P
PrintablesH3dSprint
Propeller with ⌀75mm for a shaft ⌀2mm
Part is printed with PETG and need partial supports.
- Pobrania
- 1263
- Polubienia
- 46
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesH3dSprint
Peristaltic pump - nominal diameter Ø8mm - for fluids like cooling water, water, engine oil and other similar
All designed parts of the peristaltic pump are printed out of PETG. For the hose I have choosen silicon to avoid high forces by rotating the impeller. The hexagon shaft where the impeller is put-on have two interfaces, on one side an…
- Pobrania
- 998
- Polubienia
- 236
- Ocena
- 4
P
PrintablesH3dSprint
Bevel gear - involute tooth system
The involute bevel gear is printed with PETG and need partially supports. Assembly instruction remove support and deburr edges if needed prepare adjusting ring (2x) by adding a hexagon nut M3 and a countersunk screw M3x12 prepare housing…
- Pobrania
- 467
- Polubienia
- 49
- Ocena
- 0
P
PrintablesH3dSprint
Space saving filament spool roller - suitable for width 50mm up to 82mm
For my filament box I wanted to have a spool roller with following features: Shall save space in the filament box. Enable easy replacement of filament spool. Shall work for 1kg spools with ⌀200mm. Shall be robust and avoid jumping out of…
- Pobrania
- 461
- Polubienia
- 75
- Ocena
- 4,8
P
PrintablesH3dSprint
Bottle cage for bike
The bottle cage is suitable for 0,5 liter PET bottles which you could buy in a supermarket. Due to low stiffness of PET bottles, the bottle cage is designed to work without clamping of the bottle. Other bottles with a bigger diameter fit…
- Pobrania
- 452
- Polubienia
- 108
- Ocena
- 4
P
PrintablesH3dSprint
Adapter to connect a hose to a thread G1/2 - ⌀ 7mm up to ⌀11mm
The adapter is designed to connect a hose to a thread G1/2". Available diameter for hose: 7 | 7,5 | 8 | 8,5 | 9 | 9,5 | 10 | 10,5 | 11mm Print instruction: material: PETG layer height: 0,2mm (0,3mm) nozzle: 0,6mm (0,4mm) support: no…
- Pobrania
- 428
- Polubienia
- 115
- Ocena
- 0
P
PrintablesH3dSprint
Hook for hanging towels, swimwear or clothing
Printed in PETG, the hook fits standard shower glass panels and is clamped in place by preload tension.
- Pobrania
- 423
- Polubienia
- 159
- Ocena
- 5
P
PrintablesH3dSprint
Bottle cage for kid bike with narrow frame
The bottle cage is suitable for 0,5 liter PET bottles which you could buy in a supermarket. Due to low stiffness of PET bottles, the bottle cage is designed to work without clamping of the bottle. Other bottles with a bigger diameter fit…
- Pobrania
- 356
- Polubienia
- 85
- Ocena
- 5
P
PrintablesH3dSprint
clear-transparent PETG - print glass
To print parts which looks like glass, I have checked different print settings for PETG. Overview Settings: Results: No printed part, indipendent of the settings, looks like glass without grinding and polishing. The most promising result…
- Pobrania
- 321
- Polubienia
- 72
- Ocena
- 5
P
PrintablesH3dSprint
Cap for clarinet mouthpiece
The original cap was lost, so I have found the clarinet cover of FeKo which I have adjusted to my needs.
- Pobrania
- 288
- Polubienia
- 28
- Ocena
- 5
P
PrintablesH3dSprint
Gear lever knob for tractor - e.g. for FENDT
The gear lever knob is designed for multipurpose use and not only for a special tractor. Thats the reason why the gearshift pattern is a seperate printed part. I didnt want to make several tests for a clamped part, so I connected the…
- Pobrania
- 279
- Polubienia
- 30
- Ocena
- 5
P
PrintablesH3dSprint
New legs for a Playmobil figure
Part is printed with PETG and need partially supports. To remove the original part, I have used a screwdriver. Otherwise you have to disassemble the figure.
- Pobrania
- 277
- Polubienia
- 53
- Ocena
- 0
P
PrintablesH3dSprint
Small nozzle for vacuum cleaner - extra long (pipe: ⌀35,5 mm, total length: 308 mm)
Print instruction: Orientation: print upright Due to the height of 308 mm, I recommend to add a support on the inner slope surface.
