489 modeli
Steam knob for Gaggia Classic pre-2015 model with 6 mm hole with flat side. It is a very tight fit, just push on hard! The flat side is internally reinforced.
Wydruk około 1,50 €–1,84 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Make sure to choose the correct plate version for your funnel (plate_GC_revised or plate_GCP_revised) Fasteners (to attach touchscreen housing): 2 M4x10 button-head screws 2 M4 nuts Loctite 242/243 or equivalent Recommended Print…
There is one main screen housing design, multiple mounting options. The Front mount is compact and needs fewer parts but is at a fixed angle and can be low for taller people. The Rear mount takes up more space and uses more parts, but the…
This assembly is for adding scales to your Gaggia Classic or Gaggia Classic Pro. Compatible with two HX711 boards or Vas' dual HX711 board. Requires 750 g load cells. Please use the assembly instructions at gaggiuino.github.io…
Notes: If you want to use this with an Arduino Nano build in a Gaggia Classic, please also print the Gaggiuino Optocoupler Case There are now two accessory parts: A stripboard mount and cable strain relief (see changelog). The stripboard…
Status: Released! Compatibility Warning! PCBv3.1 and PCBv4 (with onboard STM32 chip) are the only compatible PCBs. PCBv3 (which uses the WeAct BlackPill) is not compatible and should use the Protective Housing . Description This housing…
This housing holds the GaggiaBoard V3 (PCBv3, PCBv3.1, or PCBv4) from the Gaggiuino project, with maximum coverage to protect from a potential water leak. Design intent is for the board/housing to go in the corner vertically behind the…
This housing is designed to hold the Time of Flight and LED (ToFnLED) board for Gaggiuino over the water tank using magnets. The board slides in from the end, clipping in with the flex arm clip. If the board needs to be removed it can be…
Slim Drip Tray for Gaggia Classic that fits where the normal drip tray does. This adds enough room for a scale to fit underneath Also added a version with rounded edges for easier printing
This is a simple shield to prevent dust, debris, coffee splatter, etc. from entering the Gaggia Classic / Pro / Evo water tank. As a result, the water stays fresher for longer and biofilm takes longer to build up. There are 3 variants.…
This is a remix of the portafilter holder designed by teky929rr for the Gaggia Classic Pro espresso machine (base model found on Thingiverse ). The original design has been changed to be more stable, and includes a wider top clip and a…
printed in PLA 0.25mm 4 bottom and top layers
I designed this because i wanted something that look similar to my Eureka Mignon single dose hopper grabbed from here: https://www.thingiverse.com/thing:4703218 Added coffee beans looks like holes for some fancy look :) Printed with ASA,…
While many of my Gaggia-related models are specifically designed for the Gaggiuino project, this one is not. People requested a standalone version of my low-profile scales drip tray from the Gaggia Classic | Pro Scales , so here it is!…
This lever adapter for the Gaggia Classic Pro espresso machine slips over the existing steam knob. The Idea is to not disassemble the existing one. I printed it with PETG, because it has a little bit more thermal resistance, is a bit…
Warning - I'm hearing reports that Gaggia has recently changed the pump area screw locations, so if you have a 2026 or later E24 the holes may not match up. 2024-07-02 - New Alpha rev, note that instructions are not complete: Same base…
Minimalistic tamping station for the Gaggia Classic portafilter. This is an improved version of Jason's design, with more space for the portafilter and rounded corners at the handle cutout.
