Liczymy pasujące modele…
The stock Elecraft AX1 and AX2 clip for the bipod is very stiff, difficult to attach, and hard to remove. At the request of a fellow op, I designed a better one. Here it is. Print in PETG for flexibility and durability. Print the clip…
Wydruk około 0,12 €–0,15 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Complete Yagi Antenna Clamps Collection — Universal, Dedicated & 6m Heavy-Duty (Boom 15 to 30 mm) A popular, highly versatile antenna clamp collection designed to fit multiple Yagi antenna configurations. Thank you to the ham radio…
Wydruk około 0,72 €–0,89 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This little bracket makes it easier to construct an ultra-light directional radio antenna using aluminum arrow shafts. The bracket slips onto an arrow shaft which acts as the antenna boom and allows simple attachment of arrow shafts to…
Wydruk około 0,45 €–0,55 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Shark fin cover for the roof antenna of your W639. Print using PETG, ABS or similar heat resitant material. Two verisons are supplied. 1. The regular one with thick walls ment for translucent filament and a recess to hold the Sika Flex…
Wydruk około 6,61 €–8,08 € nettoWstępna wycena dla PETGMateriał u źródła: PET
BACKGROUND: A little bit of gain can make a big difference in an HF radio antenna, and one of the simplest and smallest gain antennas is the Moxon Beam. Now you can easily build yourself a portable one for the 10 m band with some 3d…
Wydruk około 0,36 €–0,44 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This Fox hunting antenna is constructed using 3d printed element holders (PETG, 20% fill) and easy to acquire material from a hardware store. It is a remix of thingiverse 912567 but optimized for a small, hand held UHF HT rig carried for…
Wydruk około 4,12 €–5,04 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a design I whipped up to provide stabilization for the BNC connector on an IC-705. It utilizes the ground lug and the little handle thing on the back to provide 2 points of solid connection. Print instructions I printed this with…
Wydruk około 1,37 €–1,68 € nettoWstępna wycena jednego wariantu
A simple clip to pass antenna wire through and to be held by a carbon 6 pole or pretty much any fishing pole with a decent enough top section (i.e. not the very fine squid pole types). The simple version should be adequate for most…
Wydruk około 0,07 €–0,09 € nettoWstępna wycena jednego wariantu
Holder for GPS, VTX Antennas (in my case DJI O3, but others with SMA adapters also work) and a fixed XT-60 for easy plug in of the battery. Print the main part in TPU and two spacers in a rigid material like PETG or PLA. The advantage of…
Wydruk około 0,15 €–0,19 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Note - after making this part I learned that these antennas have magnets in them: https://www.reddit.com/r/pcmasterrace/comments/wtxpqq . I still like the way this part looks better than using the magnets but you might prefer a different…
Wydruk około 2,06 €–2,51 € nettoWstępna wycena jednego wariantu
The stock tailpiece for the iFlight Nazgul Eco frame had an angled XT60 connector, which made it impossible to position LiPos with short wires properly. This set has original XT60 and SMA connectors in better positions and has space for a…
Wydruk około 0,81 €–0,99 € nettoWstępna wycena dla PETGMateriał u źródła: PET
When the potential for lightning is possible or when not using your station, You should disconnect your antenna wires to prevent inadvertent lightning damage to your Transciever or Amplifier. This holds three RG-8 antenna lines. This…
Wydruk około 2,10 €–2,57 € nettoWstępna wycena dla PETGMateriał u źródła: PET
3D print elements for Double Bazooka antenna. Use RG-58 and 300 Ohm ladder line. Designed for UHF connector. I printed my elements from black PETG, you can use ASA for A class durability. I recommend filling boxes with epoxy resin in…
Wydruk około 3,06 €–3,74 € nettoWstępna wycena dla PETGMateriał u źródła: PET
In case a rc model's fuselage hull is painted with colors that are containing metallic particle it's recommended to place the 2.4 GHz antenna outside the fuselage. This semi-scale antenna body can be mounted outside the fuselage and has a…
Wydruk około 0,66 €–0,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a scale 1:3.5 side-rudder antenna model (with holes for 2.4 GHz antennas) for the L-39 Albatros. Part 3 provides enough material to sand it to fit it to the profile bulge of the fin. Part 2 is meant to add more stability and…