- Pobrania
- 250
- Polubienia
- 90
- Ocena
- 0
P
PrintablesH3dSprint
Side mirror suitable for Playmobil truck
Part is printed with ASA and need supports. PLA or PETG will be also fine.
- Pobrania
- 243
- Polubienia
- 26
- Ocena
- 0
P
PrintablesH3dSprint
Vaccum cleaner adapter for Makita router
The adapter is printed with PETG and do not need supports.
- Pobrania
- 236
- Polubienia
- 75
- Ocena
- 5
P
PrintablesH3dSprint
Box for multimeter with rotary lock
Design goals: store the multimeter with connected measuring cables in a box cover of box shall have a lock multimeter box shall stand stable if cover is opened to perform measurements Design: All designed parts of the box are printed out…
- Pobrania
- 235
- Polubienia
- 63
- Ocena
- 5
P
PrintablesH3dSprint
Tool to open lid of a watch e.g. for Fossil
The tool is printed with PETG and do not need supports.
- Pobrania
- 224
- Polubienia
- 32
- Ocena
- 4,67
P
PrintablesH3dSprint
Fitting to mount a PTFE tube to filament box
To lower drag force on extruder and support of my printer, Im using a PTFE tube between filament box and the extruder. Quality of print is increased due to low forces. Parts are printed without support and are made out of PETG. Tightness…
- Pobrania
- 200
- Polubienia
- 36
- Ocena
- 4
P
PrintablesH3dSprint
Tube connector to connect filament PTFE-tubes with an outer diameter 4mm
The connector is printed with flexible filament (Extrudr Semi-Soft) and do not need supports. To ensure good adhesion to the print bed, I recommend to use a brim.
- Pobrania
- 191
- Polubienia
- 22
- Ocena
- 5
P
PrintablesH3dSprint
Knife holder for grinding machine
The parts for the knife holder are printed with PETG and are in use for a grinding stone ⌀200mm. Part list: knife holder | quantity: 1 knife guidance | quantity: 1 threaded bar M10 | length: 100mm hexagon nut M10 | quantity: 2 cylinder…
- Pobrania
- 190
- Polubienia
- 34
- Ocena
- 0
P
PrintablesH3dSprint
Protector for sharp table corner for different sizes of table leaf
The protector is printed with PETG and do not need supports. The protector is plugable and work without glue or any other fixation. I have added different .stl files of protectors which should fit to most common thickness of table leaf.…
- Pobrania
- 186
- Polubienia
- 32
- Ocena
- 5
P
PrintablesH3dSprint
Railroad crossing for curved track - toy train
The railroad crossing is build up by 5 parts to get a smooth surface for the road. To connect the parts of the inner and the outer curve, I have designed a dovetail guide. The parts was assembled in a vice to avoid tilting, but it should…
- Pobrania
- 181
- Polubienia
- 30
- Ocena
- 0
P
PrintablesH3dSprint
rectangular sealing ring kit - ⌀8mm up to ⌀33mm
Sealing rings for air, water and other liquids (depends on used material). Available sizes are shown in table below. Difference of form A and B is the width of the ring. Table 1:
- Pobrania
- 173
- Polubienia
- 71
- Ocena
- 5
P
PrintablesH3dSprint
Adjustable chamfer tool for chisel
The chamfer tool is printed with PETG and do not need supports. To assemble the chamfer tool, use cylinder screws M3x15 (2x) and hexagon nuts M3 (2x). Adjust the tool on your chisel to get the required size of the chamfer.
