Liczymy pasujące modele…
X gantry model I recreated of the Ender 3/pro/3v2/CR10 (v1) Holes are perfectly aligned, I then used this to design shrouds (like the MarsOrbiter, SaturnOrbiter and ApolloLander, of which I never received any complaints regarding mounting…
just another fan grill design easy to print, no print support. the large air gap between the fan blades and the grill allows little to no added turbulence noise from it. 10mm thick to match a 4020 fan thickness when used with a 4010 fan,…
120mm fan grill 6mm thick, with 4mm clearance between fan and grill. Compatible with regular self tapping screws like used on computers ------ Support me on Patreon ! https://patreon.com/squirrelf3d or buy me a coffee…
This is only possible thanks to all of my present and past patreon supporter. So a huge shout-out to them!!! ------ Full model is on my https://patreon.com/squirrelf3d - linear rail version - many supported hotend ( list here ) - some…
The hotend I bought was not an official creality one, not even sure creality makes that hotend. But can easily be found on amazon and aliexpress, just seemed like a better heatsink design. At the time of this writing I haven't tried it…
This is a humane mouse trap for catch and release, so as to not hurt the mouse and allow relocation. This is not really a leave and forget kinda a trap, but one to either help you catch a mouse as opposed to using a cardboard box. Or in…
This uses four m3x8 screws and a gt2 20teeth timing pulley with either 8mm or 5mm bore The front "lip" of the gt2 20t pulley will pop off easily with pliers make sure to keep pressing on the gt2 20t pulley while securing the screws. I…
Smart Orbiter v3.0 5015 duct! no print support! Also has a noise mod to change the noise profile of the orbiter fan (from mosquito to woosh) Fan noise mod does need print support, use tree support Added the Revo version STEP: printables…
You'll need four M5x12 and eight M3x6 for the linear rail block (M3x8 might work too, not sure) To install it, partially screw in the screw into the hex nut (use the stock ones) to lift the nut, and place the mount over the rail block…
80mm fan grill 6mm thick, with 4mm clearance between fan and grill. Compatible with regular self tapping screws like used on computers ------ Support me on Patreon ! https://patreon.com/squirrelf3d or buy me a coffee…
Reason this is the best phone ever: thinest phone, thinner than an apple iPad Pro 2024 model at only 3mm no battery required, just imagination Camera imprints directly into your memory in super high resolution silent mode 100% of the…
For one of the most common generic type of ADXL345, see picture (15mm screw hole distance and about 20x16mm PCB dimensions) Print the M3x4 or M3x6 model, once the print is done, set the bed to stay hot (don't let it cool too much or…
No print support needed! I know this is not the first model for this purpose, this one uses heat inserts (M3, 4mm long, 4.6mm or 5mm OD) Also added a bunch of additional mounting point (meant to use heat inserts M3, 4mm long, 4.6mm or 5mm…
Huge thanks to my Patrons and Printable's Club supporter without whom this would not exist. To support my work , the material, time testing, and refining it consider joining my Patreon (also has the ApolloLander shroud) or Printables'…
This is an old design of mine, nothing fancy, simple but they work well. v1 might interfere with cases that fit under the printer. v2 has the same rail shape, but has a vertical inner wall to avoid colliding with cases that go under the…
Box designed by Mriamsosmrt to which I added snapping tabs to box and lid to avoid accidental card spill.
