Liczymy pasujące modele…
Yeelight Pro is a great addition to the workplace with a computer. It can illuminate the area with keyboard in front of the monitor and behind the monitor. It is installed by hooking it behind the top edge of the monitor. The heavy metal…
Webcam Step: Elevate Your View Modern technology has gifted us with sleek, thin-framed monitors. While these technological marvels enhance our workspaces, they also present a new set of first-world problems: webcams dangling into the…
Have you ever had an issue with RGB strips falling off the back of your TV? Well, so have I. I was also very unhappy with how it bounced off the back of the wall and the lack of even glow around the TV. So, rather than spend an extra…
I find the standard Tobii Eye Tracker under-monitor flex mount unattractive and insecure. I designed this mount to cleanly and securely affix the eye tracker to the front bezel of a flat or curved monitor. Features Fits Tobii Eye Tracker…
I designed this simple monitor mount to use for a 24 inch 100x100mm compatible monitor. Material needed: This mount needs 27-28mm wooden roundstock found in hardware stores. Cut to length to determine the height of the monitor. Keep in…
This was designed to be printed without supports, although I would say it's right at the limit of what a FDM printer with a 0.4mm nozzle can do both in size and overhangs. It would probably work very well for resin printing, but I haven't…
This is a tool to correct the angle for a triple monitors setup for sim racing
Here is a set of four arms you can adjust in various positions depending on monitor size and port placement. For the most stability try attaching the bottom arms first using both VESA mounting holes. Then adjust the top arms once the…
This print will allow you to use your Dell SE2419HR monitor with a VESA mount based monitor stand. This will be compatible with any Dell montor that uses the same metal pivot on the stand. To use: Detach base from existing monitor stand -…
It annoyed me that every time I bumped the desk my dual monitors would shift out of alignment. So I decided to make some clips to hold them together. Ended up being far more time-consuming that I expected. (Why don't they make these…
Developed this sim racing canopy, as I wanted something that had a high quality OEM-like finish with zero flex. Consists of a number of brackets angled at 45degrees for the centre, and 38 degrees for the side. Instructions: You will need…
An adjustable shelf that sits on top of your monitor to put your favorite Lego mini figs on display. Fits on my curved and flat monitors and looks great. Need to print the Shelf and Support Arm. Support Arm can is adjusted to fit your…
A stand for two external monitors (brand Arzopa). There are two versions of the upper parts: straight and tilted. The tilted one is 10 degrees tilted. The extra holders can be used, but it's not necessary. Link to the post .
I have a cheap AOC monitor that uses a pillar into the stand to hold itself up, and has no VESA mounts. I am not wanting to replace it just yet so this is a solution to that problem. You will want to have good layer adhesion to print it…
This Spacer/Riser will allow you to put your webcam higher on your monitor, to prevent overlapping into the display area if your monitor has a thin bezel. It is designed to hold a Logitech C270 15mm higher on a Monitor that is 30.5mm…
Made to fit an iPhone 14 Pro or smaller. Most curved monitors should work, this was designed for a curve of 1500R but it has some wiggle room built in. Print with the flat side down, supports are optional - if your printer can't handle…
Just a simple 3D Printed mount for my Kinect V2 so i can make Video Calls with a High Quality as well as 3D Scans in front of my Table :) Support Structures are not needed if you print slowly enough with good Bridging Settings. My Model…
Seemed mad to be using a protractor to align my triple monitors with a 3D printer available! Created a simple template to help align the three monitors on my sim racing rig to 45 degrees or 60 degrees. Should work with any size of monitor…
Attach Your Microphone next to your Webcam for better quality audio during streaming, videocalls, etc... Needed: 1x M6 screw 40 mm 1x M6 nut (wing nut or use 3D printed knob)
The original is from 3DDIY . This model is for a wooden panel which is 200mm wide and 18mm high. The exact dimensions of the model can be found in the attached drawing.