Wydruk około 2,82 €–3,45 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I got this idea from a print on Thingiverse but it was a plug insert that was intended to be printed with flex. I opted instead to turn it into a nut and bolt and use PLA. Link to the original idea here . I exclusively use either an…
Wydruk około 0,49 €–0,60 € nettoWstępna wycena jednego wariantu
This is an antenna or pole holder for a bar mesh fence (exactly for the fence post). I use a standard antenna pole (43mm) for a rain gauge. Maybe you have an other use case. I use two of this pole holder. The object not shown in the…
Wydruk około 1,21 €–1,48 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is an holder for the antenna (calculator) of the direct TPMS for VW/Audi cars. Best use is when you retrofit the direct TPMS system. Like this no need to put the antenna in the rear bumper as OEM, you can put it in the trunk next to…
Wydruk około 1,85 €–2,26 € nettoWstępna wycena jednego wariantu
Base support for antenna mast to prevent slipping when guy wires are used. It also has a groove for guiding the antenna wire inside the mast. Filament used is PETG. Used 4 perimeters, 5 solid layers for top and bottom, 15% Gyroid infill.…
Wydruk około 3,94 €–4,81 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The FrSky XM+ receiver has very fragile antennas that often get damaged if you don't handle them carefully. To fix this, I designed this case to hold the antenna wires in place and provide a good surface for gluing to the fuselage. I've…
Wydruk około 0,11 €–0,14 € nettoWstępna wycena jednego wariantu
This is a simple antenna shield and mount for the R9MM Immortal T antenna to the Arris Hobby E280 7" drone. But a few Zip-Ties will fasten the mount to any drone. The TPU printed antenna shield will require a few zip-ties to secure…
Wydruk około 0,67 €–0,82 € nettoWstępna wycena jednego wariantu
Do you wish you could attach something to your Arrow Antennas Yagi boom? Look no further! Print in PETG. Use a ¼" 20 - ½" bolt.
Wydruk około 0,30 €–0,37 € nettoWstępna wycena dla PETGMateriał u źródła: PET
An antenna mount for the TBS Source One (V0.1.1) frame. Print instructions Category: 3D Printing Overview and Background Designed to fit standard antenna tubes with an outer diameter of 3mm, for use with FPV quadcopter receivers. There is…
Wydruk około 0,88 €–1,07 € nettoWstępna wycena jednego wariantu
No straps. Fragile during crash.
Wydruk około 0,17 €–0,20 € nettoWstępna wycena jednego wariantu
Small wheel for shortening this TV antenna . It's used on campervan, but can be used anywhere. Might need a bit of modifying, because the teeth don't allow the antenna to stay paralel. Printing instructions Layers: 0,20 mm but doesn't…
Wydruk około 0,45 €–0,55 € nettoWstępna wycena jednego wariantu
See original description . This is a support-free remix of the original design by OK1HRA, published with his permission. I redesigned the parts so they can be printed without supports. The small locating pin is now a separate part and…
Wydruk około 1,39 €–1,70 € nettoWstępna wycena jednego wariantu
external micro antenna mount for uconsole
MR (ANT) TENNA FROM DELTARUNE
This is a set of files to build a 2m and 70cm moxon antenna. Inspired by David (DL1DN), known on youtube as “QRP lifestyle”, but his design was not available for DIYers. So I decided to design it from scratch and pusblish it for others.…
Antenna end insulator, for attaching end of wire antennas to support lines. Designed for print-ability, structural strength, minimal chafing of wires and lines. When printed at 70% scale (recommended size) or more, exceeds typical support…
Unable to find a good antenna winder for portable amateur radio operations, I started tinkering with designs. A few iterations in, I came up with this one. Dimensions are approximately 140 mm x 55 mm x 5 mm. It provides room for up to…
Easy to use compact and lightweight endfed antenna for HF bands. Deploys in seconds – ideal for POTA activations and preparedness scenarios. Requires use of mast, tree or another raised point anchor point. BNC male connector. Short run of…
Altered the design so that the connectors have space as well as the cables. Also the back is enlarged to match for the thicker footprint of the board. The buttons are slimmer, the reset button is harder to press.
