Liczymy pasujące modele…
This organizer shape was designed so the pouch would easily slide in each niche while spreading the contents inside evenly to save space. All the pouches can be seen and easily taken from any angle. Prints with no supports :) As usual,…
A work stand for working on 4-bbl carburetors with the narrower bolt pattern (4.25" x 5.625"). This fits a Carter Thermoquad (shown in pic) and I believe also the Rochester Quadrajet. This is based on the carburetor work stand print…
This is an experiment replacing a normal gasket with a TPU made gasket for a lawnmower carburetor. All credit goes to The_Eddies on youtube for this brilliant idea and design.
This is the carburetors required for the VW Engine model. These are EMPI two barrel carburetors. Two are required giving one barrel per cylinder. Refer to the assembly instruction for the parts required.
This model was designed to fit a 4160 750 cfm Holley carb with a choke horn. It should fit any 4150/ 4160 carb with no issues and may also fit others. I used a cheap carb stud from amazon cut down to hold it during storage. If printed…
This is a 90 bit holder for 1/4 hobby screwdriver bits designed to make it easier to adjust the mixture screw on my Honda Nighthawk Carburetors. The middle carbs are still a little difficult but much easier than using a regular…
This is a great tool but had to make a small change to fit my carburetor
My chainsaw's carburetor has a secondary air inlet with its own valve plate. The lever in this model actuates that valve plate. A projection on the throttle linkage pushes this lever to open the valve plate at high speed. While doing some…
I pulled the STL into onshape and tried my best to replicate it, but that isn't always easy. It fits exactly the same as the original, except with better clearance near the jets (see the photo of the original's clearance). V1.2 update:…
In this publishing I have included stls for 2 designs for the Carburetor adjustment tool. I used a Ryobi R09050 blower for testing and fabrication. I also included the blend file that I created the peices so you can modify in any way you…
I lost my original carburetor adjustment gauge. After seeing a tool I purchased for $4 dollars twenty years ago is now $20 I decided to print one. This isn't my idea or design but is the most popular type of tool on the market. It's…
stand for 6/8/10mm rod with 3 sizes of Retort Rings (40/50/65mm diameter) For each ring I made a version that also connects to the wall. Ingredients: 2 m3 screws + inserts nut to connect the rod to the stand m3 screws + inserts for each…
Boîte de rangement de gicleur de carburateur Dellorto. Dellorto Carburetor Jet Storage Box.
Cap for vacuum or carburator storage small-1/4 medium =5/16 large=3/8
I printed it with PETG 0.6mm nozzle 0.2mm layer height 3 perimeter After I clamped in place I used a zip tie to secure it. About FreeCAD . About FreeCAD Realthunder fork .
This model is a 1-1/8 in. riser for use under the base of a Holley 4500 Series Dominator Carb. Designed for use with the 1050cfm model. I printed the file with Nylon-CF with 25 percent gyroid infill 0.2mm layer lines and 4 walls. To…
Noticed the similarity in size between a v6 nozzle and vm18 jet so I whipped up this little remix of Reven's nozzle box, this uses the .2mm tolerance version as a base. First print with the original hinges broke coming off the bed so I…
A filter (around 2mm grid size) that inserts into a 2" velocity stack, as used on e.g. Weber carburetors Category: Automotive
This add-on is a high-quality piece with highly realistic details. Congratulations to the creator of the original piece. Look the Assembly.pdf for details.
This is a small 3D scanned Pretorian Helmet by the Artec team, done with an Artec Spider 3D scanner (Small 3 by 2 cm roman helmet captured with Artec Spider 3d scanner). I scaled the model up, oriented it and smoothed the mesh in some…
very accurate model of the 22 mm carb for 212 cc engines
This is a dragster style carburetor scoop I designed for my boat. It requires quite a bit of post-processing to make it look finished. The Mounting Plate was cut from ¼ inch polycarbonate on a CNC router. The rest of the parts are…
I created this velocity stack based on pictures I found online. It mates with a K&N air filter (model RU-4410 or RU-2990) There are left and right variations of the velocity stacks. I also added a flange at the end of the stack to the…
If you don't have a locking choke knob on your Austin Healey Sprite, or MG Midget, or other vintage car using this arrangement, you might be using a clothespin to hold the choke in position. This simple clip is slightly more elegant. One…
4 hole tapered and radiused carb spacer. Bores are for 650 to 750 Holley and 750 Edelbrock. Single plane intake all 4 holes intersect. Dual plane, only front to back holes intersect. PETG may be a bit too low temp depending on…
This is the gasket that goes on the bottom of the carbs where they mount up to the ski. I needed them and didn't want to wait for shipping. They are holding up really well so far. Must be printed in TPU. The part should be all bottom and…
Choke part to carburetor for HONDA XRV 750 - 16046-MAY-000.
