Liczymy pasujące modele…
I needed some brackets for the Dell Optiplex 3020M SFF PC, I found 1 other design but it didn't fit and wasn't exactly what I needed, so I designed this. Its Simple and effective. one bracket will hold it up but two is safer! Printing:…
remixed from HP Elitedesk 800 g2/g1 SFF Server Face by magicGnome96
Use these models to mount up to 7 or 9 2.5" SSD (SFF) drives to your 120 mm fan. Or mount it directly to the case in place of a fan. Disk mounting holes for standard SSD M3 screws. Print with the backplate against the build plate. The…
A stand to hold a HP EliteDesk 800 G4 SFF vertically.
This is version 2 of the 2 Fans Mount for the BeamCaseSFF with mounts for 120mm and 140mm fans. -Depending on the orientation of your case, these are either top or bottom case fans mount. they are especially put on the same side as the…
An optical disk drive cover for the Dell Optiplex 5050 SFF
This bracket allows you to use the power supply out of a Dell OptiPlex SFF computer in a case which takes a standard ATX one. Despite its strange dimensions, its outputs conform to the ATX standard. You'll need 7 screws; 4 to mount the…
UPDATE2: Added version compatible with Maxsun Terminator B850 BKB motherboard UPDATE: Fix on current main model to fit better the RTX 5060 backplate mount. I added a wider version for main and front panel wich makes this model compatible…
it uses original screw - just place it under stock sensor.
I used this in both an OptiPlex 7010 SFF and a 3020 SFF but it should work in other similar computers. The outer 3.5" holes are for the pegs in the 3.5" blue drive caddy thing and the inner ones for the 2.5" drive. The clearance holes are…
It's just a simple redesign of the original to meet my requirements.
RST99 – 3D Printed SFF ITX PC Case A compact, fully 3D-printable Small Form Factor (SFF) PC case designed for high-performance hardware in a minimal footprint of just 9.9L. RST99 compatibility: Mini-ITX motherboard SFX PSU 240 or 120mm…
This is version 2 of the 2 Fans Mount for the BeamCaseSFF with mounts for 120mm and 140mm fans. -Depending on the orientation of your case, these are either top or bottom case fans mount. they are especially put on the same side as the…
This is a remix of a thingiverse file to fit 3 hard drives. I made an optional 80mm fan bracket too. https://www.thingiverse.com/thing:5894917 Go rate the original if you like it. They did a great job.
BeamCase is a system that allows you to create your own case with the combination of 3d prints and Makerbeam XL profiles (or similar 15x15 aluminum extrusions). Beamcase SFF is a system optimized towards compact builds with good cooling…
You need 4pcs M3x6 countersunk screw to fit the drive in the caddy. Tested servers: FUJITSU Server PRIMERGY TX120 S3 SFF FUJITSU Server PRIMERGY RX100 S8 rack server FUJITSU Server PRIMERGY RX1330 M1 rack server FUJITSU Server PRIMERGY…
I'm building a PC for a friend and need to validate that all his parts work. I also wanted something that would be compact for simple hardware verification. I quickly made up this test bench to support the motherboard. It sits on top of…
This is a toolless caddy/mount for a 3.5 inch HDD in an HP EliteDesk 800 G4 SFF ( no hardware required ). This mount should fit almost all 3.5 inch HDD and should also work in other HP EliteDesk and ProDesk computers. It is meant to…
Thorzone Mjolnir inspired case. Case is held together and reinforced by threaded rods providing the needed stiffness and structural integrity Most parts prints flat and only a couple needs minimal supports. Black parts are printed with…
Insert and fixate (using superglue) a small stainless-steel/aluminium rod for the hinge-mechanism (only on the outer! hinge-parts). Be careful using the hinge – push the caddy completely in, before locking it. I tried to replicate the…
I bought a used GPU for my arcade build at a price that I couldn't pass up. The only issue is that is was missing the Low Profile Bracket with it. Emblem Fits this Dell OptiPlex Case: Dell OptiPlex 9020 Small Form Factor (SFF) Tower This…
