139 modeli
2mm thickness 330g with 0.2mm layer and tree support narrower≈290g for narrower one, I strongly recommend to use support enforcer as shown in picture I uploaded
A design for mounting a Beacon3D H Normal probe onto the tool-head of the Qidi Plus4 Update: 10th April 2025 I have uploaded an M3 screw variant of the mount for later model versions of the Plus 3 that use M3 bolts instead of 2.5mm…
V1.1: much smaller back panel cleaner model PRINT WITH ARACHNE (Orca Slicer: Quality → Wall generator → Arachne). Otherwise the thin support connectors may not print at all. ----------------------------------------------- This is a…
This is a newer ‘drop that can snap onto the input port of the printhead, and has a bevel on the input side of the elbow to ease install of the PTFE tubing. Note it’s intended to be a firm grip on the process so the tube doesn't easily…
I designed this spool holder for QIDI printers because the original one, when used with cardboard spools, often created too much friction. This could lead to false filament tangle detections and also generate annoying noise. After…
This is the third, and hopefully final revision of a set of vented lid riser pieces for the Qidi Plus 4. This model reduces the weight of my earlier models, and tightens up some of the larger dimensions for a better overall fit. Depending…
Summary The Plus4 can sometimes suffer from Heat Creep in certain conditions. This duct/plenum attempts to better route the air from the intake fan over the heatsink to minimise the risk of heat creep for parts with many fine retractions,…
In order to print PLA, you need to vent the chamber. I designed a quick and simple lid prop. I would print this and in at least PETG, likely higher temp filament like ASA or ABS. No supports, no hassle, quick print.
Adjusted Bambu Poop Chute for QIDI plus4 & https://www.printables.com/@spi0003_2484647
Strong, super-light, minimalist rear tool-head cover for the Qidi Plus 4 Important: Read the Caveats section below even if you read nothing else! Updates 3rd April 2025: I've uploaded a slightly wider model. There was a chance in a very…
This is a Fully enclosed 1in riser for the Qidi plus4 printer, Consisting of 6 separate pieces. This has slots done over the grab handles and along the back for material reduction (this is a hefty print as it is) but can be used to put…
A simple rear cover panel for upgrading to a 120mm fan instead of the tiny 4010 fan that cools the motherboard. This lowers the temperature of the board and drivers dramatically. I specifically used this fan - https://amzn.to/40oXwB6 but…
Please only print if you are OK with testing. Coming from the DIY printer world, I am not a big fan of the automatic belt tensioners on the Plus4. I desire too much control. So, I made new mounts and an insert to replace them with…
Please only print if you are OK with testing. If you're familiar with my previous replacement for the stock Qidi Plus4 auto belt tensioners here , these are an attempt at an improvment on those. This design utilizes the stock spring…
This part for the Qidi Plus 4 raises the height of your filament spool with 75mm for extra clearance of riser units like my own design or to use larger spools without a vented riser. It is recommended to use more walls and higher…
Update 11/10/2024: Uploaded modified parts 1 - 4 You can find them as parts 1 - 4 V2 Resized them in the middle section, where the PTFE tubing was rubbing against it. With these new parts there's no need to print out plug #3, but you need…
This build plate holder is designed to hold 4 pcs of 310mm build plates. Dimensions: Overall Length: 330mm Main body width: 40mm Overall width: 120mm Overall height: 60mm Print settings (I used PETG, but feel free to print with any…
Was inspired by the remixed design, but made a few significant changes such as: - Removeable poop tray, with angle of slide adjusted to suit - I found the slide was a little too short for my setup, or it could of just been my mods, so it…
The stepper motor drivers on my Qidi X-Plus 4 were reaching temperatures of up to 100°C. I mounted a 40mm x 40mm radial fan with a 3D printed mount. This reduced the temperatures by around 30-40°C. You will need a 40mm x 40mm radial fan…
Another poop slide for the Qidi Plus 4. This one can be printed in one part as it comes ready with break away supports. It features detachable trash cans in two sizes. The trash cans are held in place by 5 small magnets on each side (10…
Spool holder for Qidi Plus4 with bearings so that your spool will turn smoothly. Materiel needed : 2 x 6804 bearing.