This Dell Orto carburetor cover allows direct connection to the original intake of the Babetta210 moped, after replacing the original Jikov carburetor. It can also be connected directly using the original connecting elastic tube. This…
Large knob to make adjusting the idle speed on Keihin carburetors possible without a screw driver. The knob presses onto the plastic knob supplied on the carburetor.
My motorcycle choke lever broke, so I designed one, but better. I suggest printing it with 80% or more, to make it stronger. This model was made in Fusion 360, feel free to ask for a custom model.
The service stand and cup (for up side down position ) for Honda CN250 carburetor - KEIHIN VE. The main stand has slot in the base for convenient attachment and top clamp so the carburetor body can be hold in tilted position. The cup is…
These are knobs to slip on to the low and high fuel adjustment knobs to Ryobi(and others) Carburetor. I used a Ryobi R09050 blower for testing and fabrication. I also included the blend file that I created the peices so you can modify in…
I printed this in TPU at .2 Layer height. It's been installed in the carb and working for more than 6 months as of this writing with no leaks or issues. Print this at your own risk, I made this because I was in a bind and needed a part…
weber/dellorto carburetor jets holder simple design but very useful to keep everything organised check my other project too im not a professional designer but im learning have a fun ;-)
This is the simple cutting jig for carburetor BVF 16N1 rubber seal. 1. use cutting templeate to cut the inner shape 2. use the other parts to fix the rubber and cut the outer shape. Printed from PLA - 0,2mm
A joint for attaching two rods at right angles. Designed for a retort stand, but could be used anywhere you need to join two rods. The body part comes in different sizes to suit different diameter rods. To make a complete joint you will…
HIGH-VISIBILITY CARBURETOR CHOKE KNOB – PERFECT FOR COLD STARTS This 3D-printable carburetor choke knob is designed to replace missing or broken cold-start pull knobs used in carbureted engines. The knob provides a comfortable grip and…
Adapter I created to connect an existing choke cable to a Nibbi carburetor choke plunger. Print with ABS or other filament with high temperature threshold as this part will be exposed to heat. Probably wouldn't be a bad idea to wrap some…
A printable float bowl gasket for the Yamaha Enticer snowmobiles with a rectangular float bowl. I used Ninjatek Ninjaflex TPU (85A) I then covered the gasket with parchment paper and uses a clothes iron to smooth the top surface, This may…
Print with threads pointing upward and with layer height < 0.20mm so that the threads are finer Recommend > 3 perimeters No supports required Brim would be a good idea
Simple gasket for printing in TPU
Float gauge is designed for a Goldwing GL1100 but should work for any Keihin carbs of the same design. They were used on a lot of UJMs.
I printed this with prusaslicer, flexi setting for the filament. The 0.1mm detail works fine for me. No brim I have already installed them, if it doesn't work satisfactorily I will remove this. This is a test and I am not responsible if…
Gasket for the carburetor bowl on a cheap 4T (4 stroke) GY6 engine. Made it wider than the original on some spots where the gasket had empty space in the carb bowl groove.
This Backplate gasket is made specifically for CV carburetors and is used between an air cleaner or backing plate and the Carburetor. These should be replaced when installing a new air cleaner. Print in TPU, brother.
Original description from creator: Based on the two good screencaps I could find from Legend of Vox Machina. This is the Retort Pistol that Percy either rebuilt or redesigned off of Ripley's pepperbox. I could only get a look at the…
I needed a new float chamber gasket for my Datsun 120Y (B210). The previous one had deteriorated too much and it was hand cut anyway so it had tears and poor holes for various jets etc. This new gasket was made by scanning the carb on a…
I'm on and off tinkering on my NSR50 project bike. I want it to be as stock as possible, but original carburetors are surprisingly hard to come by (or ridiculously expensive), so as a temporary solution I designed this custom spacer to…
Carburetor Adapter Plate with Vacuum For Kohler SV600-3224 by RebelTaz I swapped engines on a Cub Cadet in my shop without thinking it through first. The original blown engine utilized a vacuum operated fuel pump because the tank was in…
Gurtner PY carburetor float used in a lot of 50cc mopeds. I designed this one for my Peugeot Ludix because my original carburetor float broke and a new one is rare and expensive Print flat on bed with supports all around with a 0.1 or…
What is that? Intake manifold / carburetor gasket #09 for Honda Z50 Monkey. Fits the original Honda 16100-165-924 carburetor. I printed mine in PETG and the other option in TPU. Both materials are equally suitable. When using TPU, no…
This custom designed velocity stacks fit on vintage solex carburetors. The top part can be taken off in order to put in some kind of grid (I cut up some old sieve) to keep debries out of the intake manifold. A custom die to shape and cut…
I have made a nozzle for DellOrto and Polini CP carburetors Flange that offers possibilities With this flange you can easily mount the Polini CP, DellOrto or carburetor The flange is mounted on the nozzle and then the carburetor is put on…
A short bellmouth/velocity stack intake for a 50cc scooter (a Piaggio Fly 50cc 4T in my case), has a 30 degree corner adapter to fit under the plastic trim piece to seal up nicely. I had to rejet the carburetor up about 4 points and it…
Motorcycle carb air filter connection/housing/etc my carb has an inlet pipe thats 44mm I had done the voronoi skull first, worked well for years. I used a different skull i found online, just becuase it seemed to perhaps let less rain…
carburetor spacers SZC 38 for pwk 34 lanza tpu
Replacement 3D printable choke arm for 1979 Honda CB650 motorcycle
Print in FLEX 70 % infill does not have to be super flexible I used cheap Chinese flex from amazon. best printed with the location notch down.