Yes, it was as fast and ugly as it looks! 1 block shape tinkercad model! Made for my G9 HP Pro SFF PC as the desk is small and nothing to hang a hook from! to horse belly is 96mm (3and 8th inches) Kinda looks like a horse… Print in…
UPDATE: I uploaded the v2 of this model, easier to print and assembly. Compatibility with 3 fans 92 and 80 mm ( SFF Mini ITX Case v2 by jagondela | Download free STL model | Printables.com ) UPDATE: Fixed some dimensional issues in the…
An optical disk drive cover for the Dell Optiplex 5050 SFF
Works at least with the Huawei FusionServer 2288H V3, but probably other Huawei server models. Standard 3.5 inch bay (frontside) Standard 2.5 inch (SFF) bay (backside) 3.5 inch to 2.5 inch adapter caddy They are all toolless, design to…
The case measures 25x20x9cm for a total volume of 4.5 liters. It supports coolers up to 70mm in height, and low profile GPUs with a total length of 185mm. This case is meant to be used with a HDPLEX 250W GaN PSU or picoPSU or any clone of…
I was recently able to get my hands on this case and plan on making it my on-the-go LAN PC so I made a handle for it. M3 nuts and screws of varying length were used for mounting. May want to use either Loctite or locking nuts to ensure…
Use tin Snips to cut out the top of the lid and glue the overhang. I found a significant drop in CPU/GPU temp with the lid off vs on, having this vent should get the required result. The version you need for the Lenovo Mini is: 155x140
This 3D-printed adapter lets you replace a 3.5" drive slot with two 2.5" SSD/HDDs in the HP Prodesk 600 G5 SFF. Printed on an Elegoo Neptune 3 Pro with black PETG took 3 hours and 42 minutes to complete. The print used a 0.2mm layer…
Halterung um einen Mini PC unter dem Schreibtisch zu Montieren. 2 pro PC Gedruckt mit einem Anycubic Kobra 2 Plus in PETG. 4 Wandlinien und 15% Infill Benötigt: 8x 3,5x20mm Schrauben Bracket to mount a mini PC under the desk. 2 per PC…
Print out in petg or abs don't use pla. Should fit on a 220mm bed Need supports on the file called “Front_Panel_Strips" Designed to fit the original model and not a longer one but you could alter it to fit one using a longer bigger case…
Prints without support; Pull tab facing up The Cover is NOT symmetrical, it has a long and short side, the pull tab is supposed to be in parallel with the PCB (as seen in image)
This is my original design inspired by some modern more expensive cases. There are two versions for the panel: the standard 330mm length and the extended version for 350mm. This was made such that I can put two 120mm fans on the top or…
2 120mm Fans Mount for the BeamCaseSFF depends on the orientation of your case, these are either top or bottom case fans mount. they are especially put on the same side as the gpu, either to the back or to the front . if you have 2 slot…
Wanted to add some options for 3D printing case feet for the NCase M2 to give a classic mounted GPU more airflow. They reuse the screws that come with the case, and can be printed in 10, 15, and 20mm heights. If you have SolidWorks, you…
Ever thought about mounting a Small Form Factor Dell Optiplex 5070 motherboard in a full-sized tower? Do you dream of PCI slots not aligning correctly and needing custom adapters to make them fit? Are you an electronics hoarder itching to…
Self explanatory. SFF to LFF converter for two SFF drives. Use print softwares mirroring to print other side.
A bracket for mounting HP EliteDesk 800 G3 power supply inside CoolerMaster NR200/NR200P case. I don't know if this is the best placement for the PSU but I wanted to get it done as quick as possible so I took 2 models and remixed them.…
A bracket for HP EliteDesk 800 G3 SFF motherboard for mounting in Cooler Master NR200 NR200P cases. It's likely you can also use it for mounting inside other mATX and ATX cases but I have not tried it myself. This is a low effort model,…
Backplate to be used with my motherboard offset plate. I recommended printing it with some higher temp resistant filament like PETG. I've used orange Prusament PETG. I personally have RX6400 GPU so there is an additional cutout for…
I made this caddy for two 2.5inch hdd sas drives for lenovo m800 sff.
