1475 modeli
Simple stand originally designed for a Ubiquiti UniFi AP AC Pro Also confirmed to work with: UniFi Access Point WiFi 6 Pro U6-LR-US Possibly others? If it works on other models drop a comment and let me know! Snap fits into existing holes…
Wydruk około 2,45 €–3,00 € nettoWstępna wycena jednego wariantu
UPDATE 20.1.2024 - added versions - AP: LR / Pro / Nano / Lite Complete stand + mounting bracket for Ubiquiti Unifi AP. The model is All in one, so it can be printed as one piece without need for screws. You just click it on. In the 3mf…
Wydruk około 1,63 €–1,99 € nettoWstępna wycena jednego wariantu
Mounting bracket. Recommended to print with a 0.4 nozzle with a layer height of 0.2 or less! For material, something that's more resistant to heat than PLA is advised. Commenter @jornthree_2921709 recommends PETG or ASA. I've used a PLA…
Wydruk około 0,81 €–1,00 € nettoWstępna wycena jednego wariantu
This is a reupload from https://www.thingiverse.com/thing:5572539 which is itself a reupload from a different website. Credit to thatguy_ie on Thingiverse and Crosstalk Solutions on youtube for bringing it to my attention originally.…
Wydruk około 3,13 €–3,82 € nettoWstępna wycena jednego wariantu
I required a movable access point and decided to create my own desk stand for an Ubiquiti Unifi nanoHD access point. Recomended Material : PLA Nozzle Diameter : 0.4mm Layer Height : 0.2mm Support : NO In-fill Percentage : 20% Required:…
Wydruk około 4,16 €–5,08 € nettoWstępna wycena jednego wariantu
Das ist ein Case für die Montage einer Ubiquiti UniFi IN-WALL - UAP-AC-IW Damit kann die UAP-AC-IW einfach an die Wand geschraubt werden und das Netzwerk Kabel nach unten herausgelegt werden. Habe für die Montage wieder M3 Gewindeeinsatz…
Wydruk około 5,40 €–6,60 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A stand for an Accesspoint 6 pro from unifi. The lan cable can be routed through the bracket. The aim was to place the AC point on a high shelf. It is printed in 2 parts and glued together with a sleeve.
Wydruk około 12,39 €–15,15 € nettoWstępna wycena jednego wariantu
Spacer that allows me to mount my UniFi switch on a full width rack. Print instructions Printed using Slic3r defaults for .2mm Generic PLA.
Wydruk około 2,71 €–3,31 € nettoWstępna wycena jednego wariantu
This is wall mount for all Ubiquiti UniFi AP, Lite, Pro and Long range. (for big mounting plate with 3 or 4 screws and small mounting plate) this mount fits to newer APs with blue light. There is wall mount and corner mount version.…
Wydruk około 3,65 €–4,46 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I was looking for a decent G3 instant corner mount that allowed me to hide the power cable. I really liked the design of Tadufeu but it lacked the feature to hide my cables so I created a remix for this purpose. Don't mind the finish off…
Wydruk około 0,11 €–0,14 € nettoWstępna wycena jednego wariantu
I wanted the cables to be neatly tucked under the switch, so I created this stand.
Wydruk około 17,97 €–21,97 € nettoWstępna wycena jednego wariantu
Mount aligns with OEM screw holes in UVC-G3-Flex-PWM-WT mounting kit for Ubiquiti Unifi Protect UVC G3 Flex security camera. Hinge is indexed with detents allowing for secure positioning of camera angle at 30-degree increments. Hinge is…
Wydruk około 1,22 €–1,49 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A mount for the Unifi Switch 8 (US-8 and US-8-60W). The size of the switches this mount is designed for is: 150x100x30mm.
Wydruk około 2,12 €–2,59 € nettoWstępna wycena jednego wariantu
OnShape model: https://cad.onshape.com/documents/e575f295105d8e9e32a6bc56/w/313938088c26a895e167df17/e/4262aab72ff56fb5d56f9058
Wydruk około 2,76 €–3,37 € nettoWstępna wycena dla PETGMateriał u źródła: PET
If you want to put your Unifi Bullet G5 on a table or shelf instead of a wall, this is for you. The print is technically two files, the cone stand model provided here, combined with the ring with the provided elsewhere mount. This is just…
Wydruk około 2,91 €–3,56 € nettoWstępna wycena jednego wariantu
A Unifi Switch 8 rack mount for a 19" rack. Printed with No supports 3 perimeters / walls Use the “Blende Links.stl” panel from 19" Rack Panel Hexagon Design to get the other half of the mounting panel.
