120 modeli
This is a replacement for the air stripper and baffle assembly on the Umarex Gauntlet pellet rifle. Prints in one piece, muzzle-end-down with no supports needed. I saw a noticeable decrease in firing noise after replacing the factory…
holster for the hdr 50 umarex revolver
This little gizmo helps you load BBs into your Umarex USA Glock 19 .177 (4.5 mm) Air Gun magazine(s). Assemble the loader by attaching the threaded funnel to the guide (the walls of the guide should be facing away from the funnel piece).…
wanted a free handguard so I made my own didn't like tri-picatinny rail so I did it with M-Lok so it wouldn't be too bulky. printed in two parts so it's easier to install. feel free to improve the design, I'm new to this. if you improve…
Disclaimer : This design is intended for use with Airsoft Guns ONLY and NOT for real firearms. Safety Note : Always wear appropriate protective gear, including eye protection, when using airsoft weapons to prevent injuries. Use Caution :…
Precise Slug for Umarex t4e HDR50 This is my design on slug that I have tried on my TR50. Remove support after print is finish like on images! Then simply place the 8mm ball on top and with a little pressure it will click into position.…
Easy solution for mounting a bipod on an Umarex NOTOS. Slides over the air cylinder with no modification to the gun. Included the Solidworks file if you want to modify it at all.
Smaller Version Cal 50 with 4,5mm Steel Bullet For Umarex HDR 50 Home Defence Revolver T4E
here is a Pouch for 5 HDR 50 cylinders. that can be mounted on the molle system. to load it slide the top open. place the 5 cylinder in there. and make sure they don't flip over. than you can close the lid. and your ready. this van be…
Softair bottles arrives usually in carton boxes, once a few have gone the remaining ones wander around and they are under pressure! this canister keeps them in place, full capacity is 13 but, because I carry also maintenance oil bottles,…
Umarex T4E 68 bullet for 12mm sphere
I have had great success making these of PLA with 3 perimeter walls and 20% fill. Print picc rail down with supports and you should be fine. You can also order them printed and with all the hardware installed at the targetforge.net…
Umarex T4E 68 bullet for 8mm sphere
I designed 3 mounting options of my magazine holder for the Umarex Gauntlet. These mag holders mount to standard picatinny rails. They are two part prints that are held together to the rail by a standard M4 bolt. The hole for the bolt is…
I wanted to test increasing the sound suppression on my Notos without chopping off the stock moderator. So I made a new insert with more baffles that can be used stand alone without the external suppressor. This baffle insert increases…
I really liked MysticalDork's Umarex Gauntlet integrated moderator , and wanted to test to see how well it would work on other airguns. I had mixed results - seems to work to reduce sound (though less than an enclosed unit), but I am…
Extended cocking lever with a 12mm and 18mm offset to give more space between the mag and charging handle, the handles are threaded for m5. I haven't had time to test but for basic function and fit.
It adds space for the co2 cartridge plus a bullet storage, so that the cartridge does not fall out, it is necessary to stick foam on the inside as in the photo
Umarex HDP 50 Picatinny rail adapter Gun needs to be disassembled to be able to change the slider mechanism. 0.4mm nozzle - 0.2mm layer height 100% infill for the slider mechanism for max strength (use the same print orientation as shown…
Magazine Base Plate for UMAREX Glock 17 Gen4 – a precisely designed replacement part for Umarex Glock 17 Gen4 replicas. It ensures durability and secure fit. Perfect for airsoft enthusiasts and replica owners seeking reliable spare parts.…
Umarex NOTOS picatinny rail , full length with block screw tab to fix it to the rifle. A more refined version of my first one. Now uses the block screw to attach . Slips over air cylinder on the Umarex NOTOS air rifle adding a pic rail to…
Umarex Ruger 10/22 Spare Magazine, can be used for other .22 air rifles.
Printed mine with a 0.8mm nozzle and 0.2mm layer height. Supports were deactivated without problems, the space in the model is not needed anyway. Careful with tightening of the screws, they will interfer with the magazine if tightened too…
Put the hairpin in to a hole. Inventor sources included.
here is a Pouch for 5 HDR 50 cylinders. that can be mounted on the molle system. to load it slide the top open. place the 5 cylinder in there. and make sure they don't flip over. than you can close the lid. and your ready. this van be…
This thing was made with Fusion360. Fill it with magazins and pellets, shake it, remove the unnecessary pellets, press the diabolos into the magazines, plink! Have Fun It would be nice if you could post a make! ;)
this loading tool is made for 2 magazines(cylinders) so as shown on the picture can you move the pellets to the side in the grove after your done loading. and push the cylinders out from bellow when your done. Category: Sport & Outdoors
Prototype silencer for UMAREX HDX .68 T4E
This is a moderator for the Umarex Notos air gun. This is not for firearms use and only fits on the Notos air pellet gun. This slides over the built in moderator/barrel end of the stock Notos air gun and does not require any modifications…
Remix of original Robert Huebner's hand guard to fix issue with bulky air pump connectors.