These are my panels for the BeamCaseSFF extended to 350mm because that is the length of my BeamCaseSFF (using 320mm aluminum x profile beams). these are inspired of some itx cases that exist on the market (ex: nanoq). Notes: -I use the…
This is a simple low profile bracket for a PNY Nvidia NVS 510 Quadro GPU, designed to fit an Optiplex SFF computer.
This is a hybrid between 2 prints I had found on Thingiverse that had ups and downs. The first one fit perfectly, but the front looked horrendous. The second didn't fit well, but looked great. I mixed them and used that to make a cleaner…
Building on my previous 4.9L design, and bringing it to contemporary standard, I present the 5.0L It has the following updates: Removed all heat inserts. You can build this with normal M3 nuts Can be built with one screw pack! No more…
I bought the Secretlab Magnus Desk with the Premium PC Mount. I noticed that the PC mount does not support small form factor pc cases (like nr200p max). So here is an adapter you can simply click against the existing metal plate to extend…
This bracket allows you to use the power supply out of a Dell OptiPlex SFF computer in a case which takes a standard ATX one. Despite its strange dimensions, its outputs conform to the ATX standard. You'll need 7 screws; 4 to mount the…
Stačí použít běžné šrouby co se v PC používají, jak do zdroje, tak i do plastu, tam si vyřežou samy závit a vše pevně drží. Je to i navržené tak, aby dva šrouby držící zdroj (aspoň v mém případě) držely i za plech, tudíž je to o něco…
My printer settings: Filament = ABS Layer hight = 0.2mm Infill = 16% Support = no Wallcount = 4 Material: 1x ATX Power Supply 1x Used Oculink PCB: cablecc 4X OCULINK (…
I designed this wall mount for the HP EliteDesk 800 SFF to integrate it into my homelab setup. This mount securely holds the PC while keeping it off the desk and out of the way. Printing & Assembly Instructions To use this mount, you'll…
Introducing the Mantis Mini, this is a fully 3d printable pc case utilising a flex atx psu, low profile gpu and itx motherboard. Measuring 193.5 x 118.5 x 193mm this is a compact case which will fit in most small spaces. This case…
This remix adapts the original caddy from the HP series servers it was designed for to a Hitachi HUS (Hitachi Unified Storage) SFF 24 bay drive chassis. The drive bays are deeper than typical Dell or HP servers and hard to source (200mm).…
What - Extendable SFFPC case design - can handle GPU up to 380mm with ease. Why - Future compatibility. How - Utilized MakerBeam 300x10x10 Alum. extrusion rails. 3D printed Frame offers some extension so your long gpu can fit…
2U DAP panel cage for smaller NUC/MFF computers This is a maximized holder of computers of many sizes into DAP panels where the holders can be mounted with Vesa 75 || 100 plates for extra stability. DONT FORGET washers for the screws/nuts…
You can attatch a 120mm fan to the front side of the pump. If you are using FormD T1 and 120x15mm fan, GPU slot configuration has to be less or equal than 2.5-slot. You have to remove transparent cover and silvery second cover (you can…
Was unable to find a commercial right angle connector but was able to bend the cabling with this support.
