Liczymy pasujące modele…
Heyho You can install the part to get more comfort or to attach it in places that were previously not possible. In addition you can use cable ties to give the part additional support. Scaling Scaling is a very important factor with this…
Goal: a new high current loop key design that is: easily 3D printable captured / self-contained / no losing keys or carrying another fob compact & small footprint secure mounting locks out when powered down slick looking reliable Specs:…
for this little guy self explanatory due to positionion supports are suggested unfortunately comments or suggestions on a prettier version are welcomed!
A clamp to stop the ptfe from movement during retraction due to the ptfe fitting lock moving in and out of fitting. there have been 3 edits since initial release, lengthened the lock collor relief, increased its outer diameter clearance,…
The Tascame Portacapture X8 isn't shiped with any form of casing in the box and I wanted one which can hold all the naseserry equipment for it. So I put an inlay in one of Whity's Rugged Boxes for the Portacapture X8 itself along with…
A clamp to stop the ptfe from movement during retraction due to the ptfe fitting lock moving in and out of fitting. there have been 3 edits since initial release, lengthened the lock collor relief, increased its outer diameter clearance,…
Plug a drybox closed and capture/retain filament in it so that you don't have to open the dryboxes to fetch filament . It clips to a PTFE tube when not in use. This .3mf now prints well on my printer and this particular PETG filament, but…
There are one or two 3D printable shelves on the internet designed to hold a Sony A6100 Camera but none are designed to accept the camera without first removing the Peak Design Capture plate. The shelf holds the camera ~18mm Away from the…
Remix of https://www.thingiverse.com/thing:6401198 The beauty of this mount (as well as the original design) is that it mounts to the bed, keeping the print itself in a static frame of reference so you can actually get stable timelapse…
Use 2x M3 bolts to capture charger with 5mm thick tab. I created this around the battery for the bissell prolite stick vacuum with the detachable battery. Not sure what other vacuums this works with.
Paper capture bar for the RICOH SP C261SFNw printer in 2 versions, split and whole, use it to your health!
There is the STL to Print and also the Fusion File to change some parameters like the Screwholes I glued the mount with double sided tape and will screw it later on my desk. Printed in PETG with no Supports and to assemble it just flex it…
COLLARUM® Live Capture canine device safety plug secures the bait block trigger so it can not release.
What is this? A modular rigid body system for optical motion capture, designed by a researcher who actually uses these in real experiments. Instead of buying overpriced proprietary rigid bodies, print your own with unique marker…
I received a lovely Peak Designs Capture camera clip for Christmas, but the tripod plate that came with it was too bulky for my small camera (a Panasonic GM5). I know an Arca style tripod plate can be made small, because I have one that…
In astronomical imaging it is important to capture dark frames and bias frames. This filter allows you to obtain such frames.
Heyho You can install the part to get more comfort or to attach it in places that were previously not possible. In addition you can use cable ties to give the part additional support. Scaling Scaling is a very important factor with this…
I don't like carrying binoculars dangling around my neck and find bino harnesses too much a hassle. This 2-parts adapter allows to fit a capture clip mount to a pair of binos (mine are Kite Lynx HD+ 8×30), in order to secure them to a…
I'd recommend checking to make sure that the USB connector is fitting flush, my card had cold solder joints and was becoming bent.
Hello Friends! Here is a system to replace the classical adapter of the Mannfrotto light 290 Tripod original one in order to be able to directly snap on you camera with a Capture Plate (from Peak Design) mounted on. Here is a video on how…
See GitHub for details of the project. This version of the case is for a Raspberry Pi -5 and SSD with the Tijl KNX hat (Pictured below). If you are using the Weinzierl KNX Hat, you will need to print this case . You will also need a 30mm…
See GitHub for details of the project. This version of the case is for a Raspberry Pi -5 and SSD with the Weinzierl KNX Hat (Pictured below). If you are using the Tijl KNX Hat, you need to print this case . You will also need a 30mm fan…
Sculpture of a Lightning Rod with a Catcher Point or Franklin Point
Needed two knobs for M8 all-thread for a table saw joining and tapering sled. This design uses a captured M8 nut. Insert before covering layer, I use M600 for pausing (edit gcode). I've since used this design in other projects and it's…
This model seals the picture in the frame. The picture is captured and can't be removed without destroying the frame. You have heard of capturing magnets or bolts in a plastic model; this model captures the picture. The result is very…
A simple box with a sliding door designed to fit an HD60S+ capture card. It features side holes for cable management, with internal space to store cables when not in use. The top includes a tray to hold a Nintendo Switch dock.