I created this model to quickly replace the broken part in feeder and continue printing. it works wery well, but step file is also attached. UPD Jun/20/2025: replaced with v11, more sturdy now
Simple build plate holder for 5x 310x310 plates. Printed mine in ABS but should be fine with any material. Hope someone finds it useful.
This remix adds 3mm of spacers for the ring and screw holes to slightly reduce fan noise.
Download TPU printed parts and PETG printed parts from here https://makerworld.com/en/models/417509#profileId-319901 Use the center core for K1 or Voron
Toolhead filament sensor to replace the Qidi hall filament width sensor. Useful for filament changer systems. Uses the wiring and connector of the original filament width sensor. Uses the 6mm collet from the original filament width…
Qidi Cover – Remix with Hex Pattern & Logo This version of the cover is compatible with Stew675’s project , which allows you to mount a Beacon / Cartographer 3D probe . This model is a remix of the original cover created by @Derek_2843290…
Replaces front panel of stock camera mount to add ventilation and adds easy to grip hood to lens for focus adjustment. Existing camera will need glue removed from its lens barrel to permit focusing. Installation is under ten minute…
The rear vent shield is contained in two versions altered for 24V-80mm-fans for enhanced airflow: A lasercut model from acryl and a printable model with reinforced structure. Both can be fitted with 80mm fans to replace the original, tiny…
Eine verbesserte Lösung zur Kühlung der Hauptplatine des Druckers, bestehend aus einem Hauptteil und einem Deckel für die Filterseite. Für den Lüfter habe ich mich für dieses Modell entschieden: https://www.amazon.de/dp/B086SKG982 ?. Der…
Hab mal einen Halter erstellt damit man den Sunlu S2 an der Seite der Qidi Plus4 aufhängen kann. Einfach die 2 Schrauben vom Handgriff abschrauben, den Halter einstecken und die Schrauben wider reinschrauben. Der Haltegriff kann im Gerät…
Compatibility: A very rigid mount for your eddy current probe. Compatible with - Beacon3D revD, revH - Cartographer3D (the one that has the same shape as beacon revD) NOT compatible with: - BTT Eddy The model allows you to swing the probe…
Dieser Filamentabfallbehälter für die linke Seite des Druckers besteht aus zwei Komponenten: einer Rutsche und einem Sammelbehälter. Die Rutsche besteht aus dem Hauptkörper und einem Deckel, die nach dem Druck einfach zusammengesteckt und…
More info on the PCB can be found here: https://ftdichip.com/products/usb-com232-plus4/ The board is based on an FTDI chip. It is capable of converting 4 RS232 ports to USB. It has 4 DB9 (D-sub) connectors for the serial ports and a mini…
Diese Erweiterung für den Glasdeckel des Druckers besteht aus sechs Segmenten, die nach dem Drucken einfach ineinander gesteckt werden können. In den Mittelteilen sind zwei Gehäuse für Sepa-Filter mit den Maßen 81 x 42 x 15 mm integriert,…
(Excuse my print quality on my sample image, I was experimenting with a new filament.) This is a monitor housing for the Qidi Plus 4 that replaces the original housing. it does a few things: Adds a hinge so that you can adjust the angle…
Easy way to hang your top cover on the left or right side.