A silencer for the UMAREX T4E HDX .68, version 3.0, printed in 3 pieces, designed to screw together but for some weird reason I can not slice the thread so then now it is glued together. It has been designed in Inventor 2025. I included…
I designed this up for the umarex notos that has a huben regular/drop block and a .22L bottle. Bottle diameter = 54mm Barrel diameter = 32mm [12/26/2025] I also added a 61mm bottle step file. This has not been tested. Clamps around the…
Put the 4.5 mm ball in to a hole. Inventor sources included.
Custom compensator for UMAREX P99 DAO airsoft pistol, i just made something i liked the look of, it is not really based off of any real compensator. Needs an M4 nut and screw (i used nylon screws), i also removed the orange tip from mine…
My partner and I were walking through the local Academy on a whim, and I took a curious glance in the section full of airguns and airsoft guns. We both wanted an airsoft revolver at the time, as it seemed like a fun fidget, and we have…
WORK IN PROGRESS! Hi, I created cylinder for Umarex HDR 68 but adepted for ASG. One shoot from HRD will send 6 bb's to your friends in enemy team ;) Cylinder having place to glue 15 rubbers 10x2x6,1mm (width x thickness x inner hole…
Il est pas évident pour tout ceux qui utilisent les armes de défense Umarex T4E Gen 2 de pouvoir serrer correctement le percuteur de cartouche de CO2 alors j'ai fait cette clé de serrage. PETG, couche 0,2.
To be PERFECTLY clear, this is for a pellet gun. An AIR rifle. I love the rifle. Between my boys and mine, we have 3 of them. Not a huge fan of the Magazines though... This holds 3 mags, the filler adapter, and the single shot ramp nicely…
This is a fill probe holder for an umarex notos. I designed this for a guy at work, he gave me some dimensions to work with, I also designed a recess on the side plate for an m3 nut. He told me he slightly modified it after it was printed…
Replacement Piston Piece for HK MP5 AEG Competition cocking lever by Umarex (Elite Force). This part replaces the broken injection molded piece shown in the pictures. Note: you can also break the charging handle itself despite it being…
The rib on the HDS is purely decorative as the barrel selector obscures it in use. This rises the rib by an additional ~5mm and adds a small "bead" front sight. It comes in two parts, the barrel shroud/rib and the action shroud/rib. The…
Źródło oznaczyło ten model jako treść 18+.
There's a great ecosystem of Crosman air pistol 3D prints and I always wanted to accessorize my Umarex Strike Point with a folding stock. This fits onto the lugs at the back of the gun using the existing factory screws and the accessory…
I have a Umarex Trevox airgun for which the rear sight broke. The original sight is pretty fragile (and so is the 3D printed replacement)! I reverse engineered what was left of the original, and tweaked it somewhat for printing. I printed…
This is a kit to turn your HDR68/TR68 marker into a .50 caliber plinker. It is nowhere close to perfect so please take your time to read the description before deciding to print. The kit includes: Stick magazine for ~25 12.4x15mm…
This grip for the Umarex Notos airgun has dual functionality for precision shooting with its 5 position adjustable bipod and vertical angled foregrip. The optional foregrip provides improved ergonomics and control for off hand shooting.…
Print best from PLA, complete part should be made of outer shells. Has anti-elephant foot features implemented, for orientation check picture attached. For assembly instructions check link below:
I do not own 4 cylinders for Umarex CPSport (Walther P22 replica) so i wanted to design my own one cylinder speed loader instead of the square quad one. Just put the cylinder into this loader, get there a few pellets or BB brocks (these…
I was requested to redesign my Stock pad for the Elite Force MP7 to fit the Umarex/Well MP7. I have not test printed it, but it is based off of Planetler's design so it should work. Planetler's design:…
After owning an Umarex Colt Government 1911A1 CO2 pistol (cal. 4.5 mm (.177) diabolo) I found that the right grip (CO2 cartridge cover) moved around a lot and the grips are not that good so I intended to adapt wooden grips from real 1911…