CZ Těsnění pro karburátor legendárního mopedu stadion s11 a s22. Tiskněte z TPU nebo jiného flexi materiálu (doporučuji otestovat zda se nerozpouští v benzínu). výplň 100% ENG Print out of TPU or other flexi material (I recommend testing…
Assorted holder for different size M5 threaded carburetor jets.
Main Body Gasket (Throttle Body Gasket in OEM Diagram) for the Rochester Monojet carburetor. There are other versions of this Gasket for different versions of the MonoJet Carb Family, but this one matched the chinese knockoff carb I…
Udělal jsem škrabku na čištění atoskel od námrazy a jako bonus je s logem Pretoria Stud z Hynčic nedaleko Hanušovic. Výhodou je, že lze břit škrabky jednoduše vyměnit za nový. Můžte si také vyrobit svůj břit podle svých představ.
2 pcs screw M4 x 12 mm 2 pcs nut M4 nylon hose diameter 4 mm manometer https://www.aliexpress.com/item/4000297036291.html?spm=a2g0o.cart.0.0.3fbb3c00d37y3T&mp=1&fbclid=IwAR1Oem6KbuwMDH\_mbio5jrwT1NGR4HzC-9qfDTRg70S3GYcf-yJHQQGxxJY…
Nissan Terrano KA24E intake manifold adapter for weber 32/34 style carburettor - don't ask me why, here is the model Carb used - fiat 125p / fso polonez / zuk licensed weber 32/34 Print it with 100% infill, preferably with petg or some…
pour remplacer le joint d'origine imprimé en TPU pour carburateur Walbro K10-HD n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir ! Bon print !
This is a carburetor adaptor for MTD engines which comes on a lot of Troy-Bilt and Craftsman snow blowers. This adaptor lets you test and tune the snow blower without the hassle of putting it all back together. Printed with PLA, 3 wall,…
Mostly exact copy of a Seadoo Speedster 1996 carburetor cover clip.
I Printed it without enclosure with Prusa MK4S Material: Fiberlogy Nylon PA12 Layer height: 0.2mm Perimeters: 8 Infill:100% Supports: Yes Draft shield: Enabled Brim width: 10mm Satin sheet Heatbed temp 110c Nozzle temp 265c Printing…
A PET Cap with a Boss and 3 Holes to make a simple but very accurate Carburetor Sync Tool, you only need 6mm (or ¼") clear Hoses and a PET Bottle for each Carburetor(throat). Insert 1 Hose in a Cap Hole from the Top until its flush or…
I designed caps for the carburetors of my spare engine of my BMW 3200 CS. Much better than covering them with some pieces of cloth. Fits also the Solex PAITA 32 from several Mercedes models. Best to be printed in TPU. Flip the model in…
The original model lifted from the build plate when I printed it. I think it may have been because it was too thin. I increased the thickness to 6mm.
I needed to get the intake gaskets for a SL 750 and didn't want to spend the money on the gaskets since they aren't exposed to anything but air and mild heat. These need to be printed in TPU and should be all bottom and top layers with no…
What I Used: Polymaker TPU 95A Amazon Basics TPU setting If you wish to donate, it will help me with my journey to create more files for all of you Thank you : https://www.paypal.com/donate/?hosted_button_id=FRD499EASX35Y
Jednoduchý přívěsek s logem hřebčína Pretoria Stud z Hynčic nad Moravou, který se věnuje chovu Welsh Cob. Model obsahuje poměrně jemné linie, pro jeho lepší zhled bych doporučil tisk s tryskou 0,25 mm. Ideální je i použít dva vzájemně…
a imprimer en TPU seal N° 18 n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
Printed with Tpu flat on the bed. Now with pull tabs
Cover is secured by HEXM5 bolt with length about 25-30mm. Available is version with embedded Husquarna logo or without logo. Available is knob for securing filter cover. Might be also suitable for various Husquarna models.