I wanted to place some stuff on top of my 49-inch curved Samsung monitor, so i created this shelf. It will work with all curved monitors with a display radius of 1800mm (1800R) which have the horizontal slot on the back 54mm below the top…
iLoud Micro Monitors speaker stands with cut-outs for rubber mounts in both normal and elevated positions. The columns can be resized for height adjustment. ATTENTION: the columns must be printed with a horizontal expansion (in Cura) of…
I wanted a holder for the Vesa mount on the back of my 27 inch Dell monitor - there are a couple on printables but I didn't want to print for 30 hours and then find out I don't like it - so I designed my own. I printed it in PLA with 10%…
Vesa Mount adapter is designed for the Dell S2340Lc Monitors, but is also compatible with other S-Series Monitors
I recently bought a pair of Superlux HD381s for in-ear monitoring. They are great in-ears, and the price was very keen. The only problem is they came in a disposable plastic bag, in a cardboard box. This wee box has a spindle on the lid…
Case for KZ ZS10 in-ear monitors. The KZ ZS10 in-ear monitors are well-known among audio enthusiasts. I have been using them for many years. There is a wired version and a switchable Bluetooth module. This case also withstands long wires.…
The main idea is to ensure that the monitor's casing does not touch the plastic stand across its entire surface, preventing unwanted parasitic noises and vibrations. This model features TPU legs that separate the monitors from the desk…
Ein einfacher Halter für tragbare Monitore. Die mitgelieferte Hülle, welche auch als Ständer verwendet werden kann, war mir für die Nutzung zu Hause zu wackelig. Erstellt für einen YODOIT PTM15 Monitor mit 15,6". Passt aber sicherlich…
No supports needed Printed with PLA 0.2 Layer Height 3 Wall loops 15% infill Gyroid
A Simple IEM holder for AOC 24G2 and 27G2 (it works for the G2S models too) you just need to use double side tape and fix it into one of the top corners of your monitor and its good to go. (Forgive the printing quality of the image, i…
This mount is intended for use on Walmart's onn. brand of budget monitors , which have a distinct curve to them that makes regular sensor bar mounts impractical. I intended it to be used with Mayflash's Dolphin Bar , although it should…
Habe diesen Fuß für das Regalbrett KONSTRUERA von IKEA (B x T - 57 cm x 28 cm) entworfen, um meinen Monitor höher zu stellen und meine Tastatur darunter verstauen zu können. Befestigt habe ich die Füße jeweils mit 3 Schnellbauschrauben…
There is a screw hole below the bracket for locking bottom grips. You can add the additional part for locking the monitor. This Bracket's dimensions are for ASUS MG278Q Monitor mount. With this bracket, this mount can use on any 27"…
PETG PRUSAMENT 20% INFILL SUPPORTS WHAT YOU NEED : EIZO MONITOR WITH stand FlexStand 4/FlexStand 5 PCSK-03 TERMINAL HOLDER MAC MINI CABLES M4X45 DIN 912 4X M4X10 DIN 912 4X BN 1936 press-in threaded insert M4 4X FELT PADS 4X OPTIONAL…
Headphone holder for mounting on Samsung S24D300 or SA300 monitors, etc.