8/7/2023 As requested, I have added a version for the OME Drip Tray This is a drip tray float for NV_WoodCraft's https://www.thingiverse.com/thing:4254986 low profile Gaggia Classic drip tray. The shape will work on the original drip…
Requires supports to print
All smthng display housings for GaggiMate: https://www.printables.com/@dubios42/collections/2861668 Support my work: https://ko-fi.com/modsmthng Latest update (12 June 2026): Reduced the screw hole diameters, increased the wall thickness…
My version of a dimensionally accurate Gaggia Classic housing model, used to check fit on components for the Gaggiuino project. Note that this is not a Gaggia Classic Pro model. The main body is sheet metal, so manufacturing is probably…
Fork of project site: Open-Espresso/gaggiuino-builders: A Gaggia Classic control project using microcontrollers. (github.com) Discuss: Gaggiuino Builders | Facebook You can buy these printed here at www.matter-replicator.com For use with…
Has your Gaggia Classic ever splashed water up out of the drip tray? It's a pretty common problem. Common enough that on the original Gaggia Classics a splash guard plate was placed above the drip tray, below the grate. Its job was to…
Dosing funnel for the stock 58mm portafilter that comes with the Gaggia Classic Pro Category: Food & Drink
Heavily inspired by rotf101's tamping-station (but created from scratch) - see "model origin" for link. I made this for my bottomless portafilter that come with my 2nd hand machine. I have a shades of coffee wooden handle that I fitted to…
Before pushing the display into the housing, please make sure that the flat cable is centered over the cut-out. It is best to familiarize yourself with the installation instructions before installation (found in the files). All smthng…
Replacement knob for steam valve for Gaggia Classic. Adjusted for ergonomics.
On the Gaggia Classic there's a slight gap between the top of the water tank and the machine body I found a bit annoying after installing an LED above the tank. Every time I would bend down to watch my sweet shots I would momentarily get…
The material was PETG, layer height 0.20mm, 20% infill with support everywhere. The only supports to remove will be between the side brackets and the back side of the front bezel. The idea behind the chassis's shape around the switches'…
Tamping Station for Gaggia Classic. Storage for 58mm or 58,5mm Tamper.
This slim tray allows the use of taller cups and scales with all Gaggia Classic models, including Pro. The most difficult part of printing a drip tray adequately is getting it water tight, and the bottom part of this model helps with…
A replacement water reservoir cover with a place for two 58mm or 58.5mm tampers. For the Gaggia Classic Pro. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 200 Infill: 15%, doesn't really matter…
This purpose of this optocoupler case is to provide an easy upgrade path for those who want to start with the Arduino Gaggiuino build in a Gaggia Classic and then upgrade to the STM32 Blackpill. Print this case for use with an Arduino…
I made a new magnetic funnel for my portafilters. I own a Bezzera BZ10 (used to own a Gaggia Classic) and an open basket portafilter with an IMS B702TH26.5M basket. The Outer Diameter is about 70mm for my portafilter. The E61 variant has…
Holders for both the XIDIBEI transducer and the Seeed Studio transducer. Any VHB tape (very high bond) should work. The zip tie holes are 5 mm x 2 mm. Fusion 360 files included.
All smthng display housings for GaggiMate: https://www.printables.com/@dubios42/collections/2861668 This is a remix of the version for the LilyGo 1.75 Amoled real pictures. The basic housing fits very well (Var0 and 1). The individual…
Gaggiuino and IUIUIU branded Gaggia Classic | Pro drip tray cover with files for 3D printing, laser cutting, or sheet metal fabrication. Print: PETG, 4+ top and bottom layers, make sure layer adhesion and flow is good. You don't want…
I printed it with generic PETG 0.2mm layer height. Printing upside down (threads facing bed) does not need supports. Dimensions Height: 23 mm Spacing between tabs: 23.5 mm
Credit - I've tested a few dosing funnels on Printables before designing this ( E61 Dosing Funnel , Gaggia Dosing Funnel with Magnets ), so I'm sure my design is somewhat influenced by those. That being said, this is a ground-up new…
The stock steam valve knob on the Gaggia Classic Pro espresso machine is very glossy and slick. This makes it difficult to grip and control. This model is a simple ring with a knurled pattern that fits over the steam valve knob and is…
Here is a range of cases to enclose a 2.4", 2.8" or 4.3" Nextion screen for the Gaggiuino project. The case mounts magnetically to the front of the Gaggia Classic using 2 (or 4 if you want to be really secure) 60x10x3mm Neodymium magnets.…