This is a simple 3D-printed adapter that allows you to fit a Honda XR100 carburetor onto a 2001–2003 XR80R while still using the stock XR80R intake boot. The XR100 carb provides improved throttle response and reduced bogging on the XR80R,…
This is a 3d scan of a Mikuni PHH 40 dual barrel side draft carburetor. I believe the Weber side draft is also a direct drop in replacement as far as the flanges but don't quote me on that. This is one of two carburetors, and doesn't have…
This gasket can be printed in TPU with the following settings. It is a direct replacement to a factory seal and has worked perfectly on my own personal 1971 Honda CL175 Scrambler Print speed - 30mm/s Cooling - first layer only Nozzle Temp…
This plate will hold an SU carburetor needle in a repeatable position so that you can mark the stations for polishing/modification. The needles vary in length, so yours may not go to the bottom of the plate and the number of stations used…
A simple fixture to hold a bank of carburetors during bench service. The stl's are sized to hold a Yamaha XJ 750 / 650 carb bank but I have included the parametric FreeCad files so they can be customized to suit any similar bank (to…
printing from PETG plastic or ABS
I accidently put a hole into the carburetor's diaphragm on my tiller when putting a new primer bulb on. I didn't realize until the engine kept flooding. So I went to Fusion360 to see if I could make a temporary diaphragm by tracing the…
Because lab equipment is expensive. For 20 x 20 mm aluminium extrusion with 6mm T & V slot e.g. https://ooznest.co.uk/product/t-v-slot-aluminium-extrusion-profile-20x20mm-cut-to-size/
Just a small part I needed to make for a spacer so the bolts held the carb snug to the body.
à imprimer en TPU n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir ! Bon print !
TPU gasket for my Yamaha YBR 125 ESD 2014 carburetor bottom cap. My old one was leaking. Couldn't find a new one so I built this. Now it is leak free. Image is not the one that I printed but the old one. (Sorry for this but I already…
This small work stand has two pegs ~30mm apart for holding Zama carburetors. The one I'm currently working on is off a Stihl MS261c, I'm not sure the exact model. The vertical piece should be printed on its angled base for extra peg…
Float bowl gasket G170 for Holley 1bbl carburetors 1904, 1920. For Chrysler, Ford, IHC and AMC applications. For temporary use only! Buy official product from supplier! Filament: gasoline and heat resistant TPU/TPE. I recommend avoiding…
Designed for short choke cables on CV carburetors. Often the rubber boot on those short cables can deteriorate, but the cable is just fine. This allows the cable and housing to operate smoothly without this rubber boot. Snaps onto the…
If you remove all the VOES sensor and the other vacuum line off your CV carb you'll be left with two nipples (one brass and one plastic) that should be covered. Print in TPU, brother.
5.125" base, 2.5" inlet tube. 5/16" hold down bolt pass thru hole. Thick walls.
A support piece for the air filter of the carburator for a Guzzi 65cc It can be printed in PLA or TPU 95A, both have enough resistance to gasoline, and bein the air inteke is should not be a problem, i prefer TPU for the physical resistance
The connecting link of the BMW carburator can break and can be very hard to find. That is why I printed it and through an iterative proces I found the correct fit. So it fits tight but it is still smooth to operate. You also need to tap…
When repairing the Parsun F2.6 outboard carburetor, I noticed a missing cap. Without it, the engine would flood after a short time. The original cap is probably rubber, but I replaced it with one I 3D-printed in TPU (I used Creality…
Intro This is a fully open source with CAD provided lab and retort stand that you can use FreeCAD to natively change key variables like the size of rod you want to use. I hated that all existing designs didn't feature counterweights to…
Very simple part, just remove the stock air filter and bolt it on. Be aware that this part is directly exposed to fuel when installed, that means you need to print it in a material that has enough chemical resistance against fuel (like…
Deutsch weiter unten: Adjustment tool for the warm-up enrichment curve of a Golf II. This tool, identified as Part No. 4.07360.02, is specifically used for the basic throttle valve adjustment and warm-up enrichment curve on Pierburg 2E2…
This is a 3d scan from a Mikuni TM40 or HS40. I believe it came from a harley but not positive. Do something cool with it and share some pics!