- Pobrania
- 156
- Polubienia
- 60
- Ocena
- 5
P
PrintablesH3dSprint
Trumpet holder for music stand
Trumpet holder is printed with ASA, grinded and smoothed with aceton where trumpet is in contact with the holder. To assemble the trumpet holder, you need a hexagon screw M4x60 or you make your own by cutting a threaded bar and adding 2…
- Pobrania
- 151
- Polubienia
- 36
- Ocena
- 5
P
PrintablesH3dSprint
Mixer ⌀70mm for rod with thread M8
Working direction of the mixer is clockwise. Before printing, decide if you want to mix the liquid up or down and select the related .stl file. Print instruction: material: PETG (recommended due to solvent resistance) layer height: 0,2mm…
- Pobrania
- 147
- Polubienia
- 49
- Ocena
- 0
P
PrintablesH3dSprint
Holder for jet gun - suitable for Kärcher K5.80 high-pressure cleaner
The holder for the jet gun is printed with PETG. Part list: jet gun holder | quantity: 1 hexagon nut M3 | quantity: 1 cylinder screw M3x10 | quantity: 1 Print instruction: Place the holder with the flat surface to the print bed (similar…
- Pobrania
- 141
- Polubienia
- 18
- Ocena
- 5
P
PrintablesH3dSprint
base plate for Bosch jigsaw
Features The design of the base plate contains some enhancements: protection of sensitive materials due to smooth plate surface anti-splittering feature finder sight printed dimension from outer edge of base plate to saw blade Print…
- Pobrania
- 135
- Polubienia
- 31
- Ocena
- 0
P
PrintablesH3dSprint
Spare part kit for plug-in coupling 1/2“ - suitable for Gardena
The parts are printed with Extrudr semisoft (shore hardness 85A) and do not need supports.
- Pobrania
- 123
- Polubienia
- 26
- Ocena
- 0
P
PrintablesH3dSprint
Towing eye for trailer - suitable for Rolly Toys kid tractor
The new towing eye of the trailer is adjusted for a Rolly Toys John Deere 7930. The original height is designed for rollyKid tractor. The adjusted trailer fit also to the smaller tractor. The part is printed with PETG and a layer height…
- Pobrania
- 120
- Polubienia
- 20
- Ocena
- 0
P
PrintablesH3dSprint
Transport roller for e.g. EURO-box
The roller is built up by four printed connectors and wooden slats and can be customized to any size of boxes. Part list: connector | quantity: 4 countersunk screw ⌀3x15 (for wood) | quantity: 24 hexagon nuts M6 | quantity: 16 cylinder…
- Pobrania
- 119
- Polubienia
- 40
- Ocena
- 5
P
PrintablesH3dSprint
Holder for a bike lock - e.g. for Appollo bike lock
The holder is suitable for a seat post with Ø26,8mm and for a bike lock with Ø38mm. The holder is built up by two printed parts out of PETG. To mount the holder to the seat post, use cylinder screws M4x16 (5x) and hexagon nuts M4 (5x).
- Pobrania
- 117
- Polubienia
- 42
- Ocena
- 5
P
PrintablesH3dSprint
Cap for saxophone mouthpiece
The cap is printed with flexible hard filament.
- Pobrania
- 108
- Polubienia
- 11
- Ocena
- 0
P
PrintablesH3dSprint
Strainer for roof gutter RG150
Part is printed with PETG and do not need supports.
- Pobrania
- 104
- Polubienia
- 27
- Ocena
- 5
P
PrintablesH3dSprint
Fastener - suitable for IKEA Samla box 45 liter
The fastener is suitable for an IKEA Samla box with 45 liter and can be used with or without a sealing. If used for a filament box: For the sealing I recommend to use a foam rubber which is bonded to the box. The thickness of the pressed…
- Pobrania
- 103
- Polubienia
- 25
- Ocena
- 4,5
P
PrintablesH3dSprint
Y-Piece to enable a bypass to feed filament without or through a second PTFE-Pipe
Print instruction: material: PETG supports: recommended (see attached picture) layer height: 0,2mm nozzle diameter: 0,4mm brim: recommended enclosure: not required
- Pobrania
- 97
- Polubienia
- 20
- Ocena
- 5
P
PrintablesH3dSprint
Mixer ⌀65mm for rod with thread M8
Part is printed with PETG and do not need supports. Two versions are available: upwards / downwards If you are searching for a smaller mixer, follow the link: Mixer ⌀45mm for rod with thread M8 von H3dSprint | Kostenloses STL-Modell…
- Pobrania
- 94
- Polubienia
- 14
- Ocena
- 5
P
PrintablesH3dSprint
Small nozzle for vacuum cleaner (pipe: ⌀35,5 / nozzle: 10,4mm x 33,4mm)
The nozzle is suitable for vaccum cleaners with ⌀35,5mm (measured on inlet of the vacuum cleaner pipe) and is printed with PETG. Print instruction: Orientation: print upright Due to the height of 208mm, I recommend to add a support on the…
- Pobrania
- 93
- Polubienia
- 20
- Ocena
- 5
P
PrintablesH3dSprint
Pressure key (25,6x29,6 mm) replacement part for RITTO door bell
Pressure key is printed with ASA and need partial supports. After printing, the part was grinded and smoothed with aceton by spraying.