Wydruk około 2,87 €–3,51 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Every piece of hardware needed to attend Eden Academy. EdenAcademyDressAccents x 7 – There are four on the front of the dress, one on each sleeve, and one on the centerline of the back. There is a slot for a 5 mm ribbon to be sewn through…
Wydruk około 0,27 €–0,33 € nettoWstępna wycena jednego wariantu
A holder for a Unifi Enterprise Access Point. Print settings: You need to add modifiers around the hooks. I added spherical modifiers with 100% infill. All other infills are at 15% supports needed The 3mf file should already include the…
Wydruk około 2,23 €–2,73 € nettoWstępna wycena jednego wariantu
Unifi G3 flex wallmount adapter to use insulation dubel. you can use Fischer 50mm insulation dubel, or any other eqvivalent with utp cable fixing use standard ziptie
Wydruk około 0,81 €–1,00 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Wall mount for Unifi U6 LR WiFi access point.
Wydruk około 3,38 €–4,13 € nettoWstępna wycena jednego wariantu
None of the existing wedges for the G4 doorbell fit my needs, so i made one that did. This wedge puts the doorbell at 90 degrees to the door for doorbells that are mounted perpendicular to the door. I didn't trust the snap-on mounting to…
Wydruk około 5,22 €–6,38 € nettoWstępna wycena jednego wariantu
This is a battery bracket for RAK Unify 150x100x45 enclosure plate . It allows you to fit 3 cell 18650 battery packs like the Adafruit 6600mAh 18650 pack . Print settings I used on my MK4 with 0.4mm nozzle: Print in PETG or ASA if using…
Wydruk około 1,13 €–1,38 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Wedge Mount for the Unifi Doorbell Lite to optimize the angle, as an alternative for the original wedge of 20°. Details Optimized for easy printing and strength STLs provided for 15°, 20°, 25°, 30°, 35°, 40° & 45° Configurable F360 file…
Wydruk około 1,05 €–1,28 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is v3 of the model, Ultimate Edition. EVEN more ventilation ability but supports are required . Elevates UTR device by 3 mm to improve passive airflow and reduce heat build-up Ventilated underside design promotes air circulation…
Wydruk około 0,47 €–0,57 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Consists of Mount and Ring . Only the Ring is visible once installed. Both pieces press fit onto the Chime, holding it in place and holding the Ring to it, covering the hole. The goal is to not have to cut a huge hole in the brick wall.…
Wydruk około 0,89 €–1,08 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Printable bracket for mounting a US-8-150W in a 19" rack. FYI, some would consider my print settings excessive. No supports are required, but I print with them anyway… Filament: PETG Walls: 4 Infill: 40% Top/Bottom Solid Layers: 5 202609…
Wydruk około 4,87 €–5,95 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Ubiquiti AP U6 Lite ceiling mounting without drilling into the ceiling was the challenge I solved with this model. Deutsch: Ubiquiti AP U6 Lite Deckenmontage ohne in die Decke zu bohren war die Herausforderung, die ich mit diesem Modell…
Wydruk około 1,98 €–2,41 € nettoWstępna wycena jednego wariantu
v3 now released , get it here . It has even more ventilation but needs supports when printing. v3.1 also released for those of you who have a UGreen Nexode PB763/PB761 10000mah powerbank (as per one in the photos), get that custom one…
Wydruk około 0,47 €–0,58 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This remix adapts the original caddy from the HP series servers it was designed for to a Hitachi HUS (Hitachi Unified Storage) SFF 24 bay drive chassis. The drive bays are deeper than typical Dell or HP servers and hard to source (200mm).…
Wydruk około 1,66 €–2,03 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is v3.1 of the model, the UGreen Nexode Batterybank Edition. Superior ventilation ability but supports are required . Elevates UTR device by 3 mm to improve passive airflow and reduce heat build-up Ventilated underside design…
Wydruk około 0,85 €–1,04 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Table Stand for UniFi Access G2/G3 Readers: Finally a way to have a tabletop reader for adding cards to UniFi access. No more readers strewn across your desk. The Idea: Make a table-top stand, based around the existing aluminium bracket.…
Wydruk około 4,24 €–5,18 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A plaque and pin of the U.N.I.T. emblem from Doctor Who. (UNified Intelligence Taskforce). I've included the colour change .gcode from Prusa Slicer.