There are a few options with this one, mainly due to requests and iterations. there is an option with and without the hinge. there is a v1 and a v2 of each as I didn't like the wobble on the plates. and there is also an option to have one…
Full tutorial to be found on the RAspberry Pi website .
I wasn't really happy with the alternatives and wanted a mount that would blend in well with the antenna and the wall. My copy printed in Prusament PETG on a Mini with 0.6 nozzle, input shaper and 0.25 mm structural setting. I hope the…
Seii-Radiomaster_Boxer_Antenna_mod_adapter_v7_PETG - I took Bikernickmn's model and just polished that widest square piece because it was damaged in the original file. Also, whole file is not properly centered by the original author and…
Need a way to store your lightweight wire antenna for Summits on the Air or Parks on the Air activations? This winder fits 70 feet of 26 ga wire or smaller for a 40 m end fed halfwave or random wire antenna built from one of my kits from…
Simple 90 degree angle mount for the Segway Navimow i105e/i108e antenna. Designed to be printet without supports. Really sturdy with these print settings: 0,2mm layer height 3 walls 5 top and bottom layers 25% grid or gyroid infill If you…
Material: Pet-G or ASA 275 or ABS
These are designed to slip onto a thin metal headband. Printed in PLA at 100% infill with print thin walls enabled.
Ground Plane Antenna 868MHz (or for other frequencies like 433MHz or 915MHz) for Meshtastic or anything else i used 1,5mm² (1,4mm diameter) copper wire to find in Europe in the standard NYM cable or AWG 14 or 15 in the US -stretch the…
I designed this Shark Fin Antenna cover to replace the OEM degraded Antenna Bee sting in my Mitsubishi ASX. Printed in Dark Silver which matches with the car color. Print in PTEG for heat and weather durability. Printed without support.…
The original Buddy3D camera for the 🥰 Prusa CORE One comes with the Wi-Fi antenna freely hanging outside the housing 🫣. This not only makes it look unfinished but also leaves the antenna vulnerable to damage. The flexible part of the…
3d printed case to DIY build your own dipole antenna. It will fit up to RG316 coax size pigtails.
I was unable to find a suitable model for an ELRS antenna holder that fits the GepRC Mark5, so I made my own. Additionally, I designed a version that allows for spacers, made of a more robust material like polycarbonate (PLA would…
The part accepts a BN-220 GPS module, a standard vTX pigtail with a flange mount, and standard 3mm antenna tubes (included with the Mark5 frame kit) Prints without support. Can be printed in PETG or TPU, depends on what you prefer. Photos…
Remix for use with Meshtastic Requires SMA crimp connector, a piece of heat shrink tubing, and RG174 cable or similar diameter. Glue the connector with the crimped cable into the antenna using 5-minute epoxy or another glue .
A simple antenna mount for the T-mount stock IMRC Ghost receivers antennas. For QUADMULA SF3 To install the T-style antenna into the Mount, slide one side of the white part of the receiver into the mount, then flex the mount to about 90°…
Bracket for mounting an SMA antenna socket for different applications. In my case an ESP8266 with u.FL socket and external antenna. Socket with external hex locks by itself into housing. Therefore easy mounting No supports necessary.
I needed a mount for a single SMA adapter, an 18mm x 18mm GPS, and an XT60 connector. There was no such variant among the models provided by Speedy Bee, so I took the closest original model, which already had mounting for the XT60 and SMA…
This model is compatible with the lego system.
Can not be used by katcaps
All components to print a center insulator, end insulators, and line tensioners to build a QRP dipole antenna for ham radio. I designed this for use with 6-32 screws, 18 gauge wire, SO-239 connector and 550 parachute cord. The antenna…
3D printable 5-loop and 6-loop helical directional antenna to be used on 5.8GHz FPV video receivers (e.g. FPV goggles). We reached more than 600 downloads! If this model is helpful for you, a quick ❤ will help other makers and pilots find…
Designed to be Printed on an FDM. Make sure Detect Thin Walls are enabled. There is a bevel in the sides to make location of assembly easier. Make sure the model is printed flat on the build plate with the thickest part of the bevel down.