- Pobrania
- 88
- Polubienia
- 6
- Ocena
- 0
P
PrintablesH3dSprint
Mixer ⌀45mm for rod with thread M8
Part is printed with PETG and do not need supports.
- Pobrania
- 82
- Polubienia
- 15
- Ocena
- 0
P
PrintablesH3dSprint
Bottle holder with an image for bottle up to diameter 90mm
The bottle holder is designed for applications where a bottle holder should be swinged away if it is not in use. Design goals suitable for bottles with a diameter of 90mm foldable to save space if not in use shall not clatter if folded…
- Pobrania
- 82
- Polubienia
- 13
- Ocena
- 0
P
PrintablesH3dSprint
Holder suitable for a SpeedCoach
Print instruction: material: PETG or ASA supports: partial required layer height: 0,25mm or 0,32mm nozzle diameter: 0,4mm or 0,6mm brim: not required enclosure: not required
- Pobrania
- 80
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Tray extender for music stand
To avoid down hanging music sheets, print 2 of the extenders and snap on to your music stand.
- Pobrania
- 78
- Polubienia
- 24
- Ocena
- 4,5
P
PrintablesH3dSprint
Bend protection for USB cable - e.g. Samsung
Part is printed with Ninjaflex shore hardness 85A and do not need supports. To avoid stringing, I recommend to print parts separately. To ensure a straight seat, the bend protection is built up by 2 parts. Inner part (1) support the cable…
- Pobrania
- 77
- Polubienia
- 14
- Ocena
- 0
P
PrintablesH3dSprint
Adapter for cordless screwdriver - suitable for Makita
General description The adapter is mainly created for use with a peristaltic pump , where I didnt want to press the power button of the screwdriver for a while to keep constant speed. Using the adapter allows to adjust speed to your needs…
- Pobrania
- 73
- Polubienia
- 38
- Ocena
- 0
P
PrintablesH3dSprint
Wet filament in comparison to dry filament - TPU (flexible)
I bought Extrudr semisoft filament and started the first print after putting the filament from original package into my filament box. The result of the printed part was worse. I repeated the same print with a different flexible filament…
- Pobrania
- 70
- Polubienia
- 22
- Ocena
- 5
P
PrintablesH3dSprint
Wall holder for Hörmann remote control (38 x 15 mm)
The wall holder is suitable for Hörmann HS… Series. If you want to use it for the small size of the HS types, reduce the height of the holder by cutting out material in your slicer. Holder is printed with PLA and need partial supports.
- Pobrania
- 68
- Polubienia
- 5
- Ocena
- 0
P
PrintablesH3dSprint
Hex nut M22×1.5, e.g. for securing a lampshade
After the original nut broke, I designed this hex nut as a replacement part.
- Pobrania
- 67
- Polubienia
- 6
- Ocena
- 0
P
PrintablesH3dSprint
Mixer ⌀90mm for rod with thread M8
Part is printed with PETG and do not need supports. If you are searching for other sizes, follow the links below: Mixer ⌀45mm for rod with thread M8 von H3dSprint | Kostenloses STL-Modell herunterladen | Printables.com Mixer ⌀65mm for rod…
- Pobrania
- 67
- Polubienia
- 10
- Ocena
- 5
P
PrintablesH3dSprint
Actuator rod - suitable for Geberit Twinline
Print instruction: material: PETG or similar supports: required layer height: 0,2mm or 0,32mm nozzle diameter: 0,4mm or 0,6mm brim: not required enclosure: not required
- Pobrania
- 66
- Polubienia
- 2
- Ocena
- 0
P
PrintablesH3dSprint
Measuring spoon with a 1 ml capacity, e.g. for mixing 2-component adhesives.
