Counting matching models…
I wanted to build a power bank that could support the USB PD protocol so I could charge all my devices off a single battery. I ended up with this 288 W/h power bank using 16 5000mah 21700 cells in a 4s4p configuration and leveraged a 100w…
This is case for 4s2p package and 100W charging board from aliexpress. The power bank board works well on USBC with the PINECIL and PINECIL v2 device on 20V+. The LED display was desoldered from the PCB and glued to the housing on…
Another powerbank case for a popular module from Aliexpress. It is designed to be printed without supports with 0.2mm layer height. Requires 2 M3x10 countersunk screws and 2 M3x12 hex head screws. The screws goes directly into plastic.…
4x M3 x 6mm countersunk 4x Threaded Inserts M3 X D5.0 - https://www.aliexpress.com/item/4000232858343.html IP2368 - https://www.aliexpress.com/w/wholesale-ip2368.html BMS - https://www.aliexpress.com/item/32808335825.html (4S 40A Balance)…
Whats needed to build this ? The 100W/65W DIY Power bank Modules typically available on Ali-express / e-bay etc. (Model : MYZL-YD24-2.32) 6x M3*4*5 mm Heat Set Inserts (installed on the Base to secure the Lid) 6x M3x8mm Flathead screws…
Mount with screwholes for Baseus GaN3 Pro 4 Ports Desktop Charger 100W. I needed a simple sleeve mount so I can put the Baseus charger under my desk, where I can still easily get it out and take it with me. There's 2 versions, one which…
This is a remix of PARKSIDE X20V TEAM RD DPS3005 PORTABLE 100W POWER SUPPLY of the user JAAANIK uploaded to the cult3d web with a couple of usb charging ports added. I leave the link to the original model. All thanks and greetings to the…
This 144Wh 100w USB-PD power bank is the the little brother to my 288Wh version . My main motivation was to have a large power bank that I could travel on airlines with. The TSA regulation is 160Wh max . I ended up with this 144Wh power…
This is a simple case for a powerful powerbank module from Aliexpress and 5S 21700 battery. The assembly requires 4 small screws. The model is designed in FreeCAD. The source file is included. The supports might be needed for the screw…
Adaptation of a power bank PCB from Aliexpress with all major quick charging protocols and cell balancing. Holes are almost necessary. Heat output is around 10w in the worst case scenario. Cells overheat at maximum charging power even…
The case is suitable for assembling 5S2P and anything smaller. Total 5 parts 1 - Outer case 2 - Substrate for mounting the board 3 - Back cover 4 - Front cover 5 - Rib/separation of the board and batteries (can be fixed with glue) For…
Vertical holder for Ugreen Nexode 100W charger. It includes cable holder to prevent damages on the USB C plugs. Print with supports. Stick it to the wall with double sided tape. Slots for cable should be able to take the Ugreen 100W PD…
Components you will need: 12x18650 cells, BMS preferably over 20A, power bank module(link in the description), cables that can withstand over 10Amps (the BMS is optional as the power bank module already has one, but i don't trust it)…
Casing for 100W USB PD Power Bank, based on: IP2368 ( https://de.aliexpress.com/item/1005004705604260.html ) Needed: IP2368 board, BMS, 8 18650 Cells, nickel strips, cable, screws. Accents and cable holder are optional. Category:…
A cradle designed to hold the 100W power adapter for certain Synology DiskStation NAS units. Specifically, the model “Adapter 100W_2” AKA “Adapter 100W Level VI” (Dimensions 13.7 x5.9 x3.5 cm, currently used by NAS models DS920+, DS918+,…
Mounts for mounting a 100W renogy solar panel vertically on a wall. Print out of PETG or ABS/ASA. Print the face that would be out down, so no supports are needed.