Wydruk około 2,21 €–2,70 € nettoWstępna wycena jednego wariantu
UK Faceplate mount for UniFi Access G2 and G3 Readers: Ah, Ubiquiti… My favourite tech company. Almost perfect in every way, except for international compatibility with mounting options. We've started using UniFi Access recently, and…
Wydruk około 0,88 €–1,08 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Yet another solder reel holder! This one however, is what I normally use at work as an Electro-Mech assembler. What I found so frustrating was that just having a solder reel on its own meant pulling the wire vertically from the reel,…
Wydruk około 0,99 €–1,21 € nettoWstępna wycena dla PETGMateriał u źródła: PET
My Unify US-8-150W didnt't fit my 10" Serverrack, so i designed my owm model for it with the PSU beeing externally placed and connected with an TX60 plug. For the heatsink i used 25x25x5mm heatsinks to keep the parts cool.…
Wydruk około 4,54 €–5,54 € nettoWstępna wycena jednego wariantu
About I'm calling this the RAKshare. A bracket for the RAK Unify 180x130x60mm enclosure to mount: RAK 1W booster 19007 / 3401 / 13302 board. Waveshare Solar Power Manager (D). Adafruit INA3221 STEMMA QT board for power monitoring.…
Wydruk około 2,48 €–3,03 € nettoWstępna wycena dla PETGMateriał u źródła: PET
v3 now released , get it here . It has even more ventilation but needs supports when printing. v3.1 also released for those of you who have a UGreen Nexode PB763/PB761 10000mah powerbank (as per one in the photos), get that custom one…
Wydruk około 0,46 €–0,57 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This coaster is designed to catch any stray grounds that fall from your coffee grinder, keeping your countertop neat and easy to clean. It includes seven holes for attaching standard furniture bumpers (9mm - example ) or slip-resistant…
Wydruk około 4,25 €–5,19 € nettoWstępna wycena jednego wariantu
Important: This fits only the GbE Version, also called: USW-Flex-Mini This is a simplified version of the unifi usw flex wallmount. It is simplfified for easier printing. Print on the flat side! (mounting holes touching the print plate)…
This version is for UniFi AP AC Pro model, other models may not be suitable. Print it to replace broken bases with PETG or ABS for rigidity, PLA is also recommended ,i added file without holes so it can be edited to your liking Update…
This is a reinforced version of UDM mount by Revnull. Who's desighn while elagent and well desighned is lacking structulary. So to prevent a repeat of the brackets snapping i have redisghned it to have quater circle reinforcemnets up each…
A modular, 2-part, 19-inch rack mount for the Ubiquiti Unifi UCG-Fiber cloud gateway. This mount is part of a 19-inch modular rack mount system I designed. You can mix and match the modules with other mounts. Take a look at my models here…
An unofficial 10-inch rack mount for the Ubiquiti Unifi UCG-Ultra | UCG-Max | UXG-Max. This model is part of a series of 10-inch rack mounts I've designed. You can check out the others here . Updates 26 Nov 2024: The V2 of this rack mount…
Desk Stand for the Unifi U7 Pro Wall from Ubiquiti. It's similar to the aluminum premium desk stand that Ubiquiti sells, but of course, like all its offerings, it's always out of stock. I created this because I wasn't sure if I wanted to…
An unofficial wall/table mount for the Ubiquiti Unifi USW-Flex-Mini 2.5G 5. It can be either screwed in place with two M3 screws or attached with double-sided tape. I have included Three versions of this model. Open mount: Uses less…
An unofficial wall arm mount for the Ubiquiti Unifi U6 Enterprise, U6 Pro, U7 Pro Max and U7 Pro. The holes on the arm align themselves with the holes marked with “A” in the metal face plate “U-PRO-MP”. I've also shared the .step file if…
A 10-inch rack mount for the Ubiquiti Unifi USW-Lite-8 PoE. To install your switch to this mount, simply slide it in. But once you reach the rubber feet on the bottom, press the a little so they can compress and enter the mount, after…
A 10-inch rack mount for the Ubiquiti Unifi UCG-Fiber cloud gateway. This model comes in 4 variants: With front cutout for power cable routing With holes for M3 thread inserts. → UCG-Fiber 10i RM for Thread Inserts.stl With holes for…
Updated version with a stronger mount and support for U6-Lite on top of U6-Pro. Thank you for supporting me! This is another free 3D model made available for you. I love sharing my models, but designing, testing, polishing, uploading and…
Printing Print in a temperature resistant material. PLA will warp within a week. I used ASA. Hardware 3x M4x4 (short) heat set inserts 4x M4x6 screws Assembly / Installation Insert M4x4 threaded inserts Drill out the top mounting hole to…
The Cloud Gateway Max gets hot! Do not print in PLA!