Print instruction: slicer: split .stl into parts to get text material: PETG supports: no layer height: 0,25mm nozzle diameter: 0,4mm or 0,6mm brim: not required enclosure: not required
- Pobrania
- 64
- Polubienia
- 7
- Ocena
- 5
P
PrintablesH3dSprint
Hand grip for Fiskars branch saw of tree pruner UPX86
The hand grip is printed with ASA and is smoothed with aceton by spraying. I have used spraying to finish only outer surface of the hand grip, because warping is lower if only partial surfaces are smoothed. The hand grip works also fine…
- Pobrania
- 63
- Polubienia
- 18
- Ocena
- 0
P
PrintablesH3dSprint
Protection cap for wooden beam 90x90 mm
The protection cap is printed with PETG and need supports. To use the cap for other dimensions, scale the cap in the slicer according your needs.
- Pobrania
- 62
- Polubienia
- 16
- Ocena
- 0
P
PrintablesH3dSprint
Tool to cut sheetmetal by a defined thickness - suitable for Makita grinder diameter 125mm
Parts are printed with ASA and need partially supports. Assembly instruction: Connect the plate to the angle grinder using cylinder screws M8x15 (2x) and washers for M8 (2x). Add hexagon nuts M4 (2x) to the plate Assemble torque support…
- Pobrania
- 61
- Polubienia
- 18
- Ocena
- 0
P
PrintablesH3dSprint
Clip for Bestway frame pool to fix tarpaulin
The clip is printed with PETG and do not need supports. Mount the clip as shown on the picture.
- Pobrania
- 56
- Polubienia
- 11
- Ocena
- 0
P
PrintablesH3dSprint
Scraper bar for snow shovel
The scraper bar is printed with PETG and do not need supports. Print instruction To avoid warping it is important to ensure a good bed adhesion and I recommend to print the parts in an enclosure. Assembly instruction add scraper bar to…
- Pobrania
- 55
- Polubienia
- 10
- Ocena
- 0
P
PrintablesH3dSprint
Tool to replace filter of Drufi DFR
To use the printed tool, I recommend a pipe or a shaft with a diameter of 16mm out of stainless steel or any other metal material. Part list: printed ring | quantity: 1 printed fixing plate | quantity: 2 pipe or rod ⌀16mm | length: ≥200mm…
- Pobrania
- 55
- Polubienia
- 5
- Ocena
- 0
P
PrintablesH3dSprint
Lamp shade for outdoor lamp (M62x1,5)
The lamp shade is printed with translucent PETG filament and contain a labyrinth seal instead of a rubber seal. Print instruction: supports: NO layer height: 0,2mm (recommended) nozzle diameter: 0,4mm or 0,6mm brim: YES (recommended to…
- Pobrania
- 53
- Polubienia
- 22
- Ocena
- 0
P
PrintablesH3dSprint
Test cube with fuzzy skin on the side surfaces.
The cubes shown were printed using Extrudr Flax filament. The first cube from the left uses the Prusa Slicer’s default Fuzzy Skin setting of 0.8/0.3. The second cube uses Fuzzy Skin values of 0.4/0.1. The third cube was printed without…
- Pobrania
- 47
- Polubienia
- 1
- Ocena
- 4
P
PrintablesH3dSprint
Sealing cap for bore ⌀35mm (minimal depth: 17mm)
The sealing cap is printed with flexible filament (Ninjaflex 85A) and do not need support. First sealing ring is smaller for easier mounting. To adjust to other diameters, scale in Prusa Slicer to your needs.
- Pobrania
- 45
- Polubienia
- 6
- Ocena
- 0
P
PrintablesH3dSprint
Soft-head hammer cap (inner cap size 26,5mm x 27,4mm)
The soft-head hammer cap is printed with PETG. Dependent to your use case, choose the suitable material for the cap. To adjust to your hammer, scale the cap in your slicer.