This design utilizes the stock spring itself but allows the user to adjust the tension with a screw. I have remolded the original model so that there is more material near the top and have added the correct hole size and depth for the M5…
An easy to print, replacement for the Qidi Plus 4 end-stop cutter activation block. Print with a 0.2mm layer height in any material capable of withstanding at least 85C temperatures without going soft Reduces the end-stop exclusion zone…
Models of the OEM spool holder and chassis mount for the QIDI Plus4. These are modified versions of the models from QIDI, but slightly more appropriate for 3D printing (vs. injection molding). I haven't printed these yet, and they have a…
Stand for the NanoVNA V2 Plus4 With integrated holder for the stylus and the three calibration plugs (open, short, load). In addition, the female/female SMA adapter can be accommodated here. Ständer für den NanoVNA V2 Plus4 mit…
This is my attempt at making a replacement for the internal chamber circulation fan filter box on the Plus 4 that can accept HEPA filters. I used the same filters as the person who previously designed one, but I designed it a little…
I made a small cover for the right side panel bolt. The bed cable has a tendency to get snagged behind it and this cover prevents that. I made a project file for the QidiPlus4 with height modifiers so the final surface finish is…
Beacon Simmetric Holder Reworked for QIDI Plus4
Please use STEW675 holder https://www.printables.com/model/1253290-modified-for-attach-the-head-front-cover-with-the
I printed Stew's version and noticed the holes didn't quite line up to the stock Plus4 purge bucket assembly. The printed part was also quite wobbly and had very loose clearances with a well tuned machine. I noticed a lot of the printed…
My take on a Plus4 tool head beacon mount and cooling mods. A few of the advantages compared to the stock, and other users mods are: Visibility! The nozzle is easy to see from the front of the printer making print progress and nozzle…
I was having trouble obtaining a M8 100mm bolt for a reasonable price so I remixed it to use Imperial hardware. Print the aufnahme and mutter STL files from the original. For the spool holder, the following hardware is required 5/16" -…
A silicone rubber gasket with outer diameter of 100 mm and diameter of 3.5mm is required. This adapter can be connected to a duct with a diameter of 100 mm . Depending on the hardness of the silicone O-ring you use, you may need to cut…
Qidi Plus4 Cover Mainboard Abdeckung for Bigger Mainboard Fan Better Cooling and easy swap Cooler Amazon :…
Update: This design is now on version 3, which is even less tall that some of the previous makes. It is reliably working on my machine. After printing and installing the modified filament cutter block, I noticed that there was still a lot…
I thought it would be nice to replace the ugly useless handles with simple covers. Remove the screws and handles, and set aside. The covers lift out easily. I printed on my QIDI Plus4 in "burnt titanium" multicolor ABS in “Strength”…
The USB port seems rather overexposed and this seems like an obvious upgrade. Should reduce anxiety and keep the USB port and flash drive protected when replacing the cover. Uses the original flush head case screws. To make it easier to…
Want to use a lid riser, or just move the spool? Qidi Box in the way....move your spool! Easy print, use your current plus4 spool holder spindle. CAD -…
UPDATE: RC2: Smaller diameter cylinder so it actually fits through the hole… Smaller length cylinder so you can install it without tension applied to the belts. I only had 30mm long screws at home so I started to design a variant that…
A quick, complete redesign of a sealed waste / poop box for Qidi Plus4. This box is a bit larger than other similar slot-on models, sits further off the printer (helps with mainboard airflow), and is mostly air-sealed which helps keep the…
I had heard that the Xmax3 are the same size as the Plus4 and are swappable (with some changes to the plug) (reports are the q1pro hotends are the same length as the plus4) Later on I heard that it is 4mm short. So I Stewy helped me with…
I use the tool holder in the hot chamber of QIDI Plus 4 with a specially designed 1x7-sized Gridfinity-compatible base plate as shown in the photo. It fits perfectly in the dead space in the chamber. It provides the tools exactly where I…
I found a hole on the metal frame of my QIDI Plus4 and made use of it to hold this Allen key holder. The holder firmly snaps onto the frame without glue or screws. The Allen keys are dedicated to use in the hot chamber. So I'm happy to…
This is a Qidi Plus4 rear vent cover which accepts bigger fans (80mm/92mm) and allows attachment of big poop/purge bin - https://www.printables.com/model/1055602-qidi-plus-4-purge-trash-bin
You can store nine Plus4 nozzles in this small Gridfinity-compatible (1x1x8) case with a lid. If you combine it with the specially designed intra-chamber Gridfinity base plate for QIDI Plus4, it stores the nozzles in the dead space of…
I have some older PLA spools that are too wide to be held by the original filament holder on the QIDI Plus4. This inserts in place of the cap, with three extension positions. The original cap goes into the end. Print Settings Printer:…
Heatsink Fan Mount Ducted Square modified slightly to fit The Conch Qidi Plus4 hotend with Stew675's carrier plate.