The Tascame Portacapture X8 isn't shiped with any form of casing in the box and I wanted one which can hold all the naseserry equipment for it. So I put an inlay in one of Whity's Rugged Boxes for the Portacapture X8 itself along with…
The GPIO Hackerboard is a great addition but it doesn't come with any good options for placement or retention. Enter a low-profile, fast-printing holder that sticks anywhere a magnet will. The cutout on the bottom should prevent…
I, originally, printed the XL Camera Mount | Buddy3D for the XL Enclosure and noticed I could not capture the entire print bed as the head of the Buddy3D camera could not tilt any higher. I duplicated the mounting base and rotated it to…
While outside the bolt attaching the pin to the mounting clip flew off and I lost it. Here is a replacement pin for the mounting plate since Peak Design does not offer any spare part for it. Only down part is that the locking mechanism…
Update 15.03.2025: Added a simple cap for the screw holes on request by @Codejoy_48654 In order to free up some room, i decided that i wanted to store my cameras on a wall mount, thus designing this simple Arca Swiss style one. V2 and V2…
I always leave the Peak Design Capture Clip plates on my cameras, but also wanted to use this fantastic gridfinity bin for the Sony a6700! I've added two different versions - one should fit the smaller Peak Design Capture Clip plates,…
Adapter for mounting flashlight to your Peak Design Capture. Made for my Fenix HM61R Amber V2.0 but you will probably find more uses. I printed mine from PC with carbon fiber, but any material should do. Print without changing…
Let your Valentine know that your heart is theirs by making them a You've Captured My Heart 3D print! You can set your captured heart on any flat surface or hang it using the ring at the top of the cage. PLA version: PETG version: The…
I wanted a battery holder that I could place in a storage box and not worry that the batteries would fall out if the storage box tipped. I designed this simple holder with spring loaded sides holding each battery.
Ok let's be honest, when it comes to fastening bodywork and other bits, Aprilia makes some pretty dumb choices. For example - if you try to remove the mirrors for a trackday or whatever, you will discover that the nuts drop down behind…
Discussion This assembly replaces the outer HEPA filter housing on the Prusa XL Enclosure adding: Quick Access to HEPA Filter for Maintenance purposes Removable connection to 2.5" exhaust duct Both parts are magnetically connected to the…
A simple adapter to use the Peak design capture plate with a T-Echo. mounts to the back of the Echo with 2 M3 6mm screws. Button top or pan head screws work well, socket head screws may interfere with mounting plate.
If this looks similar to the one I did for the EVGA XR1 Lite…well, I made them both at the same time while I had my nose in Tinkercad! The premise is the same: Get this poor capture card off my floor and mounted up to my wire shelf that…
A friend of mine gave me a box of stuff and this thing was in there, so I made a mount for it. A couple differences in the picture and the final upload here. In the back, it was not sitting flush against the back wall for one. I…
The action grip is centered on the lowest camera sensor, for a good balance of parallax-on-rotation reduction and centre of mass fatigue reduction. Single print, no supports required, optional M2 screw attach points for extreme levels of…
I don't play chess as well as I want to. This is a little desk top reminder to look for checks, captures or attacks on each and every move. If printing in two colors, I had the color change at layer 22.