This STL file provides a straightforward, no-frills barrel band for the Umarex Gauntlet 2 version. It is designed purely for functionality, clamping the barrel to the air reservoir to reduce flex and vibrations, which can enhance shot…
This is a custom 3D printed handguard made to fit the Umarex MP5 .22LR. It has a slim, lightweight design that makes your rifle easier to handle and gives it a clean, modern look. Less bulk than the stock handguard, making it easier to…
Sleeve to go over OEM suppressor on an Umarex Notos air rifle. Adds 5/8 x 24 threads to the end of the barrel. Included air stripper cap and blank thread protector. They are plastic threads, so be careful. I added a tiny bit of silicone…
I needed to make a bipod mount for my Umarex Hammerli Hunter Force 900 Combo airgun. I downloaded the bipod from here: https://www.printables.com/pl/model/357606-bipod-for-picatiny-retractable/comments I made three variations of the…
A simple replacement spacer to adjust the belt width in the Umarex HDR50 holster. Fits without glue in a loose friction fit and is high enough to jam against clip when closed. (See pictures) Printable in PLA with no problems. Settings I…
Umarex Notos 1913 Grip Designed for the Umarex Notos. This design has not been tested on the Umarex Notos Gen 2, so compatibility with the Gen 2 is not guaranteed. It’s time for the Notos to lose a few inches! This replacement grip adds a…
just a simple wall mountable stand for the umarex hdp50 pistol
PROTOTYPE, PROJECT Aborted Picatinny Rail Mount PROTOTYPE. Umarex UX SPA60/100. Clamps on, does not hold "Zero" if not glued on, will shift when firing. Does not block Iron Sights. I ended this project because of unsatisfying results with…
This is a barrel band I made for my SL30, it fits fairly snug and is about a thin as you'd want to make one. I made mine in PETG, but other filaments would probably work just fine. If you find that it's difficult to get on or off as the…
This is a dummy training mag for the Umarex 4.5mm CO2-powered pellet gun that uses revolving cylinders inside the magazine. These drop from the gun just by pushing the mag release button, even without additional weights ! This models…
I wanted a barrel adapter for my Umarex MP5SD so I made this. Bayonet fitting to 14 CCW. (Also compatible with some JG MP5SDs) A 0.4mm nozzle works fine for the threads.
Snapped your charging handle with none left in stock? This should get you running again! I made this model taking hand measurements from my own snapped handle. Running it in my own RIF it ran and felt no different to the OEM one. Off of…
filled center for use of guitar pick guard screw. no insert, also back side has the notch to line up. i mixed like 3 different elements of other peoples mods of the original original. lol now i wont need to hunt around to find all the…
This is a loading helper for the widely used umarex 4.5 (.cal177) XBG BB gun. according to online information i found the mags fit into the UX TDP as well. Print the funnel part standing on the wide ring and use a support (only from…
A tool for quickly and easily loading BB into the magazine.
Suppressor adapter for Umarex Walther CS88 pellet airgun. Suppressor thread 1/2"-20 UNF, same as Huben suppressors.
AIRSOFT GLOCK REPLACEMENT GASKET / SEAL- FITS GLOCK MAGS FROM UMAREX pretty self explanatory, should replace the standard gasket/seal for Umarex Glock magazines, probably fits others. Printable in standard TPU, or print in foaming TPU for…
Done with the clamshell for the spa master, now I will work on a foldable or fixed stock. for the clamshell to fit you need to cut of the front "iron sight". I will add a replacement picatinny rail instead of the back iron sight that can…
Replacement muzzle for GLOCK 17 .6MM Cal. Some places around me need this to be required to play in games. Modeled For The Umarex Glock 17 GEN4 GBB .6MM Cal. PLEASE DO ANY TOLERANCE TEST BEFORE COMMENTS! I CAN MAKE CHANGES IF REQUIRED.…
Print in PLA or PETG with a layer thickness of 0.10 or 0.15. An M4x26 screw can be added to secure the assembly.