- Pobrania
- 45
- Polubienia
- 9
- Ocena
- 5
P
PrintablesH3dSprint
Clip to fix a additional pipe to guide filament - suitable for Prusa XL
Print instruction: material: PETG supports: no layer height: 0,2mm nozzle diameter: 0,4mm brim: recommmended - width: 6mm enclosure: not required
- Pobrania
- 40
- Polubienia
- 11
- Ocena
- 0
P
PrintablesH3dSprint
Primer bulb - suitable for Briggs&Stratton engine
The primer bulb design do not need support and the head of the bulb is a flat surface to avoid smearing. Print settings for Ninjaflex (85A): copied Prusa Generic-Flex profile and adjusted extrusion multiplier to 1,3 printed on smooth PEI…
- Pobrania
- 40
- Polubienia
- 5
- Ocena
- 0
P
PrintablesH3dSprint
Gearshift pattern - 6 speed
Gearshift pattern fit to gear lever knob which is e.g. suitable for Fendt. Printed in two steps. At first the text is printed with white filament and afterwards the rest is printed in black. Place the .stl file on the bed between the…
- Pobrania
- 38
- Polubienia
- 9
- Ocena
- 5
P
PrintablesH3dSprint
Insert for Gedore toolbox
The insert is printed with PLA and need supports which can be left to use the insert in the toolbox. To print the insert on my Prusa MK3S+ the insert is splitted into two parts and jointed with dovetail connections.
- Pobrania
- 38
- Polubienia
- 17
- Ocena
- 0
P
PrintablesH3dSprint
Clip repair for Christmas candles
The clip is reinforced to avoid the joint get broken again. Print instruction: Material: PETG recommended Supports: partial required - organic support recommended Enclosure: not required The clip is suitable for e.g. LED Christmas candles…
- Pobrania
- 38
- Polubienia
- 9
- Ocena
- 0
P
PrintablesH3dSprint
Adapter for rear reflector - kid bike (24")
The adapter is printed in PETG and could be fixed with cylinder screws M5 to bicycle frame. To assemble the reflector use also screws M5. Part is printed on the plane surface. The only support which is needed is the horizontal surface of…
- Pobrania
- 37
- Polubienia
- 7
- Ocena
- 0
P
PrintablesH3dSprint
Key for door closer
Especially if you are visited by a toddler, this key is helpful to unlock a door with a door closer. Due to the small size, the key can be placed on top of the door frame and is available if you have to unlock the door. The key is printed…
- Pobrania
- 37
- Polubienia
- 7
- Ocena
- 5
P
PrintablesH3dSprint
Adapter to connect a pipe ⌀32mm and a corrugated tube ⌀42,5mm
The parts are printed with PETG and do not need supports. To connect both parts, use 2 rod ⌀2mm with rectangular bended ends.
- Pobrania
- 37
- Polubienia
- 3
- Ocena
- 0
P
PrintablesH3dSprint
Wheels with axle for floor nozzle of vacuum cleaner - suitable for e.g. Siemens
Part is printed with PETG and need partial support. Part list: wheel | quantity: 2 hose 5x1 | length: 90mm threaded bar M3 | length: 108mm hexagon nuts M3 | quantity: 4 washer for M3 e.g. ISO 7093 | quantity: 2 Print instruction:…
- Pobrania
- 36
- Polubienia
- 2
- Ocena
- 0
P
PrintablesH3dSprint
Limit stop for loppers - spare part suitable for Gardena
To assemble the limit stop use following fixing elements: cylinder screw M3x20 | quantity: 2 hexagon nut M3 | quantity: 2
- Pobrania
- 35
- Polubienia
- 10
- Ocena
- 5
P
PrintablesH3dSprint
Mixing dish for small amounts of 2-component adhesives or epoxy resin.
I looked at several mixing dishes, but they lacked details like stability, grip, and a pour spout. I also wanted to use as little filament as possible, since I typically use the dish only once for 2-component adhesives. The mixing stick…
- Pobrania
- 35
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Clip for neon lamp - replacement part
Pull hook is printed with PETG and need partial supports.
- Pobrania
- 35
- Polubienia
- 2
- Ocena
- 0
P
PrintablesH3dSprint
Coaster for table leg to protect wooden leg against wetness
The coaster contain a groove and openings on the side wall to drain water if e.g. rain run between the table leg and the coaster. Part is printed with PETG and do not need supports. If your table leg have different dimensions, adjust the…
- Pobrania
- 33
- Polubienia
- 5
- Ocena
- 0
P
PrintablesH3dSprint
Corner angle to build up a tentative enclosure for printing or varnishing
Corner angle is printed out of PETG and do not need supports. To connect the angle corner with the cardboard, I recommend to make a cut to the cardboard and flatten down crinkles for easier mounting.
