needed the ability to connect a…
Added support to bracket to allow better mounting and reduce any bending in design