I designed this 100W USB-PD/A (QC 3.0) charging box which plugs into an Ozito 20V battery. This is ideal as it completely charges up my Macbook and other USB-PD laptops at a full 100W. You can either print the top with USB-PD only or a…
reduction/pass through the enclosure wall for example for this heater: https://a.aliexpress.com/_mPlGPcS I didn't want the heater touching the wooden wall. So I created a reduction and at the same time a passage through the wooden wall.…
The model is one STL, but can be split into parts/objects to print the body and the tabs separately, helpful if your supports aren't perfectly dialed in. The parts can then be glued into the body, (I used ABS glue…super glue, solvent…
Update 2021-02-24: If you're looking for an 88mm height, take a look at Sharkoctopus's remix at https://www.thingiverse.com/thing:4754084 which locks the pieces to each other all the way up. Update 2020-09-23: francisesmodewhite found it…
refer video : I designed this powerful LED flashlight because I felt needs for a strong light in a lightless country life. I also made the high-powered battery pack used for this flashlights. I shared spot welder 3D models with the…
CZ Ahoj! Dlouho jsem přemýšlel čím napájet notebook, páječku, telefon a další zařízení, až jsem objevil modul 100W PD USB C na Aliexpressu a věděl jsem že je to přesně to co hledám. INFO Baterie je v zapojení 3P4S - 15000mAh 16.8V Modul…
Use an Arduino with MCP2515 to Power on the Ebike battery (MCP2515 lib needed) Used the components as described in https://www.printables.com/model/49417-bosch-36v-ebike-battery-connector-diy-2a-charger Isolate with heat shrink and hot…
A case for a power bank control board that fits 25x 18650 or x 26650 cells. You will need these parts: 1x power bank control board - you can buy it on Aliexpress The module is great, with 2 USB outputs, 1x USB-C input/output with fast…
This is a custom-designed 3D-printable case for a 100W DIY powerbank project. It is compatible with a 5S2P lithium-ion battery configuration and includes space for a USB-C PD board. Youtube Video:…
This is a remix of tearandfix's 8 cell 21700 battery bank model , but with the following changes: instead of using clips to attach the two pieces it uses plastic screws (M3*12mm plastic screws from this kit ) it uses a different power…
This is a VERY bright compact 100 Watt LED flashlight. It is powered by a 3s lipo battery and a led boost converter/controller. I have build many powerful flashlights before, but this is my favorite. Parts: The part list for this build is…
Parabolic reflector for studio lighting, it could be mounted on my other lamp designs for standard LED 20-100W modules with 34mm hole distance Focal height 3mm, overall height 200mm Focal height 5mm, overall height 200mm You can print the…
A 100w USB-C Battery Back made for 18650s, with a Switch and 2 additional USB-A ports. The pack is made for an 4s4p battery configuration. I have gotten a USB-C 100w Soldering iron and it holds up Ok, albeit struggling at higher loads…
Adaptation of a power bank PCB from Aliexpress with all major qc protocols and cell balancing. Holes are almost necessary. Heat output is around 10w in the worst case scenario. PETG or ABS/PC recommended. PCB reaches up to 70°C. Screws…
A useful print to hold indicating desiccant. When the desiccant changes color and has absorbed all the water has held it needs to be dried out. This typically involves laying it out on a cookie sheet and putting it in the oven for a…
Powerbank capable of charging a laptop are generally expensive, but circuits that make these PD powerbanks function are not that expensive ( around 20 USD). Thus I designed a power bank shell to host 100W PD power bank module together…
I made a model of the TPA3116 2x50W and 1x100W Audio Amplifier because there are no 3d models of this amplifier and i wanted to design a case for it before I had orderd it. NOTE: THIS MODEL IS NOT ON POINT ACCURATE! Link to buy the…
Printed on my Bambu P1S using PETG. Some filaments spool is bit tall, so I would suggest to print 83mm though 73mm can fit most.
This is a windturbine made from plastic waste. It can be made with easy to find parts and is completely open-source. With it's maximum power output of 100W, it proves that real power can be made with a much smaller carbon footprint than…
I modified the model to suit my needs - 4s1p instead of 4s2p, and also a newer revision of the board - 2 pieces of usb c, the screen in a different place Charging board link
Replacement impeller fan for Commercial Chef CCD100W. Print in ABS! Do not print this with anything less than ABS-level heat tolerance. I didn't try any other filament types. Press fit onto the motor shaft. Don't press it down all the way…
Thanks to the Underware 2.0 Customizer, I have adapted the mount for an UGREEN Nexode 100W Desktop Charger.