The stock grate was all scratched up and ratling so i made one out of petg
I wanted a top tray for my Gaggia Classic to keep things cleaner and ensure no grounds fall down the edges of the lid from storing the tamp up there. The tray uses little material and is a tight fit but because it is thin I think it…
A Gaggia Classic replacement steam knob. There's a hole in the side which is intended to be tapped M4 to accept a setscrew to tighten down on the flat of the steam valve shaft (Note: this thread is not 3D printed and will require to be…
I made two versions of this: Single Part: no supports while printing no assembly after printing may be prone to warping while printing Two Part: no supports while printing some assembly with superglue after printing optional: use some…
This hanger was made to help better use vertical space in my cramped coffee corner. The tamper I designed around is the Normcore Coffee Tamper V4 and the included metal dish can be pressed into the recess, or popped out easily via the hex…
Simple bolt used to hold the screen in place for the Gaggiuino
Lowered and extended drip tray for gaggia classic. It can fit up to 17cm scales. Fit original stainless cover perfectly flush. Also have two bottom “nipples” which fit holes on the body so it wont slide anywhere. Front side sit flush on…
This portafilter is the result of my quest to reduce the number of espresso accessories on my counter. It's bottomless, fits standard Gaggia-compatible portafilter baskets, and best of all, lays down flat on the counter for one-handed…
This is a simple knockbox that fits well with the Gaggia Classic pro, because it uses the same angles and scaled dimensions. The rod dimensions are 20x20x140. I used oak in my case, but of course you can also just print the rod -stl.…
Snap-on covers for TE 160783-7 (and other variants) boiler terminal connectors used in Gaggia espresso machines. Crimper Jaws are here: https://www.printables.com/model/673240 Materials: Nylon (PA12) has been tested. Ideal materials would…
I really like this extension because you can take out the scale to use on the counter and the drip tray just rests on the sides of the base. It is a low profile drip tray, I need to drain it after each flush-brew-flush cycle. Cleaning is…
Direct replacement for Gaggia Classic water tank funnel. For FDM, print with funnel up and use support material for the square cutout and finger relief clearance (support material isn't needed inside the funnel). Material: PETG/ABS for…
NOTE: For an easy upgrade path to the STM32 Blackpill build print the Gaggiuino Component Housing and Gaggiuino Optocoupler Case (for GC) instead of this. The housing was originally designed for M2.9x6.5 self-tapping screws. These are the…
Should fit the following models: Gaggia HD8749/01 - Naviglio HD8749/11 - Naviglio RI8260/01 - Velasca RI8263/01 - Velasca RI9304/01 - Platinum RI9304/11 - Platinum RI9304/21 - Platinum RI9305/01 - Brera RI9305/11 - Brera RI9700/60 -…
Status: Released Description: This design houses the Gaggiuino Headless E177 PCB and provides mounting options for the outside of an espresso machine. Lights, buttons, and USB-C port are accessible with the case installed. There are 2…
Tamper Station Gaggia Classic
The OG model is perfect , but I wanted to add these magnets for a better hold on the funnel, especially during wdt. This should take 2 6x3 mm magnets, and the grip is pretty good
With the original 25mm Long Tab base, one of the long tabs hit against the handle of the gaggia portafilter, misaligning it. In this remix, the tabs have been readjusted allowing the Umikot to fit nicely on a JoeFrex Gaggia portafilter.…
Most Gaggia Classic owners are dealing (or living) with a dripping steam wand because the steam valve's metal-to-metal seal will break down over time. This drip chute will collect the water drops and send them to the drip tray. This drip…
Envious of those cool-touch espresso machine steam wands? It's easy conceptually - just run a PTFE tube down the center. However, getting everything the correct dimensions to make it work and fitting things together is a bit of a…
Please note that this case does not have a frame around the glass and therefore offers less protection! Alternatively, I recommend version 2 of this case with a frame! Before pushing the display into the housing, please make sure that the…
This simple 3d print was created to cover the gap between the water tank and Gaggia Classic body and prevent coffee splatter from entering the water tank. Doing this prevents gunk buildup at the bottom of the tank considerably, keeping…
A remix of the GaggiMate pro pcb cover that will print with out supports. You will still need the base available from the projects GitHub HERE Thanks to all the GaggiMate team for being so friendly and helpful.