Mount your Boya microphone to your Samsung monitor using the monitor stand screws Snap fit Fits Samsung JG56 monitors: LC27JG56 LC32JG56 or any monitor with the same monitor stand fitment. If you use this then you need to use the VESA…
Adapter / Holder for Tobii eyeX to attach to curved monitor. It is designed for monitors with a 1800R curve and a bottom bezel that is 15mm thick. Press 6x2mm magnets into the 4 front holes (check polarity with your eyeX!), secure with…
My pair of monitors are mounted on a stand. I use these brackets to help keep them at a precise angle, and to keep them from warbling around. 3D Printed Monitor Bracket at patshead.com Monitor Bracket for QNIX QX2710 at github Category:…
Assembly: just slide the feet onto the plate and you are done If you want a larger table use the double foot to connect two plates it will also help to keeping it stable. The top of the plate can be fitted with a logo as shown (be careful…
It's just my idea to cover my new active speakers which many many DJ's are using all around the world. 4mm holes need to be drilled on the speakers, so the grills to be placed and glued. Or maybe you can make your own style to place them.…
I designed this stand specifically for studio headphones, which often have wide, heavily padded, and heavy headbands. Unlike generic "gamer" headphone stands, this model features a deeper support surface to accommodate extra padding and…
If you have an arm-mounted LG-monitor, you can now use the monitor foot mount to give you Steam Deck a decidated, floating spot on your desk. Check picture 2 for the required mount on the back of your display. Printed with 15% infill, 2…
This is a mount for two Philips Hue lamps. The lamps can thus be mounted on the base of an AOC gaming-monitor. 2x Philips Hue Ambiance Play Lightbar 4x grub screw m3x20 --- or --- 4x normal screw m3x30 My AOC Monitor: AOC CQ27G2U/BK (the…
The model allow mounting a lightbar or a webcam on OLED monitors with 5 mm thick screens, with a curvature of 1800R. Printed in PLA, no special features needed.
DE: Mit diesen 3D-gedruckten Füßen lässt sich das IKEA LACK Wandregal (110 cm Variante) ganz einfach in einen stilvollen und funktionalen Monitorständer verwandeln. Das Regalbrett bildet dabei die obere Ablagefläche, während die Füße für…
Magnetic head mount for use with the Multifunction Arm mounting system: I attached mine to my variation of the Hinge below that doesn't Spin (which is no longer necessary with a magnetic mount and may be required if the plate on the…
Speaker stands for the 3.5" PreSonos monitors.
Yamaha makes an official mounting kit (part no SPAT1) but it's not available for purchase in my country so I made this to mount the speakers of an MS100DR to the electric drum kit frame. Printed in PLA. Fits 4 x 16mm m5 bolts with hex nuts.
Simple slide on mount for a Belkin Universal Media Reader on the new iMacs or new thunderbolt or LED monitor. Instructions Slide the reader in and plug in the USB. Simple Category: Computer
This Laptop holder can hold Laptops like my work laptop which is a Lenovo P16 Gen2 (workstation Laptop which is quite thick and heavy). The gap for putting in the Laptop is 30 mm wide, which is enough only for the P16 in case it is…
In slicer you can change dimention 8 square tube connector corners Print this with support 4 parts 6 cm , this i can print on my printer , vertikaal , by me 105 % and brim 10 x 10 x 60 outside must be 8.1 x 8.1 inside 4 parts 30 cm…
Da der Platz auf dem Schreibtisch immer weniger wird, wollte ich die Boxen hinter dem Bildschirm verstecken. Das Teil kann aber auch als Ablage unter dem Bildschirm verwendet werden.
An adapter to put in place on the hinge to prevent it from tipping over when mounting a monitor, such as a 49" ultrawide, which is heavier than the specs allow for. You can still tilt the screen left and right, but not up and down. I've…
I was trying to replace my Dell Soundbar AC511 with a pair of better speaker units. To mount the new speaker units (which have two readily available screw holes per unit), I reverse engineered the mount units of AC511, and created this…
Compact 4" coaxial 3D printed active studio monitors with DSP (only digital input, dsp/amp board limitation). Monitors are sealed design for best transient speed and mid-range monitoring with target Qtc 0.50 (Critically Damped) and…
I extended the length of the cold shoe further back to help with my shotgun style mic.
I did not want to pay between 2 and 3 hundred dollars on the manufacturer monitor stand to add multiple monitors to my sim rig. I designed these to use 2x4's to create a cross brace to mount monitor arms. I did not even end up screwing…
Wenn du mehr Platz unter dem Monitor brauchst. Oder er einfach nicht auf der richtigen Sichthöhe steht.