Designed this to add a bit of protection to the solar panels when used leaned up against something. * V2 has rounded corners which add strength.
I decided to make my portable power bank with PD using IP2368. I used 4 batteries 18650 connected in series. The battery balancing board must be attached to the battery holders. No bushings are required! You will need a few screws: 4 x…
Modular 21700 Powerbank. The cheapest branded (samsung etc.) 21700 batteries can be found on nkon.nl (I am not affiliated with them). I am using a cheap ip2368 board from aliexpress for 100w quick charging.
This light needs articulated mount to be mounted on a light stand – https://www.prusaprinters.org/prints/75428-articulated-mount-for-light-stand-bracket All of the details in a blog post –…
A very small housing for a Raspberry Pi Zero W and a powerful 2.1 amplifier (~ $37) that drives stereo speakers plus a subwoofer (2x50W plus 100W for sub) I currently run this network music player package on the Rpi: www.moodeaudio.org…
Enclosure for chiniese bought subwoofer amplifier, I have designed it to be glued together, once put together, box have no openings for wires or any type of plugs, as that can be drilled if anyone have specific needs as per that.…
This is a wall mounting bracket for the Anker 100W 4-port charging station that I have that I designed back in early 2021. Since I wanted it to be wall mounted i left the port-side open so it could be easily removed if needed. fasteners…
Kunststoffteile für eine Photovoltaik-Mast-Halterung für zwei Panele (900x670mm). Angegeben sind unten die Teile für meine Konstruktion, natürlich sind wie immer anpassungen möglich ganz nach euren bedürfnissen. Für meine Halterung werden…
Found @davidhbrown model to be a perfect fit on my bed, I went ahead and remodeled the whole thing in F360 in 1 single part. Should be almost a 1:1 replica from his FreeCAD model. The "upper_pins" might be slightly different, but should…
BOM 2x printed parts (both sides are the same), select the type according to the marking 1:1 or 1:4 1x - Ferrite BN-43-7051 with 2x three turns of twisted conductor/pair 1x - UHF Female ( SO-239 ) 4-Hole Flange Panel Mount Coaxial…
-A simple cable holder for the Ugreen Nexode 100W Power Bank (UGREEN Nexode Power Bank 12000mAh 100W) will certainly fit other models of these dimensions. - Some Anker power banks have similar / identical dimensions - power bank…
use 20mm diameter PVC pipe (electrical pipe in Europe), cut them at the right dimension for your panel and insert corners, and middle parts. use M6 screws and nuts to fix the corners and the middle parts attach a small rope to keep the…
Skadis mount for the UGreen 100w 20,000 mAh Power Bank. Includes the ability to store the provided USB cable.