Lets you put two 3.5" hard disk drives in this small form factor chassis at the expense of the optical drive. Bill of materials: 4 M3x4x5 threaded brass inserts 5 M3 screws: one for to replace the stock large standoff, four to secure the…
Vertical feet to stabilize an HP ProDesk 600 G1 SFF - will work with anything around 100mm/4in wide. This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/kG8sfFpiA9F Print Settings Printer Brand: Anycubic…
Introduction to this project: It is a case replacement for the ASRock Deskmini series STX motherboards. I needed a powerful desktop processor and yet in a compact form factor. The original Deskmini case was too large for my liking and did…
In this case, it's a Precision 3430 SFF. The original PSU passed a way. I decided to make some improvements, such as adding a graphics card, and for that, I needed to replace the ATX PSU. However, since I wanted to install it in a…
Designed for HP Elitedesk/ProDesk 400/600 SFF models with a single 3.5" HDD bay, it holds up to 5× 2.5" HDDs in the 3.5" and DVD slots. For better cable management, it’s recommended to install only 4× drives and leave the bottom slot…
Designed for HP Elitedesk/ProDesk 400/600 SFF models with a single 3.5" HDD bay, it mounts 2× 2.5" drives under the existing 3.5" cage. The DVD drive must be removed to install this bracket. Spacing is very tight, recommended for SSDs or…
A stand to hold a HP EliteDesk 800 G4 SFF vertically. Has holes to save filament and allow the stand to be placed around the feet of the PC.
For mounting a flex ATX PSU to a SFF Dell PC chassis. The left (single tab) of the PC chassis needs to be removed. Using a flush cutter and a file works well. The flex ATX PSU mounting holes are clearance holes for standard 6-32 screws.…
A cover for the power light of an HP EliteDesk 800 G4 SFF
his is the case for a luggable, all-in-one SFF PC, which is an homage to and inspired by the Compaq Portable line of computers. The design phase of the project took a couple of months as an exercise in learning FreeCAD. The internal…
Low-profile cap for Corsair Titan RX AIO cooler (240/280/360/420), designed with small form factor builds in mind and any setup where space above the CPU is limited. Compared to the stock cap, which adds over 11mm in height, this design…
Lots of time spent to get fitment right and some sanding will be needed… The whole idea is to densify hard drive storage space in a small form factor machine that can be used as a NAS or network area storage server on the cheap. There is…
Overview This is a fully functional, vertical Mini-ITX slim PC case designed specifically for 3D printing. I created this case to build a compact, powerful, and unique gaming PC that can stand alongside modern consoles. The design is…
Overview This is a custom 3D-printed conversion bracket designed to help you upgrade your Dell PC's power supply. It allows you to replace a proprietary Dell SFF (Small Form Factor) PSU with a more powerful and widely available Flex PSU,…
UPDATE2: Added version compatible with Maxsun Terminator B850 BKB motherboard UPDATE: Fix on current main model to fit better the RTX 5060 backplate mount. I added a wider version for main and front panel wich makes this model compatible…
Lenovo has a common SFF chassis that covers many models of thinkcentre (e.g. M710s, M720s, M900s, M910s, M920s ) ideacentre and other value ranges such as V-series like V530 and they only change the front panel/bezel according the model…
NOTE: The case design is functional, but not perfect as I didn't want to waste any more filament on testing--I stopped at “good enough”. The clearances around the IO panel are not great, the internal ssd retainer only manages to keep a…
Allows using standard 3.5 inch HDD screws (#6-32 UNC) in your EliteDesk 800 G5 3.5 inch bays. My screws came in a standard motherboard screw set and are 6mm long. The adapter is sized after the original HP screws and fits well. Printed in…
This model is for mounting 3.5" HDD to HP Elitedesk SFF. It requires #6-32 screws. I use 3/8 round head screws. My HP Elitedesk SFF is a G3. My understanding is other generations use similar bracket and the model should work, but I have…
Video: https://youtu.be/IR4NWpqXP5c All of my previous PC case designs have been for ITX, but with every design I have been asked if it can work with ATX/microATX. This was mostly due to the maximum print size on many printers, so I…
Video on case: https://youtu.be/WR7D76tS818 Video on creating new parts: https://youtu.be/goCXNFvoNAs Was looking for a case that would make a great NAS system, but wasn't finding anything SFF. Took what I learned from my open-frame case…
Video on case: https://youtu.be/p2pK2BuXsXg Had been noodling around with creating an Open Frame case for a while now, but after seeing this case ( https://www.instructables.com/id/Open-Frame-Mini-ITX-PC ) I finally decided to make one.…
Video about project: https://youtu.be/iKGNek3DkK4 My second case design, this one focused on required the fewest extra parts as possible. I already had a parts list in mind so this isn't the smallest I could make it, but had a few…
Video of project: https://youtu.be/p55gvl1gWus See my other case designs: https://www.thingiverse.com/lightofhonor/designs I wasn't thrilled with the price of the very small SFF cases so I decided to take a stab at designing one myself. I…
Video about case: https://youtu.be/NaJl-yomTfQ See my other case designs: https://www.thingiverse.com/lightofhonor/designs While SFF PC cases are now cheaper than ever, GPUs are still more expensive than they should be so I designed a…
I wanted to print out the original in a single print, so I took a chunk out of the psu section and it now fits inside the main part. It also uses less plastic, and should take less time to print as well. How I Designed This I used…
A single 2.5" HDD mount for dell SFF inspiron. A lot of other hdd mounts were focused on optiplex SFF mounts so I created this one.