Longer stand for bigger monitors designed to fit the original files exactly as the shorter one did
I needed a mount to attach a thin client to the back of the monitor. HP EliteDisplay E272q
Under desk mount to hold KVM Switch, for the KC-SHM1 Switch provided with the "Displayport KVM Switch 2 PC 2 Monitors 8K@30Hz 4K@144Hz, Dual Monitor KVM Switch". 2x M1.4 screws recommended to affix back plate, but can be held in via…
I use a remix of https://www.printables.com/model/123617-100x100mm-vesamount-for-monitors for my monitors, but my monitors have an external power brick (about 75x65x30) that I wanted to keep up and away from other heat-generating objects…
These are 3D printed parts for mounting a Raspberry Pi, field control hardware, and other accessories to the back of VEX Robotics Competition field monitors. The 3D printed parts are attached to the monitor with strong double-sided tape…
I overengineered this support plate so it fits my Dell U3225QE monitor like a glove, and securely supports and centers my Logitech MX Brio 4K webcam. It may also fit other Logitech webcams, and other modern Dell 4K monitors. I also own a…
Slide it shut when you're not on a call. A thin sliding shutter that prints already inside its frame: stick the frame over a laptop or monitor camera with a strip of thin double-sided tape and slide to open or close. Six on a plate.…
Velcro Strap Secure Plate for Monitors on Gravity SP3202 Stand This plate is placed under the original Gravity plate and supports up to a 54 mm wide strip . To fix the plates together: 4 × M4 Nuts 4 × M4 Flat Head Screws (M4 × 16 mm or…
The Pareto Speaker is a DIY desktop monitor that combines custom 3D-printed acoustic geometry with off-the-shelf plumbing hardware. Utilizing a standard Geberit 87.5° T-Junction pipe as the main enclosure, this design features a custom…
This two-part slide-on mounting system allows you to mount an HP EliteDesk Mini PC directly onto the vertical column of an HP EliteDisplay monitor stand without taking up desk space. simply slide the brackets down over the monitor post…
Adapter to stack two Dell P2319H monitors on their original stand. Might fit more modells. The adapter allows for a bit of height adjustability on both monitors but i do not recommend raising the top monitor from its lowest position.…
Yamaha makes an official mounting kit (part no SPAT1) but it's not available for purchase in my country so I made this to mount the speakers of an MS100DR to the electric drum kit frame. Printed in PLA. Fits 4 x 16mm m5 bolts with hex nuts.
The model allow mounting a lightbar or a webcam on OLED monitors with 5 mm thick screens, with a curvature of 1800R. Printed in PLA, no special features needed.
Compact 4" coaxial 3D printed active studio monitors with DSP (only digital input, dsp/amp board limitation). Monitors are sealed design for best transient speed and mid-range monitoring with target Qtc 0.50 (Critically Damped) and…
Under desk mount to hold KVM Switch, for the KC-SHM1 Switch provided with the "Displayport KVM Switch 2 PC 2 Monitors 8K@30Hz 4K@144Hz, Dual Monitor KVM Switch". 2x M1.4 screws recommended to affix back plate, but can be held in via…
Should be able to handle bigger and heavier monitors too. Instead of printing the rod yourself, you can also use a 15mm wooden rod. However, you won't be able to fit it into the foot's clip since the printed version has a flattened side.…
Full description This wearable gait tracker is built around an ESP32 controller paired with a 6-axis IMU to capture motion and orientation data in real time. Designed as a lightweight leg-mounted device, it integrates a 450mAh…
I extracted the desk and its items from a ripped Lethal Company Unity project, and used the 14 model setup from my GeneralImprovements mod. I included STLs for both vanilla monitors (2 large, 8 small), and modded monitors (3 large, 12…
My work requires the use of three monitors. Due to company restrictions on the hardware I can use, I've purchased 2 portable external monitors and have these attached to my laptop. Unfortunately, these extra monitors take up a significant…
Should be able to handle bigger and heavier monitors too. Instead of printing the rod yourself, you can also use a 15mm wooden rod. However, you won't be able to fit it into the foot's clip since the printed version has a flattened side.…
Full description This wearable gait tracker is built around an ESP32 controller paired with a 6-axis IMU to capture motion and orientation data in real time. Designed as a lightweight leg-mounted device, it integrates a 450mAh…
For those struggling with the Tobii mount, which keeps coming loose. This is a universal mount for all monitors.