This tray is a resized remix of @sblomfield trays for the Commercial Chef CCD100W6 / Westinghouse WFD100 utilizing infill meshing. It is sized to fit precisely between the stacked plastic trays which come with the dehydrator. Top and…
Super quick and dirty protective shroud for the ZK-1001UM, a mono mini amp based on the TPA3116D2 (9-24V input). I found this to be a very high value all-in-one amp, it just needed some sort of protective structure around the PCB to be…
I decided to assemble my own version of the popular 100W power bank board on Aliexpress. For this, 21700 5000 mAh batteries were used. The assembly is extremely simple, you will need to carefully insert the display without damaging it. I…
I have a thin Baseus 100W Power Bank that I want to mount into my bike's cargo basket. But it's a bit awkwardly shaped for mounting. Plus, I want to have a bit of rain protection, and hiding this expensive-looking bit of tech inside a…
I used M2 threaded inserts for the mounting of the pcb and M3 inserts for mounting of the case. Alternatively you can punch the 4 holes open und screw through the case (e.g. to screw it onto wood). I used PETG and it worked fine. PLA…
Baseus 65W/100W mount on IKEA LACK furniture, will need to use supports
https://www.instagram.com/reel/DAWUwaYuuJo/?igsh=MXJybW01eTY4d2pyaw== BOM: 4 * M3 x 10 self-tapping screw PLA, PETG or ABS filaments print with default setting of Bambulab A1 made for UGREEN 100W GaN Charger (not affiliate link)…
I had some locked Lenovo Thinkpad batteries that no longer work with a laptop, but the cells inside those batteries were in good condition. They all have roughly the same capacity after testing. So, I decided to give those cells another…
Enclosure for sub woofer Amplifier, there is slight play vertically, I am mounting mine upside down so i gave it a bit of horizontal play. Works either way, mounted right side up or upside down update. Split into top and bottom files got…
Description Desk or table mount for Baseus 100W/65W charger. The mount consists of: Charger mount Desk mount TPU pad to prevent slipping Screw pad to protect the desk Two screws, with a 5.2mm insert Screw caps Screw pads from the bottom,…
For fixing module screw - M2, for fixing panels - M2 or M3
The important points: An extension to use the 235mm (9.25 inch) CCD100W6 dehydrator for drying filament. I don't have much space, and wanted to use the smallest dehydrator I could find that still had at least 10mm of clearance around the…
I built my own 100 W power bank around the popular MYZL-YD24-V2.32 board ("100W 5S Flash Charge Mobile Power Circuit Board") and designed this case for it. The case is only 97 × 23 mm in footprint: five 18650 cells stand side by side in a…
This is the Flashlight module for my Modular Power Block, This can be combined with all the large current modules of the MPB. For the base unit this model gets attached to, see here . The battery life can be several hours, depending on…
Ugreen 100W 4 port power brick sucket support https://cad.onshape.com/documents/ef6935319325c4aa4372ca06/w/cf0829c898deaa24be5da600/e/dffeccbcd64b1b85687af1f4
DBrand Killswitch Mount for Baseus 100W Portable Charger Easily mount your Baseus 100W portable charger to your Steam Deck using the Killswitch case. I wanted to make sure the screen was visible while in use so you can see how much…
Gedruckt in PLA Für Makita Akku Adapter: Makita Battery Mount by GPlatek on Thingiverse: https://www.thingiverse.com/thing:352094 AkkuTerminal: https://www.ebay.de/itm/386728240720 Module: Voltmeter: https://www.ebay.de/itm/135144196030…
This power bank is very easy to assemble and not so expensive). I ordered the power bank board and the BMS board on ALI. They cost me 11.3 dollars. The batteries are used from a scooter with a final capacity of 2500 mAh. You can use only…
Read the originals' description for assembly and electronics instructions. This was made so that I can print it on a smaller 3D printer such as the Weedo Tina 2.
This is made to fit on the bottom tray of a Commercial Chef (Westinghouse WFD100W) Filament Dryer/ Food Dehydrator. Nine ¼" inch Ball Bearings roll inside a track allowing the spool resting above it to spin effortlessly. (honestly, it…
Perfect pot for plants. prevents overwatering and aerates the roots. improves root development.
It is a housing for the BREWA 100W 230V/230V isolation transformer. LEDs, fuses, switch and socket are built in from the front. Power socket on the left. I also prepared ventilation holes (they are not calculated whether the hole is…
Lien vers notre vidéo d'explications et de montage : https://lfp.yt/yt100wcob Bonjour à tous, Nous sommes heureux et fiers de vous présenter notre projet 100% fait maison. Il s'agit d'un projecteur LED COB de 100W alimenté par une…
Retaining clips that snap onto the Commercial Chef food dehydrator. The unit is 240cm in diameter which is almost the exact same size as the Rubbermaid Commercial Products round storage container which I got on Amazon for less than $8.…
Simple holder to attach the UGREEN charger to the wall with 2 screws.