Summary These are the side panels for the Beamcase SW 3.0 PC case ( 2 GPU slot / IFW 140 size ) (by @BeamCase_Des_1734300 ). I was strongly inspired by the Beamcase SFF Side Panels (by @Fastrunner07_2540939 ). Aim of this remix is to: Add…
Hello everybody, my latest project is an SFF computer with a volume of around 7.4 liters. The hardware components currently installed are not the best, and I plan to upgrade at least the GPU in the near future. Specs: MSI B450I Gaming…
For this you need: Screws 6#32, I recommend to buy long screws and cut them with tweezers or dremel: 6 for external shroud (8mm long) 4 for motherboard (5mm long) 4 for PSU (8mm long) 1 for GPU hold (5mm long) 2 for USB ports (5mm) 2 for…
After modification of the metal case, we can use this mount to install 2 HDDs above each other.
1) Printable on regular 3D printers. Printable on an Ender 3. 2) Have as much as possible 3D printed. Other than case screws and a power button you shouldn't need any other pieces! 3) Print with zero supports. Hate removing them, so…
Ultra-Low Profile 90-Degree IEC C13 Plug Designed to solve extreme clearance issues in SFF (Small Form Factor) PC builds. This custom housing allows for a C13 power connection in spaces where even "slim" retail 90-degree adapters fail to…
This is a front bracket that can be used to mount a FlexATX PSU at the front of a BeamCase SFF. This enables very short builds with 200mm beams, while maintaining full air cooler support. This bracket is only compatible with standard…
A vertical stand for the HP Prodesk / Elitedesk SFF models. It should work with any G3, G4, G5, G6 Prodesk 400 / 600, Elitedesk 705 SFF. Print settings: 3 perimeters PLA or PETG (I used PETG) 20% infill
Very simple model, but also very useful, at least for me. With everything with flash memory in low supply and crazy prices these days, the only cheap NVMe drives I found were 2230. I knew the motherboard of both the HP EliteDesk 800 G4…
it uses original screw - just place it under stock sensor.
I used this in both an OptiPlex 7010 SFF and a 3020 SFF but it should work in other similar computers. The outer 3.5" holes are for the pegs in the 3.5" blue drive caddy thing and the inner ones for the 2.5" drive. The clearance holes are…
It's just a simple redesign of the original to meet my requirements.
Hola, este diseño actualmente esta en test por ende no puedo garantizar que funcione pero en teoría debería el gabinete tiene una capacidad de 3 ventiladores, 2 de 92x25 al frente y uno atrás de 80mm ,capacidad para una placa ITX con un…
RST99 – 3D Printed SFF ITX PC Case A compact, fully 3D-printable Small Form Factor (SFF) PC case designed for high-performance hardware in a minimal footprint of just 9.9L. RST99 compatibility: Mini-ITX motherboard SFX PSU 240 or 120mm…