Replacement for the QIDI Plus4 handle used to lift up the printer. I measured the original one and modeled it in FreeCAD. Now you can make handles in any color you'd like! *Printing I highly recommend printing this laying down to avoid…
Eine verbesserte Lösung zur Kühlung der Hauptplatine des Druckers. Für den Lüfter habe ich mich für dieses Modell entschieden: https://www.amazon.de/dp/B086SKG982? (GDSTIME DC 24V Lüfter, 80 x 25mm). Der ausgewählte Lüfter ist bürstenlos,…
This alternative shroud requires 4x m3x12 screws, 4x m3(x2.3mm) nuts and 2x 5x2mm neodymium magnets. Printed in TECBEARS PETG it weighs 32g vs original 40g shroud but will vary depending on filament. See images for print orientation and…
I made this because the carbon pellets in the stock machine is too small for high VOC printing like with ABS, this recirculating vent holds a LOT of carbon pellets and a hepa filter as well as 4020 blower fans if you want. like the…
Want to keep your toolhead cooler than the chamber? use peltier cooling! now with 95% enclosed toolhead! Why are you here? why are you doing this? do you know what you're doing? what if your machine breaks? what if you start a fire? are…
Made this for my QBox at tangle sensor. Suggest printing: Mat: ABS - PA612-CF or equivalent (NO PLA) Layers: 0.08 ~ 0.12 max full walls and 100% infill or you can try 1 wall-100%infill with ALL SOLID SURFACE ironing SEE VIDEO…
I received a request to create a replacement cap for the QIDI Plus4 printer filament holder. This seems to work. I'm using it now to print a second one. I'm printing in generic ABS with a 15% grid in infill. I added a 5mm inside & outside…
General: This upgrade is for the Qidi Plus4. It helps keep the stepper drivers and motherboard cool when operating the chamber heater. Why I designed this: I was printing some PC-PBT for the first time, and the printer kept shutting down…
Place the backside edge of QIDI Plus4 lid on this lid riser, to rise the lid to have better air circulation when printing PLA. The lid can be closed without removing them. So, you can keep them always attached to your QIDI Plus4. They are…
This model of the cooling fan moves the fan output nozzle over so that it does not touch the E3D revo High Temp hotend running on a Qidi plus4 Use at your own risk
This is a spool holder for QIDI Plus4 that you can hang on the side, utilizing the bolts that hold the left lifting handle. As such, it's probably INCOMPATIBLE with many of the available risers You can use it with the stock filament hook…
Need somewhere to put the QidiBox but print a lot of PLA? Like to have more gentle filament feed path tube bends? I made it with a slight angle so I do not pile things on top of my printers, to try and keep things clean :) The walls are…
Better Tab to hold the top glass Glass is heavy, use ASA or PETG to avoid heat creep issues. I also suggest gluing them in place Mirror model for other side.
Wanted a second relay to use with an AC heated bed conversion I was doing to the Qidi Plus4 Consult an electrician for wiring if you're not sure how to do it. Stock chamber heater to relay conversion: Red wires on the stock relay are Live…
Wago 221 (2 connnector) mount for Qidi Plus4 inner wall standoff
Qidi Plus4 Broken Heater Chamber Mount Fix - Nut & Bolt substitute. I made this part instead of using the recommended nut-and-bolt solution proposed by Qidi support when my heater chamber fan snapped off. Made this fix to integrate a…
This is an extended filter basket. The HEPA can sit on top of the filter and then the carbon material can go below it. The HEPA filter is the same as others https://www.amazon.com/gp/product/B0782T7L6P (HEPA Filters Replacement for ILIFE…
Guarding touchscreen from toddlers that like to push buttons on screen :) Slides from top to bottom and vice versa. Use both hands to do it straight. Print verticaly. I've used 0.6w walls and 0.2 layer height.