Why did i build it ? I needed a powerful, portable lab power supply with modern USB-C capabilities. Long story short, looking at the market, there just weren't any good options that combined heavy-duty variable DC output with modern Power…
Topsolar 100W Solar Panel Holder Print Settings Printer Brand: Creality Printer: Ender-5 Plus Rafts: No Supports: No
You can print it with the text facing upwards for better quality (use brim if u have poor bed adhesion) or flat on its belly if u don't care about the text quality. I recommend taping it down with double sided tape . Happy printing !!
slide on tray for charging brick. We use it for adapters to older USB standards.
It's been unreasonably cold here in Florida lately, so for the first time, I've had some warping issues printing ASA (my primary filament). Anyways, I also wanted to get slightly higher chamber temps. I had used a single 100w heater in a…
W(58mm), H(3.6mm), L(0-125mm) if you have lipo's that are larger or smaller it shouldn't be to hard to edit the model in the cad i modeled the batteries height at 3.61mm putting a strip of foam tape and the rear of the batteries during…
The plastic broke in the trigger, I had to replace it… I printed it with: ASA (I don't know how much heat need it to endure) 0.2 layer height 0.4 nozzle 3 perimeters 10% infill 4 top and bottom layers no support pins should be printed…
I upgraded the PSU with an additional boost converter to support higher voltages. Now the PSU is variable from 0-50V @100W instead of the previous max. 0-20V the USB-C PD standard supports. Changes: The connection plug needed to be moved…
I've dropped our Bosch MK3501M food processor which broke the gear/coupler on the base of the machine so designed a new one. I've printed it with PETG with 100% infill but haven't tested the durability of the part yet. I can imagine that…
Needing extra power for a Blackmagic Cinema Camera, I found a USB-PD cable that give the 12V output required. I knew the Charmast powerbank (https://www.amazon.co.uk/Charmast-23800mAh-Delivery-Portable-Compatible/dp/B08ML1PHB2) supplied…
This is a Cap for your Ugreen 100W CD254 Charger. It helps to Protect the plug part.
Having started to have a good sort out of my office, i decided to start to use storage systems such as gridfinity and multiboard to organise all my stuff. I am in the process of sorting out draws and colour coding them with handles and…
This is a case for an USBC PD 100W Buck Boost Charger. It gets hot and need to be cooled so a fan is included. The fan is connected to +5V "A+C OUT" and GND to a Ground pad of the USB-A connector (see pictures)…
High difficulty Gonna need good electronics knowledge as no instructions. Need an assortment of m3 bolts and nuts The chinese 100w led is pretty inefficient, produces a lot of heat, even so i think the fan and heatsink i chose were…
I needed a bracket to attach a PSU under my desk to power some led strips, so I made these models: Bracket for a 100W PSU, it supports units with these dimensions: 199*98*42 mm Bracket for a 50W PSU, it supports units with these…
A quickly done (but useful) wall mount you can stick to any flat wall and keep your hair dryer (Philips - ThermoProtect 2100W) up.
Remix base to mount the Mean Well 24V 100W as a second power supply for Ender3 style printers. M4 bolts and M4 T-Nuts are used to mount the printed base to the aluminum extrusions. M3 bolts are used to attach the power supply to the…
I've printed the holder upright, with tree-support for the hooks. The hooks fit snug in the Skadis-board. The dimensions of the charger to fit in the holder are (length x width): 39mm x 44,5mm. The height shouldn't matter. Anker Part#:…
I needed a power bank holder for my Insta360 Luna Ultra and Tripod so I could do extended 4k30FPS recordings. I'm sure someone could remix it to make it better collapsible for storage, but for my purposes it works great. Recommending…
Dell 100W GaN Slim charger holder for vertical or horizontal mount. No support needed. Power adapter Info Do you like my models? Consider buying me a coffee .
Disclaimer: This is still a work in progress! The files might be updated without further notice.. The Burley Coho XC trailer has been upgraded in two steps: 1: Attaching a battery & electric motor (…
After a week where I laser cut for hours a day, my throat was hurting despite having an extractor system. I designed these to reduce smoke from the front intake vents as well as reduce the risk of reflected beams coming out of the front…