- Pobrania
- 33
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Wet filament in comparison to dry filament - PMMA
To print parts which looks like glass, I made some tests with PMMA (Mitsubishi 3Diakon - transparent - 1,75mm). I bought the sample filament some month ago and stored it in the original package. Last week I opened the package and put the…
- Pobrania
- 32
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Repair adapter for safety glasses - Hoffmann Group / Holex
The part is printed with PETG. Print instruction: supports: YES | default setting recommended layer height: 0,2mm nozzle diameter: 0,4mm brim: YES (recommended to ensure good adhesion on the print bed) enclosure: NO Assembly instruction:…
- Pobrania
- 32
- Polubienia
- 5
- Ocena
- 0
P
PrintablesH3dSprint
Holder for vacuum cleaner accessories - suitable for Kärcher A2604
The holder is printed with PETG and do not need supports. Part list: holder | quantity: 1 counter plate | quantity: 1 countersunk screw ⌀4x40 (for wood) | quantity: 3 Print instruction: supports: NO layer height: 0,2mm or 0,3mm nozzle…
- Pobrania
- 32
- Polubienia
- 8
- Ocena
- 0
P
PrintablesH3dSprint
Hinge for Siemens freezer - spare part
Hinge is printed out of PETG and do not need supports. Assembly instruction: Remove the broken hinge from the flap to get a plain surface Allign the hing on the hatch Drill two bores with ⌀3,3mm and remove the burr Insert 2 hexagon nuts…
- Pobrania
- 31
- Polubienia
- 5
- Ocena
- 0
P
PrintablesH3dSprint
Sealing ring for watch - 38x0,8 - TPU shore hardness 85A
The O-ring is printed with Extrudr semisoft (shore hardness 85A) and do not need supports. For printing, I recommend to place the flat surface to the print bed. To replace the O-ring, you should slightly grease the O-ring e.g. with…
- Pobrania
- 29
- Polubienia
- 8
- Ocena
- 0
P
PrintablesH3dSprint
Depth stop for multi tool - depth 5mm
Part is printed with PETG and do not need supports. For the cutting disc which is shown on the picture, the depth is limited to 5mm. Assembly instruction: Add hexagon nuts M3 (2x) to clamp plate 1. Add hexagon nuts M3 (2x) and M4 (2x) to…
- Pobrania
- 29
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Prusa XL enclosure below 120 €
Since I couldn't find a printer housing for the Prusa XL that met my requirements, I designed my own enclosure. My requirements were: Cost-effective Minimal filament usage for printing the parts Free of shrinkage issues Free access to the…
- Pobrania
- 28
- Polubienia
- 18
- Ocena
- 0
P
PrintablesH3dSprint
Belt GT3 with 96 teeth
The belt is printed using Extrudr semisoft shore hardness 85A. For testing, the scale ring I designed can be used as the matching counterpart.
- Pobrania
- 27
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Holder for LED-lamp - Müller-Licht
The holder is printed with PETG and do not need supports. To avoid bending force at the holder and to simplify the handling, there are screws added from each side. Part list: holder | quantity: 4 countersunk screw ⌀4x70 (for wood) |…
- Pobrania
- 27
- Polubienia
- 7
- Ocena
- 0
P
PrintablesH3dSprint
Hook for attaching to a car seat headrest - suitable for ⌀ 14 mm
The hook is made from flexible filament, which prevents any risk of injury from the part. Print instruction: material: Flex Hard - any other material will work also layer height: 0,3mm nozzle: 0,6mm (0,4mm) support: no enclosure: not…
- Pobrania
- 25
- Polubienia
- 2
- Ocena
- 4
P
PrintablesH3dSprint
T-Slot nut M4 with TPU spring to fix parts e.g. to a workbench
The T-Slot nut is suitable for rails 30x30 and a width of 8mm. To ensure T-Slot nut is fixed also in vertical position, I have designed a TPU spring which is fixed to main body by a dovetail groove. I recommend to use a TPU with a low…
- Pobrania
- 24
- Polubienia
- 9
- Ocena
- 0
P
PrintablesH3dSprint
Adapter to adapt a stick to a snow shovel
The part is printed with PETG and need supports. The bore for the stick have a diameter of 28mm. To fix the adapter to the snow shovel, use hexagon nuts M5 (2x) and cylinder screws M5x15 (2x). For clamping the stick, use hexagon nuts M4…
- Pobrania
- 24
- Polubienia
- 6
- Ocena
- 0
P
PrintablesH3dSprint
Cleaning nozzle for a hose to clean deep bores
The cleaning nozzle is printed with PETG and do not need supports. To assemble the nozzle to the hose, I recommend to use some grease. If your hose have a different diameter or you have to adjust the diameter due to the stiffness of the…
- Pobrania
- 23
- Polubienia
- 5
- Ocena
- 0
P
PrintablesH3dSprint
Salt shaker for a can
To avoid contact to salt and to ensure an easy handling by strewing salt, I have designed this salt shaker. If you remove the perforated disc, you have a funnel to fill the salt into the can. Print instruction The salt shaker is printed…
- Pobrania
- 23
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Spare part for the handwheel of a Scheppach woodturning machine (shaft: Ø12mm)
To prevent the mount from breaking again, I increased the outer diameter to improve stability. Part list: spare part cylinder head screw M5x30 | quantity: 1 hexagon nut M5 | quantity: 1 Print instruction: material: PETG or similar…
- Pobrania
- 21
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Keyhole plate to cover slot hole 21,9x8,3
Part is printed with PETG and do not need supports. To adjust to your needs, scale part in your slicer.