Basic 19" rack mount ears for Ubiquiti Networks Unifi Pro Max 16 switch Should fit both the non PoE (USW-Pro-Max-16) and PoE (USW-Pro-Max-16-PoE (180W)) variants. Printed with generic PLA-CF, 3 walls and 50% infill on a BambuLab X1 Carbon.
Texture rolling pin for clays and epoxies. Can be used to create a pattern that's perfect for brick walls or floors. Great for miniature bases. You can run a small rod through the center to use as a handle. To avoid sticking, wet the…
A replacement for the mounting plate that came with my UniFi U6 Lite access point. Handy if you bought an AP second hand without its plate or lost it in a move. Fits (confirmed by people who printed it, thank you!) - U6 Lite - U6+ - U7…
A modular 19-inch rack mount for the Unifi UCG-Ultra, UXG-Max, and UCG-Max lineup. OBS.: The UCG-Max processor reaches 75~ 90 degrees Celsius for normal use, and the bottom can get REALLY HOT . So use filaments with higher temperature…
Inspired by jurriaanpruis' design , this is modeled to use either screws or large 3M command strips to mount your Unifi Dream Machine to the wall. It has proper ventilation on the bottom to allow your Dream Machine to breath. Includes a…
The only thing worse that the subscription model, are overpriced accessories that should have been included! I made this for myself, as I will only use it with a 2280. So, if you're are only going to use a 2280 too, have at it. Includes a…
The Unifi Access Point Lite wall mount is design to mount an Access Point WiFi 6 Lite, nanoHD, or AC Lite to the wall instead of the ceiling. Two or four M4 screws are used to screw the mounting plate to the print.
Got a new print cooling fan, new filament or just curious about your printers overhang performance? This thing is the perfect benchmark to test just that. The part comes in multiple varieties depending on your needs and how thorough you…
Perfect fit for SKÅDIS mount for Ubiquiti Unifi Cloud Gateway Ultra. Does not block any I/O. Requires 2x Skadis T-Clip System - Low Profile Flush Mount Clips No support needed Printed with PLA with default setting
Rackmount for UniFi Gateway Max (UXG-Max) . As the dimensions are identical, it will also work for the UniFi Cloud Gateway Ultra (UCG-Ultra) and the UniFi Cloud Gateway Max, but you won't see the display. Ports facing front, works for…
This is only my third 3D print. I made the adjustments using TinkerCAD. I used PETG filament and an Anycubic Kobra S1 printer.
Parametric model for mounting the Unifi G4 Doorbell Pro at odd angles, on either the left or right side of the door. Intended to be used with the metal backplate that comes included with the doorbell. Rendered a couple of versions as STL,…
Just a rescale of the OG model to fit the UP 6 pro mounting bracket holes—they lined up perfectly and secured easy with short M3 screws. + nuts.
I am using it with U6-Pro, but should also work with AP AC Pro. Instead of snap fits to attach a backplate this remix has 4mm holes so screws can be used to attach a backplate. Added also version with longer stand to fit U7-Pro AP as it…
A 10-inch rack mount for the new Ubiquiti Unifi USW-Flex-Mini 2.5G 5. To install your switch to this mount, simply slide it in. But once you reach the rubber feet on the bottom, press them a little so they can compress and enter the…
A 10-inch rack-mount adapter for the Ubiquiti Unifi USW-Ultra. I've added the .step file if anyone wants to remix the model. Do you like my models? Consider buying me a coffee ;) Print Settings Printer Brand: Anycubic Printer: Custom Mega…
Thank you for supporting me! This is another free 3D model made available for you. I love sharing my models, but designing, testing, polishing, uploading and maintaining them is a lot of work. In case you enjoy this model, please leave a…
We ordered a bunch of the Unifi USW Flex Mini switches for use around the office, but they didn't come with a wall mount...so I designed and 3D printed my own. Printed it in both Prusa PLA and PETG with .20mm layer height on my MK4 and…
Simple wall mount for the Unifi Gateway Lite (UXG Lite). You can face the ports either up or down, but not sideways. “-wide” has a wide hole pattern that has the same width as the old USG Gateway wall mount, making this wall mount a drop…
A 19-inch, 2-part, modular rack mount for the new Ubiquiti Unifi USW-Flex-Mini 2.5G 5. This mount is part of a 19-inch modular rack mount system I designed, you can mix and match the modules with other mounts. Take a look at my models…
A 10-inch rack mount for the Ubiquiti Unifi USW-Flex-Mini. I have included two versions of this mount: For two USW-Flex-Minis For a single USW-Flex-Mini To install your switch to this mount, simply slide it in. But once you reach the…
⚒ No 3D printer? No time to source components? I just opened my new e-shop where you can buy physical, ready-to-use versions of my models! Designed with passion, printed and assembled with care ⚙. 📦 Shipping across the EU: 👉 Get it at…
I really liked this design but it was for the G3 Instant Camera and I have G4 Instant camera's.. Not sure why Ubiquiti decided to change the mounts ever so slightly but because of that the G4 can't use G3 mounts. So this is a remix of the…
Remix of the Open wall mount with tabs added at the bottom to allow for vertical mounting.