Eine Ersatzkappe für den originalen Filamenthalter des Qidi Plus4. Sie besteht aus zwei Teilen, die nach dem Druck einfach ineinander gesteckt werden. Die Verbindung hält sehr gut ohne Klebstoff, kann aber bei Bedarf mit Kleber fixiert…
I upgraded my top lid raiser after installing the Qidi-Box on top of the lid. The filament changer adds a lot of weight on the top lid, for PLA the hot air has to leave the print enclosure, therefore the raiser. I designed it much bulkier…
Ein Filtersystem, das neben Aktivkohle auch einen Feinfilter enthält, könnte beim Drucken mit ABS von Vorteil sein. Die Aktivkohlepellets werden in das Innere des Filtergehäuses eingefüllt, bis es zu etwa drei Vierteln gefüllt ist. Bevor…
Placing the 1 kg spool lower down reduces the impact of having such a heavy item so far from the printer's centre of gravity. As a bonus, it allows one to see at a glance how much filament is left on the spool, instead of having to crane…
I thought it would be nice to replace the ugly useless handles with simple covers. Remove the screws and handles, and set aside. The covers gently pry out with a small slotted screwdriver if needed. Or, tap a screw hole in the middle and…
All prints are with no supports easy prints. draw fit is snug and stay in place when pulled out. prints are all done in pla+ 0.28 25% infill 230c hotend 60c bed.
A remix of the awesome lid. I printed it in black ASA GF filament.
Переработка охлаждения холодной зоны для QIDI Plus4 с установленным хотендом Phaetus Conch. Проект создавался не как декоративный мод, а как решение конкретной технической проблемы штатной головы QIDI Plus4. Стоковая система охлаждения…
Follow the same instructions as the model the is remixed off of, and use the new double walled back plate that is posted here https://www.printables.com/model/1237621-draft-beta-double-walled-backplate-for-insulating
I created the adapter standoff for @Sarge013 low profile heatsink SSR mount (FIRST VERSION) . NOTE: There may be a new version available from @Sarge013 now. I had to make these as I was in a slight bind because I had already removed my…
@MW_3106447 designed a nice mount for the Beacon3d Eddy Current sensor that mounts the sensor behind the head in place of the layer cooling fan. The layer cooling fan is then moved to the front of the toolhead, but the original cover no…
This is a remix to allow the Qidi Plus4 box hub bracket to attach at the same time as the spool holder. As you can see from the images, it does not block access to the screws for removing the back panel. This spool holder can use either…
This mods the stock fan so that there is a place to mount the Beacon RevH. There is also a hole for the cord to go. Use normal Beacon RevH's not the low profile versions First version mounts on the front, the hole is for the cord to go…
我使用了耐高温的双面胶带进行粘合。根据卖家的描述，这种胶带是为连接 LED 灯条而设计的，可长期耐受高达 120 摄氏度的温度和高达 180 摄氏度的短期耐受性。您可以通过在购物网站上搜索“LED 耐高温双面胶带”来找到它。它只能与“Qidi Plus4 超轻后置工具头套”配合使用。
I needed a third hand to hold the tangle sensor tube while I depressed the PTFE holder with one hand and inserted the tube securely with the other. Printed in PETG for flexible strength. Used the Plus4 Strength profile. Added a 8mm brim…
Toolhead cover for Qidi Plus4 when using Beacon3D mod by stew675. Had to save it as .3mf so the colors can be changed to match your filament for beacon logo. I used blue instead of green for the Beacon logo since I didn't have any green…
Qidi Plus4 10mm x 3mm Belt Tensioner Shim There have been report(s) of reducing some VFA using either belt tensioners like one by @Jerky_FPV_1021902 or adding spacers (3 stacked M5 washers) in the stock preloaded tensioners and rewracking…
This is an articulated double hinged door frame seal that I designed some time ago and have only gotten around to testing, it's been up on printables for a while but I minimized tagging it or sharing it to get it to a better releasable…
The changed fan grille allows for more airflow to be brought in by the fan. I printed mine in ABS and had just a tiny bit of shrinkage.