I loved the design of the slim snap-together OrangePi Zero 3 case by Gerber but I also wanted the antenna mount from the case by TheParanoidEngineer , so I combined them :) Make sure to route the antenna cable through the notch in the…
Companion project to my other parametric configurable FPV designs: Pod | O4 | Frame Whoop Action2 , 3-5 AcePro GoPro Mini Hero 9-12 Antenna Mount Get your perfect antenna setup for your FPV drone. Mix-and-match from 80 frames, 50…
Hey there, I have created this model to upgrade my GPRC Mark 4 frame with the new DJI O3 air unit. I have made 2 Version: Version 1 with DJI O3, antenna and GPS mount: The bottom left and right part to hold the DJI O3 Air Unit in place.…
Unable to find a good antenna winder for portable amateur radio operations, I started tinkering with designs. A few iterations in, I came up with this one, then parsed it down to just a wire frame for minimum weight. Dimensions are…
Designed this for my /P operation. Top hole allowes it to hang in inverted V setup BNC Connector compatible Donations for new trx are more than welcome via paypal
Camera mount - print in PETG. Antenna mount - print in hard TPU (70 D or harder) and use cable ties to fix antennas in place. Supported camera ange is from 0 to 30 degress (the mount is slightly in frame at 0 degrees). When printing…
This is a remix of tpatrickwalsh's TTGO T-beam v1.1 (and v1.0) case ( https://www.thingiverse.com/thing:4753247 ), modified to fit the bigger GPS antennas for better reception. I have found that the bigger antenna is a must, as the…
I created this antenna winder for SOTA activations, but of course you can use if for non-sota activities as well. The winder serves a second purpose as a strain relief for an endfed antenna and the paracord used for fixing the antenna to…
This remix adds a clip for a Female BNC connector. The position of the clip will work with both the QRP and 20 W versions of the K6ARK Portable Radio antenna kits. Unable to find a good antenna winder for portable amateur radio…
If you don't have a printer, I do sell them(velcro included) on my site for cheap with free shipping for those in the USA. https://shop.ke9bos.com/ This is something I made for my ham radio adventures. This has been really helpful for me…
use vhb tape for antenna
This remix adds a clip for a Male BNC connector. The position of the clip will work with both the QRP and 20 W versions of the K6ARK Portable Radio antenna kits. Unable to find a good antenna winder for portable amateur radio operations,…
Custom wall mount for Mammotion Luba - this fits all their models (AWD 1000, AWD 3000 & AWD 5000). Greatly enhances the performance of the RTK antenna if you have buildings that are blocking the transmission of the signal.
By increasing the thickness of the shell, it was possible to place external antennas and leave room for other modules in the future. Main features: free space in the shell for other modules; fastening only with magnets (8x2 mm); holes for…
This is a compact ventilated enclosure for the Seeed Studio XIAO ESP32-C6 , designed for a stable Zigbee router / range extender setup. Features USB-C access SMA bulkhead mount for an external 2.4 GHz antenna (via u.FL → SMA pigtail) No…
I modified my Packtenna EFHW to work on 20m and 40m with a extendable link. I got the idea from a K8MRD video, but didn't care much for how he had the organization (both wires on the same winder). I've got this winders profile setup to be…
So for those that have been following me for while on youtube and TinyGS, here is another treat, I have been working on multiple versions of a modified QFH antenna to get the smallest size and while keeping decent performance. This file…
Guy Insulator for antenna towers, guy lines, sailboat back stay antennas, and anywhere you may need such an item. Designed with 10mm hole for your line or wire. Easy to scale to whatever size desired. I like 100% and 80% for my needs. If…
I've modified the original Mammotion Luba RTK Antenna Wall Mount to include a hole along the length of the stem, allowing the cable to exit downward. This update provides an alternative solution for cable management, especially if routing…
Simple housing with sliding lid with a secure “click” closure. Many thanks to TuTu for the fantastic template! Hint: Switch off via the meshtastic app, switch on by pressing the reset button. This saves an additional switch. Battery: I…
Insulator for wire antenna. Can be used as tension relief on the feedline side and as insulator on the supporting side. Also works as apex insulator for delta loops, inverted L, etc. If using 14 AWG knotting the antenna wire is not…
Original design by by LY3LP, recalculated by George M1GEO Dimensions and design: https://www.george-smart.co.uk/antennas/dual_band_satellite_yagi/ How to print: Element holders - 4 perimeters 20% infill no support - 6 Pcs Radiator holder…
A remix of the uConsole micro antenna 0.2 mount model for a countersink screw plus a mount for the other corner.