This is a Remix from Damek’s design to be able to use his design with bottomless portafilters, as they differ a lot on sizes. I made this portafilter holders to be compatible with Shades of Coffee’s bottomless portafilter , other…
I printed on an Ender 3, using default settings except for 0.12mm layer height and matte PLA (for aesthetic reasons), 50% gyroid infill, and support material for overhangs >60deg. The screen is flipped 180 degrees vs the default build, so…
Nextion 2.4 inch display enclosure that fits the front panel of Rancilio Silvia V6. Intended to be used as part of a Gaggiuino install. The design leverages the V6 power and boiler indicator lights to route the wires to the screen. It…
I created the drip tray to be used with this scale from amazon. Most of the low profile trays didn't appeal to me and the higher stock tray had no clearance once you put a scale on. With the recessed scale, you have plenty of clearance…
I wanted a 20 degree front screen mount for the new Gaggiuino Gen 3 housing that had consistent outer surfaces, surrounded the switches, and preserved the outer status lights. @Livius accomplished this for the old screen, so I adapted…
Hello! Welcome! I've redesigned the mount so hopefully it is easier to use and doesn't require the extra soldering the original needed to move the connector. It is designed so that the screen can be plugged in and then slotted into the…
25/02/2026 - It's been 4 years, but I've finally removed the rogue part from the underside of the model and updated the page. Apologies to anyone affected. Upgraded version of my original water reservoir cover for the Gaggia Classic Pro .…
A remix of the GaggiMate pro pcb bottom. You will still need the cover available from the GaggiMate GitHub or you can use this remix for an easier no support print. Superglue or epoxy the 6x3mm magnets into the underside and then assemble…
Replacement for Gaggia Classic or Pro water tank funnel. This incorporates a tube to increase space inside the machine and for a smaller/quicker print. Photo 2 shows the stock funnel superimposed over this design. Print in PETG for heat…
☕ Gaggia Classic Drip Tray for Bookoo Themis Ultra Scale This is a custom drip tray for the Gaggia Classic , designed to fit the Bookoo Themis Ultra scale perfectly 🎯 🧩 Two versions included: Standard version – compact and clean, ideal if…
This is a mod to use a scale under the gaggia classic to use all the space under the portafilter. The legs are press fit to the rubber feet of the machine so you should not remove them. Measure and scale in the slicer the z axis if needed…
31/08/2024 - This model is still under development. 7/09/2024 - An option has been added where the middle section of the pump mount is removed. This model is intended to replace the original pump mount (including the metal plate) for the…
I loved this espresso accessories shelf , but it didn't fit the offset lugs on my Gaggia Classic Portafilter. I designed this one with two Ø64.5mm spots for a tamper and a WDT tool, and a hanger that fits this funnel I designed for IMS…
There are multiple versions, for the FDM versions there are STLs with and without built-in supports: Stock model (for reference or SLA printing) FDM printable version, for stock 7.5 mm bulb assembly FDM printable version, for 5.8-6.2 mm…
As I didn't found an enclosure that checked all the boxes, I've designed it myself. It's a an enclosure with a print in place hinge and embedded magnets. Has the space for the soldered wires that are going to stick through the back. The…
This is a portafilter holder, it is meant for a wall on the left, with the handle facing you. The weight of the handle keeps it screwed in, but its super easy to remove. I created this for the Gaggia 58mm portafilters, but it should work…
Ah, the world of 3D printing and espresso converge in a delightful blend of open-source ingenuity. Imagine a drip tray for the Gaggia Classic Evo Pro, not just any tray, but one that's as carefully layered as the flavors in a perfect…