Needs a 25mm M3 screw and nut. carfully pry the printed clamp appart to get over the saftey pressure release brass screw (you can also take it off it you want, but you have to tighten it proper when putting it back in place or your will…
SINGLE DOT FIBEROPTIC SIGHT FOR AIRSOFT GLOCKS (G19) Unique design eliminates the need for a front sight, and multiple dots. When the sight is on target the dot glows in ambient light, when off target the dot is obscured by the walls of…
Designed these magnetic mounts for my dry fire pistols. They were designed to fit both a Mantis TitanX 701 (G19) and Umarex G19 CO2 BB gun. They also work with a real Glock 19 and Glock 23. Has 2 holes for 32mm x 5mm round magnets. There…
Hello. I designed this Diabolo crown case for my Walther CP99. Printed in PLA without supports with a fill rate of 15%. For the assembly it will take 2 countersunk screws M3x8 or 3x10 no longer. one M5x80 socket head cap screw with…
I have included a early file encase of too tight of tolerances/differences between VFC USP's. Printed in PC with a 0.4 nozzle and I have been printing these upright with the thread at the top and leaning the model back till the barrel…
An adapter/mount for Umarex Ruger mk4 to use any RMR mounting pattern dot sight - print it standing up on the clip side. You'll also need: 2x M3 nut 2x Countersunk M3 bolts - 14mm IIRC 1x Countersunk M3 Bolt - 12mm IIRC Assembly is pretty…
Umarex Notos M-Lok Handguard Designed for the Umarex Notos. This design has not been tested on the Umarex Notos Gen 2, so compatibility with the Gen 2 is not guaranteed. It’s time for the Notos to have more mounting points! This handguard…
I got a few of these rifles as factory returns so none of them came with mags, so I wanted an easier way to test them. The tray is a tight fit in the well so make sure to be careful when pushing it in or out. It has a groove in the middle…
This is a mock suppressor made specifically to fit the Umarex Airsoft H&K USP .45 and is very likely to not fit any other airsoft handgun. I have included 3 different models. MK3 is the final completed model and fits very well and snug.…
a custom 3D-printed magazine baseplate designed for the Umarex Glock 17 Gen 3 .177 BB CO₂ air pistol
Replacement rear dovetail sight for Umarex Colt 1911 and Walther CP88 air pistols. It may fit other Umarex models as well and I will update if informed of it. Two versions: V1 uses single M4x5mm maximum length screw. It was my prototype…
This is a harmonic dampener I made for the SL30. It helps reduce harmonic vibrations, center, and stiffen the shroud and barrel assembly. It is meant to slide over the barrel and allow the shroud to slide over it. Installing is pretty…
took the fusion original file and took some time to modify it to fit my S&T ust45 model
Protective cap for Umarex UX NL 4 laser pointer. Cap prevents accidentally turning laser switch on when it is not needed. When packed this will prevent empty batteries, no need to take them out either. One thumb screw and one M3 thread…
Safety switch for the Umarex SA9 BB gun. Works well but always remember to stay safe around firearm, follow all safety rules and use it wisely. I am not responsible for misuse and the failure of the printed part. Use at your own risk.…
Made this MLOK replacement for the stock side rails for the KWA MP7. Most available models online are for other brands which are mostly too big for the KWA MP7. Do note the MLOK spacing in between the two MLOK segments are reduced to…
I needed a buffer tube style wall (closet door) mount for my Umarex Notos, but standard AR mounts don't work smoothly because the Notos OEM stock has a ridge that gets in the way/isn't perfectly round. This is inspired by Joulez's AR wall…
Protector caps for the 29-round capacity, Elite Force/Umarex USP CM125 Airsoft AEP Pistol magazine. The caps were designed to be printed in TPU plastic so they stretch slightly to friction fit around the magazine. Print Settings Printer…
I didnt have the right size rubber o ring. i made one in tpu instead. i tried 27mm 28mm and 30, 31mm was the sweet spot.
This is a custom Picatinny red dot mount designed for the Umarex Glock 17 Gen3 .177 CO₂ BB pistol. It allows the use of Picatinny-compatible optics without permanently modifying the pistol. ⚠ Prototype / Test Version This design is…
The Umarex Iconix Is a great entry level PCP but its extremely loud, to fix this I have designed this slip on moderator. I designed this for the 22 caliber version but it will work on the 177 caliber version as well. I 3d printed mine out…
15 ROUND SPACER FOR AIRSOFT GLOCK MAGS reduces the round count from 19, to 15, to make it more realistic with the extra benefit of making your mags more distinguishable from others. i dont think i need to explain more. NOTE: metal BBS it…
important Reduced optic height for improved stability. Improved clamping fit and retention. If your print has slight movement due to printer or filament tolerances, a thin shim (such as standard printer paper or electrical tape) can be…
Diameter has been dialed in specifically for HDR/TDR .50 launcher cylinder. You may need to adjust depending on the amount of wear and tear on your launcher. Tip can be left hollow but, it is setup to take a .177/4.5mm BB. Small tail…
Simple adapter to allow smaller 8g Co2 to be inserted, requires a 5p piece to be glued in the bottom so that it doesn't get chewed up.
Will fit In the BB gun Check Pictures. Print Settings 0.08 Layer Height , 100 Infill For Strenght. Might be ok with other This is best for me
Tired of trying to hold your mag follower down when trying to load your magazine? This little print will help you do just that. I call it the Glock Chock. Feel free to remix it or let me know if it works with other magazines. Ignore my…
![[Umarex/VFC] UMP 45 / 9 Charging Handle](https://media.printables.com/media/prints/0ab9e8f6-b743-4314-bff6-de94f3a8e897/images/11616230_5b34de37-2738-448f-993b-029404bb0715_66f0f407-6320-4f47-9fa9-43b2b0869463/20260103_211832.jpg)