Effortlessly harvest rainwater that clings to your downpipe walls! This insert fits snugly between standard 75mm rainwater pipes (5mm wall), redirecting water through a 12mm hose connection to your barrel or tank. Excess water flows…
This is a compact tripod mount designed to hold both your 360 camera (tested with the Insta360 One Inch) and an ambisonic sound recorder, while minimizing visibility in the stitch line. The mount is compatible with the Ulanzi Claw…
This is the 3d-printed case for the GB Interceptor. An open source rp2040-based adapter that goes between your (unmodified) Game Boy and the game cartridge to record or stream your gameplay via USB. To learn what it does and how it works,…
I was looking for something to make pictures about products mostly for selling on the net and 3d modelling. There are a lot of good motorized turntables on the market and I saw many good creations here too however I wanted some simple…
Having a Peak Design capture camera clip and an Velbon P-Max tripod, I had some issues when using the tripod. The size of the Velbon mount is 42mm and the one from Peak Design is 38mm. So you can't really fit the camera tight to the…
Introduction When you change something in your mechanical ventilation system, it’s a good idea to double-check that all vents still deliver enough airflow for a healthy indoor climate. Pro measuring tools are pricey, and the DIY versions…
when I bought this capture card I run into a problem with it's usb plug, the plug is very loose and will disconnect if I touch it. so I made a case that replace the original case that have a hole for a usb cable. soldering skill and hot…
Labs often capture honey bees and then need to introduce them to apparatus or transfer them. The plunger helps to gently introduce a bee into apparatus. This design is a simple modification to a snap cap vial. You will need to drill a…
This is a Case for Pi 4 and Pi 5 that supports the Geekworm video capture hat. The hat routes HDMI input through the CSI-2 port on the Raspberry pi so that it behaves more like a pi camera. It also has a low latency HDMI loop back to get…
This is a small cord capture for pendant lamps. It is designed to for the body to be mounted to a wall with a screw, the cord to be placed in the groove and a the cap screwed down snugly on top to secure the cord. No supports any infill
This is a community project and was designed by me with a lot of feedback from the community. Thanks to all the testers, helpers, and everyone who printed the finished model. More about the Macher Festival: macherfestival.io
This holder attaches a bobbin to the corresponding thread spool so you can store them together in place. Based on the v5 from the original version. FreeCAD file included so you can adjust it, but warning, it's a laggy file.
Sculpture of Nicolas Maduro being transported to NYC, comes in two versions: split and full body. Split is better quality, but leaves a line that would need to be filled and sanded prior to painting.
This is a grip for an O3DS that's been hardmodded with a capture card. The grip has a big hole in it that the extra girth can slip right into, nice and snug.
Plug a drybox closed and capture/retain filament in it so that you don't have to open the dryboxes to fetch filament . It clips to a PTFE tube when not in use. This .3mf now prints well on my printer and this particular PETG filament, but…
A unique 3D printable creation — this Fidget Ring Spinner, Print in Place, Spinning Outer Band, Captured Bearings Tested on 8+ FDM printers. Download and print immediately. **What's Included:** - STL File - 3MF File - OBJ File - PLY File…
A unique 3D printable creation — this Fidget Ring Spinner, Print in Place, Spinning Outer Band, Captured Bearings Tested on 8+ FDM printers. Download and print immediately. **What's Included:** - STL File - 3MF File - OBJ File - PLY File…
A unique 3D printable creation — this Fidget Ring Spinner, Print in Place, Spinning Outer Band, Captured Bearings Tested on 8+ FDM printers. Download and print immediately. **What's Included:** - STL File - 3MF File - OBJ File - PLY File…
A unique 3D printable creation — this Fidget Ring Spinner, Print in Place, Spinning Outer Band, Captured Bearings Tested on 8+ FDM printers. Download and print immediately. **What's Included:** - STL File - 3MF File - OBJ File - PLY File…
There are one or two 3D printable shelves on the internet designed to hold a Sony A6100 Camera but none are designed to accept the camera without first removing the Peak Design Capture plate. The shelf holds the camera ~18mm Away from the…
Remix of https://www.thingiverse.com/thing:6401198 The beauty of this mount (as well as the original design) is that it mounts to the bed, keeping the print itself in a static frame of reference so you can actually get stable timelapse…
Use 2x M3 bolts to capture charger with 5mm thick tab. I created this around the battery for the bissell prolite stick vacuum with the detachable battery. Not sure what other vacuums this works with.
Paper capture bar for the RICOH SP C261SFNw printer in 2 versions, split and whole, use it to your health!
There is the STL to Print and also the Fusion File to change some parameters like the Screwholes I glued the mount with double sided tape and will screw it later on my desk. Printed in PETG with no Supports and to assemble it just flex it…
Printable version of the divider cards that come with the Ugmonk Analog Capture kits (small and large sizes)
COLLARUM® Live Capture canine device safety plug secures the bait block trigger so it can not release.
What is this? A modular rigid body system for optical motion capture, designed by a researcher who actually uses these in real experiments. Instead of buying overpriced proprietary rigid bodies, print your own with unique marker…
This is a 2 part print in place nut that is captured on the bolt between two fixed ends and is basically the same print as the impossible nut I posted but I added a top and bottom to the bolt to make it easier to hold. I included both the…
COLLARUM Live Capture comes with 2 types of bait block. Both I find difficult to load with bait. Printed in PETG, 5 perimeters and 25% fill. The T bait block has an open trough to fill with bait. Share your make :)
See this video for documentation: All parts printed in black ASA (aside from LED diffuser). Scaled to be dimensionally accurate.