Original drip tray has fixed position. When user want's to make a shot (double shot) into a taller cup/mug, first has to pull a shot into a smaller cup and then pour the shot into the desired taller cup. Having an optional drip tray…
This model is a remix of Loogle's Gaggia Classic / Pro touchscreen enclosure. That model is a remix of a project from LikeableBump. Consider visiting these projects and liking them!…
DEPRECATED AS OF 2024-01-22, use the protective housing instead ( https://www.printables.com/model/370513/ ) This housing holds the GaggiaBoard V3 from the Gaggiuino project, designed to be as small a package as possible. Variants: There…
Stop water leaking all over your kitchen counter! The Gaggia Classic Pro (2022) Gaggie Leaky Steam Wand Drain To Drip Tray is the cheap and basically free solution is here! I have owned a previous Gaggia Classic that also exhibited the…
My take on the GaggiMate Pro v1.1 enclosure. Uses the original pro base available on the Gaggimate GitHub here: https://github.com/jniebuhr/gaggimate/blob/master/stls/pcb/gaggimate-pro-rev1/pcb_base_clipped.stl
Raised feet for the Gaggia Classic, giving extra clearance under the steam wand. A simple remix of https://www.thingiverse.com/thing:5235766 , as the TPU I have is too stiff to to fit through the mounting holes on the base of the Gaggia…
Normcore 58mm Portafilter Holder for Gaggia Classic. Better for drop packing than more minimalist holders. I've included a pretty decent estimation of the PF itself
Here is for beautiful Bookoo Themis Ultra drip tray for Gaggia Classic and Pro in 3 heights High of dip tray (30mm/39mm/45mm) Watercapacity. (250ml/400ml/600ml) The Lid is available to fit with or without rubber cover.
[UPDATE 01/11/2026] Added Gen 3.5 (P4) screen housing parts and updated front and rear mounts. This project is aimed around increasing the suitability of Loogle's amazing designs for the Gaggiuino project for printing ASA/ASA (or…
This case fits the Gaggimate pro board. It allows the board to be attached to the rear of the case.
Overview Enclosure for a 4pin magnetic pogo connector for Gaggia Classic and Gaggia Classic Pro. One pogo pin connector is for Nextion Display. Second is for programming STLink. Designed for #6-32 x 1in screw but can be adapted for…
An ultra low profile drip tray for Gaggia Classic Pro machines. This drip tray allows a full size mug or glass to be placed under the portafilter for those that prefer to pull shots directly into their cup for lattes or long…
This housing contains the components needed to upgrade the Gaggia Classic Pro. The housing replaces the water lid (slides down into the slot). The following are the upgrades. Mr. Shades PID controller 40mm Pressure gauge Pump dimmer There…
Print on end! Fits on the purse mini bed if rotated 45 degrees.
Holder to attach to the side of the Gaggia Classic and hold a espresso shot mirror (link below). Printed in PLA. If I print again, I would mirror it so that the opening faces the back of the machine (if you position the mirror on the left…
This is a 58 mm portafilter holder for the Gaggia Classic Pro that prints with no supports and is meant to be adhered to a wall or cabinet using double sided tape. This model is very simple (it is symmetrical) and may work for other…
A PCB case for GaggiMate Pro that allows you to mount the PCB on the outside of the Gaggia Classic at the rear. You might want to do this if you're struggling for space inside or want easier access to the USB port. The two halves of the…
Gaggia classic portafilter dosing funnel Frustrated with other designs that didn't fit my portafilter, I designed my own. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Infill: 20% Filament: Hatchbox PETG…
Cable clips, for clean wiring of the Gaggiuino Mod. Suitable for 18AWG high-voltage cabling as well as 22AWG low-voltage cabling. Should be printed from heat-resistant material. At least PETG, better ABS.