A modular, 2-part, 19-inch rack mount for the Ubiquiti Unifi USW-Lite-8 PoE. This mount is part of a 19-inch modular rack mount system I designed, you can mix and match the modules with other mounts. Take a look at my models here to find…
A spacer for the Unifi G5 Turret Ultra to give some room for the cables behind it.
This is a mounting system for the Unifi G4 Instant Security camera based on an excellent design for the G3 Instant. This design uses a corner bracket or flat mount with a dovetail socket, a 2 piece hinge that slots into the dovetail, and…
As I didn't want to mount the access point (UniFi AP-AC-LR) to the wall or ceiling, I have created a stand for it. 4 x M4 screws are required to mount the stand to the access point. No nuts are required.
Works great with my other panels :)
A 10" 1U rackmount for the UCG-Ultra with three keystone slots.
Hello Everyone I designed two types of stands for Ubiquiti UniFi U6+ (U6-PLUS) Access Point. The stand is compatible with other UniFi AP models that have a dimension of Ø160 x 33 mm (U6-Lite, AC-Lite). I chose the optimal tilt angle of…
This version is for UniFi AP AC LR, Lite model, other models may not be suitable. Print it to replace broken bases with PETG or ABS for rigidity, PLA is also recommended.
This model was originally on Printables where the creator posted his .step file for editing. It's been mixed a few times but as the smaller Max and Ultra Unifi models. This is for the Unifi Cloud Gateway Fibe r unit. It's a wall mount…
Źródło oznaczyło ten model jako treść 18+.
This is a key that inserts into the top of a Ubiquiti Networks UniFi AP to allow it to be removed from its wall mount. Insert into the slot on the top edge of the access point and twist left about 1/8 of a turn. The taper should be toward…
i made a mount for the Unifi AP's i got because no one is ever courteous enough to give you the old hardware or the new hardware that came with the new stuff they got to replace them with. so i made this to mount up my ACLR access points.…
I was looking for a stable desk mount for my Unifi G3 instant cameras that could be elevated more than the existing models I found. After printing the nanoHD DeskStand from BradleyB, I was impressed with the stability and desided to remix…
I was liking the layout of thing:3661633, but needed thing:1284641. I did not feel comfortable printing thing:1284641 out standing up, or even on its side with supports. Since I wanted the most strength, I decided to mix them, in a way.…
Small wall mount for the Unifi Flex Mini switch with holes for screws and on the bottom to connect a USB-C power adapter.
The Unifi Dream Router looks like an iconic droid from long time ago in a galaxy far, far away.... I came across this design but it wasn't really made for printing. I decided to clean it up to make it more printable. With it, the Unifi…
A small stand to prop up a Unifi WiFi 6 Long Range AP for placing on a desk/shelf/table. Print Settings Printer Brand: AnkerMake Printer: AnkerMake M5 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 10% Filament: Generic PLA…
Printed with 20% Infill with PLA. maybe increase the wallcount for more strength. You need 8x M4x16mm inHex screws. Phillips and Torx screws should work as well
From the original upload: I designed this 1U rack mount for the Unifi USW 16 Lite POE switch which fits the standard 19" racks with a depth of under 8 inches. The screw holes on the back are for M4.5x.75 as those were the spare screws I…
Remixed the original model in Fusion 360 so it could be repaired and remeshed as a single head. Created the .3MF with a hollow rod to unify the internals into a single body, but still look like 2 on the outside. This makes the body…
I recently renewed my network setup at home with Unifi devices. That included Unifi Gateway Ultra, Switch Lite 8 POE. At first I stacked them on each other but it would have bad effect like thermal issues and also not good in terms of…
it is largely based on Foden's design , which it also fits together with. I have also made a model for the Unifi Switch Ultra (USW-Ultra)
The switch is flat on top but is tapered on front bottom edge. As a result, two versions of the bracket are supplied. The standard mount is for a shelf mount. There is an inverted version that is better for mounting to a wall, hanging…