Overview I needed to mount a 10" rackmount system onto some wire shelving. This bracket helps with that. Assembly is pretty straight forward. Put the nut in the hole, and then thread the screw in to whatever you need. The zip ties should…
The funnel adapts to the shape of the nuc, making it easier to deposit the bees. The funnel does not obstruct the sliding bottom of the nuc. This model is dedicated to APIDEA mating nucs. L'entonnoir s'adapte à la forme de la ruchette, ce…
Imprimir en vertical y ajustar el tamaño para que entre bien la capturadora en el soporte.
Since the USB port on my capture card broke because it was hanging from my PC, I designed a magnetic mount to provide some strain relief for the connector. I used 4 round magnets 8mmx2mm. It should fit a lot of generic video capture cards…
This is a second concept for a stackable Direct Air CO2 Capture machine. The idea is that each module is sized to fit into an ISO container footprint which allows factory assembly before transport to site where they are simply stacked and…
Update 6/29/22: Added a version with a centered ¼-20" thread and no boss (i.e., MagSafe compatible). Use caution – this will be less secure than the SlimLink version. Update 4/27/22: Added a version with a centered ¼-20" thread A magnetic…
Designed this thing to stop the bolt heads from spinning on my Juntek VAT 1300 Power meter. The spinning makes it very hard to get the nuts done up tight, and can damage the circuit board. With this design, the bolt heads don't touch the…
Was just seeing if I could do it. Probably don't need a skirt, but I have adhesion anxiety. I used black duct tape on the back of the quarters (on like the 3rd attempt). Drop the quarters in place, tape side up, on layer 21-22. layer 23…
Infill=15% Quality=0.20 doesn't matter that's what I did though. Supports=I would use supports under the ball. Paint them on if you have prusa slicer.
Just tidying up some of my earlier uploads to something a little more presentable ; ) Cheers Jace
This is my first submission while I wait for my MK3S+ to arrive. Expect great things.
This model was ideated to be larger, but I settled on three knives because that's how many I usually take camping. The bar is supposed to be spring loaded. The bar prints in two parts and is keyed to a fulcrum in the block. The drawer is…
Introduction This is a mount designed to attach a Peak Design capture plate to an old style Hydroflask 32oz or 40oz wide mouth bottle. Compatibility This design is intended to be used with a lid that is only removed for refilling, not the…
Remixed to optimise for the capture clip, tighter tolerances, less overhangs, shaved off a part to allow more flexibility on the gopro Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill:…
I recommend full supports, but build plate only might work.
This is a simple hand-held mount that we designed in 2014 for a pair of Canon PowerShot A4000 cameras to capture synchronized stereo images or video. The camera mount is our own design, holding a pair of A4000 so that the stereo baseline…
A great design already but I just prefer to have the hex nuts embedded in the bracket. Makes install just a bit easier. Made for M3 bolts and nuts… 5.5mm across flats.
Note: Several of my designs (and remixes) for my CNC plasma rig are available here for free, and several others are exclusively for my supporters on Patreon that support for any amount, even if only a dollar a month.…
I received a lovely Peak Designs Capture camera clip for Christmas, but the tripod plate that came with it was too bulky for my small camera (a Panasonic GM5). I know an Arca style tripod plate can be made small, because I have one that…
Zack Freedman’s original Gridfinity Base Plates https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%2520Baseplates-60925 Also inspired by https://www.printables.com/model/250550-gridfinity-magnet-light-baseplate Optimal settings:…
"Capture the Flag" is a popular catch game that is usually played with several people outdoors or in sports halls. The "Capture the Flag Boardgame" is based on this team game and brings the fun of the game home. A fast and strategic board…
I was learning how to model custom nuts and bolts in Fusion 360 when I had the idea to create this fidget toy. The bot has a stopper at the end to keep the nut from spinning off. I printed the nut and bolt with PLA at 0.20 layer height…
UofH UH University of Houston logo with or without captured magnets. When slicing the captured magnet file be sure to set the color change just before the cavities are covered. It will be a snug fit with a 2mm magnet. Be sure to check the…
A quick remix of Schnipp's fantastic Two Way Bolt, with a lengthened shaft and a bolt head on each end to keep the nut in place. Make sure to check out the original! Printed the nut separately, then printed the bolt vertically using the…