A small antenna stand for propping up antennas with sma connectors. Set up your sdr or handheld radio antennas in a better position easily with an sma-antenna cable and this simple stand. Printing: Printing upside down is recomended to…
I designed the mounting parts for this field-assembly antenna to be strong yet easily taken apart for transport. The “boom” is 20mm pvc electrical conduit, and the elements are 6mm solid aluminium rod. The mountings consist of a threaded…
The proposed solution is antenna winder which integrates UNUN in the center and contains two compartments, in first one thin coax cable such as RG174/U of length 2.5m and ended with BNC connector is wound, while in the second one the thin…
Slightly remixed case for a ESP32 with external antenna (works great with ESP32-WROOM-32U). I have messaged the original author and he's OK with posting new model. Added ventilation holes on both sides and modified the lid, which is now a…
Simple 90° angle mount for the Segway Navimow. I chose a design that is easy to print. I used PCTG for temperature resistance. 25% cubick infill 5 top and bottom layers 4 perimeters
A QFH antenna has an omnidirectional pattern with enough gain to operate either on the uplink or the downlink for communicating through the various amateur radio satellites that use the 2m and 70cm bands. These 3D printed parts can be…
From May 2026 availabe mount for motor rev F5, TNX OK1GOD! Four predefined sizes (S,MS,M,XL) M size max torque 2200 kg/cm (215 N/m) without destroy Included terminal for install motor from cordless drill Without nuts (tapered holes) DXF…
This is a remix of the Quadrifilar Helix Antenna by @ jhsandell for 1090MHz (ADS-B) The following updates have been made: The 'bug' that jhsandell noted where the code was using diameters rather than radii has been fixed This version…
Print in TPU. Use needle nose pliers to hold the SMA in the hole in place. Tighten the Antenna by hand. Its pretty tight, but the result is, that your Antenna wont move! I created different versions for different SMA Connectors! added GPS…
Simple housing with sliding lid with a secure “click” closure. Many thanks to TuTu for the fantastic template! Switch and charger board from amazon - see photo… The tabs for the screws must be removed from the switch. Simply bend them…
This is a 3D printed spiral support structure for the wires of a 435 MHz QFH antenna. The antenna provides a dome-shaped hemispherical pattern that is suitable for operation (transmit or receive) on various amateur radio orbiting…
Hey FPV Guys, it's a ugly quick'n'dirty combination of different Things. For the Speedybee Mario5 Frame: - WS Dual Antenna - XT60 Mountable Plug Connector - WS M181 GPS Print with TPU Infill 15% and Organic support
Note: these build instructions are preliminary - I'll try to update them with more detail when I have time, but I wanted to get these out there. BACKGROUND: 5 m telescopic whip antennas have become readily available and very popular…
General After reading an interesting artikel about Quadrifilar Helical Antennas I got inspired and wanted to print one The creation of this antenna described in detail at QFA Antenna . Models and simulations are available on GitHub:…
A small spanner (wrench) for SMA connectors for SDRs etc. Obviously it's not super-strong, but it's useful for tightening or undoing the connectors to finger-strength in tight spaces.
This is a box to hold an ESP32 DevKitC board with a grid board to solder on connectors or some electronics. The board itself is meant to rest on pin headers so that it remains removable. There is a hole for an external antenna. To use…
I print mine in ASA filament. You can also print it in Petg. Infill needs to be 100%. You will need a BNC female to female bulkhead connector 1 M4 x 18mm bolt with nut and washer 1 M4 x 16mm bolt with nut and washer 1 M4 thumb nut 14 gage…
This is a more compact handle designed specifically for the Elk 2m/70cm log periodic antenna, which I designed to be smaller than the PVC-based handle that it comes with from the manufacturer. This makes it handle a lot more like the…
A 1/4-36 thread with 5.5mm depth with added 0.05mm of thread clearance.
A jam proof pulley for antenna or other projects. The hing mount and the pulley mount have a matching diamond interlock that allows the pulley to be mounted in one of two orientations, depending on your needs. There are also mast top…