- Pobrania
- 21
- Polubienia
- 2
- Ocena
- 0
P
PrintablesH3dSprint
Conductive filament - test sample
The resistance of the printed trace is quite high despite its large cross-section, and the white LED barely lights up—even though it's powered by a 9V battery. For printing, I recommend feeding the filament directly into the extruder…
- Pobrania
- 20
- Polubienia
- 3
- Ocena
- 0
P
PrintablesH3dSprint
fixing clamp for cable duct 15x15 and 30x15
Parts are printed with Extrudr semisoft shore hardness 85A and need partial support. To ensure support can be easy removed, I recommend to use organic support.
- Pobrania
- 20
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Nozzle to clean e.g. the drain pipe of a shower
Part is printed with PETG and is designed for an interface M8. I am using a polyurethan tube ⌀10 x ⌀6,5 where I add a thread M8 for the nozzle. I recommend to cut the thread step by step to avoid screw tap get stucked. Print instruction:…
- Pobrania
- 20
- Polubienia
- 2
- Ocena
- 0
P
PrintablesH3dSprint
label for spray bottle - suitable for IKEA TOMAT
Design do not need supports. To be able to create your own text, I have added a label without signs and text. Text can be added in slicer. Printing Material: PETG Add .stl to your slicer and place the label in an area of the print plate…
- Pobrania
- 20
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Replacement clip for Christmas candles
The clip is a full replacement of the original part. The clip is reinforced and improved with a metal pin as a joint. Part list: printed parts pin ø2mm x 16mm Print instruction: Material: PETG recommended Supports: partial required -…
- Pobrania
- 18
- Polubienia
- 2
- Ocena
- 0
P
PrintablesH3dSprint
Spacing washer - suitable for Sodastream Crystal
To avoid extensive replacement of the sealing of my Sodastream, I have designed a spacing washer to increase the sealing pressure. I have added different sizes of the spacing washer. I recommend to try at first the spacer with 0.4mm. If…
- Pobrania
- 18
- Polubienia
- 1
- Ocena
- 0
P
PrintablesH3dSprint
Spacer for cutting tool
There are two versions of the spacer to ensure cutting with protection shield. To adjust to your needs, you can modify the thickness in your slicer. To download cutting tool, follow link: Tool to cut sheetmetal by a defined thickness -…
- Pobrania
- 18
- Polubienia
- 8
- Ocena
- 0
P
PrintablesH3dSprint
Drawer side panel
The STL files each contain 4 parts to prevent the parts from detaching from the print bed due to the small contact area and the tall height. Print instruction material: PETG or similar supports: no layer height: 0,3mm nozzle diameter:…
- Pobrania
- 17
- Polubienia
- 4
- Ocena
- 0
P
PrintablesH3dSprint
Protective magnetic jaws for clamping – length 140 mm
The protective jaws are mirror-symmetrical and feature a positioning tab for alignment with the vise jaw. To ensure a flush fit with the top surface of the vise when clamping flat or small parts, the tab can be oriented either upward or…
- Pobrania
- 17
- Polubienia
- 3
- Ocena
- 0