After couple of tests I was able to create a fully printable adjustable holder. All parts can be printed and put together. I suggest to print all flat with support because is faster and brim if necessary (not sticking on plate). If you…
This part is for a Ugreen Hdmi 2 PC kvm: https://www.amazon.de/dp/B0FXX2LDV6 This part is mirrored — print 2 (one of each side). Designed for the Multiconnect system. Print Settings: Material: PLA / PETG Layer height: 0.2 mm Supports: None
Micro Monitors V1 — Full Component & Hardware Bill of Materials Test video: https://www.reddit.com/r/diyaudio/s/QxL9G90VEA Printed mine with 25% infill, 3wall loops and top/bottom layers and support where needed, mid pods was printed face…
I overengineered this spacer so it fits my Dell U3225QE monitor like a glove, and securely centers my Logitech C930E webcam. It also fits other Logitech webcams such as the C920, and other modern Dell 4K monitors. I also own a Dell…
I overengineered this spacer so it fits my Dell U3225QE monitor like a glove, and securely centers my Logitech C930E webcam. It also fits other Logitech webcams such as the C920, and other modern Dell 4K monitors. I also own a Dell…
I bought Some Dell monitors and used them for some time. Eventually I got a mount, so I could have a 4 monitor setup. These didn't have VESA mounts, so I was looking at replacing all my monitors. I decided to model an adapter to fit on my…
I bought Some Dell monitors and used them for some time. Eventually I got a mount, so I could have a 4 monitor setup. These didn't have VESA mounts, so I was looking at replacing all my monitors. I decided to model an adapter to fit on my…
This design is made to be seen at a distance. To help identify which computer a person is sitting at for assistance. For single-sided printing, just change the color at the proper layer-height. With an MMU you can do double-sided printing…
With a pair of 27" 4k Dell monitors, my logitech C920 camera was really high and at an odd angle when resting on top. I printed https://www.printables.com/model/2679-monitor-side-mount-for-webcam/files and it was great but getting it to…
I've designed a very simple headset holder to put in the back of your monitor screen. It was designed for a 15mm max thickness, but feel free to remix the model or modify it to adapt to your monitor. Printing sideways is recommended
as I mentioned in the summary, I love everything about the original design except the dowel hole on the clamp + foot models is a slightly awkward size to fit a standard imperial-size dowel, so I added about 0.2mm to the radius of each of…
My monitor is a gigabyte M34WQ curve monitor. I used 3M double-sided tape to stick on the back of my monitor.
Raise webcam that obscures small part of the screen
I designed this glasses holder for monitors with a 1mm bezel. I use an ASUS ProArt Display PA279CV 27" for my office work and have two sets of glasses - one for regular use and one for computer use. I always forget to switch to computer…
Filament Compatibility: Any type of filament can be used, offering flexibility based on your preferences or what you have on hand. Layer Height: Set your 3D printer to a layer height of 0.2mm for an optimal balance between print speed and…
I'm a happy owner of SimLab Vario triple monitor stand build from 8040 profiles. There is a one thing I don't like about it though: side rails are kept in place only by pivot screws which won't provide any rigidity when you happen to push…
GOW + Skillup template for ROG monitors with Light in motion. Category: DIY
GOW logo for Asus monitors with light in motion base Category: DIY
![Stand for two external portable monitors [Stojan na dva externí monitory]](https://media.printables.com/media/prints/425235/images/3517722_aa61c70b-8f0d-4d31-91d5-0d99a8df5354/49_19.jpg)