This needs print support (to reduce additional noise turbulence by having the "grill" further away from the fan blades), I used hybrid trees with 0.2mm interface, and 80% line width on support which helps separate it. followed by a bit of…
I tried 120 clicks, but was too small and overkill, and the click tactile feedback wasn't strong enough to my taste. So picked 60 to match Klipper minute:second approach when using SCREWS_TILT_CALCULATE. These, fresh at least, have a nice…
No print support! https://www.phaetus.com/en-us/products/dxc-extruder The motor is not included as it's meant to be a drop in replacement for the Creality K1 extruder. Needs to be 12t gear (the common motor for Sherpa and Orbiter uses…
Easy to print, no print support Fan clip for 2510 fan M2.5x14 or M2.5x16 screws Fits v6 hotend and all derivative Not actually tested in practice regarding cooling capability, may want to consider installing it at a slightly lower point…
I regard this an as archive so there will be no further update, and no support for it Here for anyone wanting to give this a spin. Unlike my newer designs this requires very few screws and no heat inserts. My current dual 5015 model is…
FLYSHT-36 V2.0 has a bigger connector and tweaked things to avoid crushing resistors
For a ARRMA 40mmØ motor (62mm long) fan mount used in some remote controlled cars. dual 4010 and dual 4020 mount Print should not need any print support. PETG or better for the clip part, since I assume it's on a hot motor. Clip itself is…
This is an old model I made on thingiverse, reposting it here with a pneumatic M6 thread option for bowden Also included STEP file ------ Support me on Patreon so I can make more stuff! https://patreon.com/squirrelf3d or buy me a coffee…
Small design flaw in my original model new files are from march 28th 2025 requires a full reprint, outer shell is incompatible with original model (the wheel is unchanged) shell of the F634Z and F625Z version had another flaw, now fixed…
Uses M3 screws, that will screw in plastic to secure the ADXL to the mount Side with the rectangular dip is where the ADXL will mount. This was a request by one of my patrons, haven't tested it myself. edit: needed a little wider recessed…
I don't see the point of overhang test below 55degree as most printer should be able to do that. So directly testing 65 and 75 degree as a way to calibrate speeds and fan speed (or compare ducts variation, which I've been playing with on…
This is useful for hotend mounts that moves the hotend forward (like all of my designs for top mounted hotends, and likely many other), which usually lead to lost printable space, this gains 10mm back, for the full 235mm in Y But does…
No print support needed Screw and heat inserts are totally optional for the actual case and even screen , this can hold on it's own as is, just sliding the pieces together, and screen can just rest there (as long as there is no risk of it…
Assembly like IKEA should be figured out by yourself and considered cryptic. Have fun. Just gently hammer the feet in, tolerance are tight on purpose. The included hammer is 1/12th scale so might not be that useful to built this furniture…
This is what I assume was the intended dimensions. The accepted tolerance are large enough that when they add up can lead to over a mm difference between the CAD model and reality. some of the 40x40 extrusions on my printer have perfect…
For the Phaetus APUS 2 extruder Use M3x6 screws no print support ------ Support me on Patreon ! https://patreon.com/squirrelf3d or buy me a coffee https://ko-fi.com/squirrelf3d https://www.buymeacoffee.com/squirrelf
No print support needed! For MGN12H Consider this experimental for now. it works but there is room for improvement, keep an eye on the bltouch. No issue so far with PLA and part cooling fan on at 100% Screw length (might be some small…
updated Jan13: rev 3 should be safe to print and test. I printed rev 2 for the raspberry pi 3 and tft50 v2.0, and only one tiny fix was needed which is fixed in rev3 updated Jan12: there was a small area that needed shaving also tweaked…
WARNING: The ribbon cables on the fokoos odin are dangerous, and not meant to be use on motion area. The ends of the ribbon can easily "unglue" and overlap the next one, and the way they designed it can create a short (there should have…
This not meant for your stock belt, but in the event that you swap it to a fresh one. Print in PETG of better, no support needed Supports ender3pro / 3v2 / 3max 3max neo beds Disclaimer: After install there's a small chance that a belt…
Mellow FLY-UTOC-3 mount with M3 40x40 mounting pattern Uses hot threaded inserts M3x4mm(L)x 5 or 4.6mm (OD) STEP file if you want to add a cover or change the mount pattern ------ Support me on Patreon so I can make more stuff!…
I do not own an ender3 “v1” so I did not test this installed --- print it with many walls (6 or more) and high infill (40% or more) avoid PLA for this at least the piece touching the motor. the cover is fine in PLA You'll need either two…
Helps reduce the sound transmitted to the floor. You can also slide in a thin layer of foam/cheap yogamat on the inside. Print with soft TPU, I did only 2 walls and 5% gyroid infill 4 or 5 top bottom layers ------ Support me on Patreon !…
Remixed to add support for TridentSkirtLights For more info and the screen parts visit the project this was remixed from: Thick skirts for Voron Clicky Clack Fridge Door ----- This was a request by one of my long term patron, I didn't…
UPDATE: turns out there are no heat insert on the under side, so uploaded a newer adapter with “strong side mounts” (thank to the tweaks and change of print orientation ) you still have the option to drill in about 5mm without hitting…
This obviously won't be compatible with all mounting options, but might work with some. I'm currently testing the fan at 65~70% speed which with this mod has an unobtrusive whoosh noise and so far no clog (mostly tested TPU at 240~250C…
This was a request by some of my patrons Printable surface is likely reduced a bit to 200(X)x225(Y) Has be tested and working! This replaces the " X CARRIAGE_TOOLHEAD/ENG-XC1_b.stl " piece Everything else on the original Ender NG Post…
Raise your printer by 25/22/21mm, giving you a total of 35~31mm clearance, allowing larger fans to be installed below or even thicker printer boards. Needs M4x35 screws for the 25mm model Needs M4x30 screws for the 21mm model Needs M4x30…
This is a starting point to install linear rails on the Fokoos Odin5 F3 Compatible with Apollo Shroud and Apollo Mini - to use different aftermarket hotend and aftermarket direct drive extruder (or bowden setup) Uses heat inserts…
merged the bits, cleanup and added heatsink missing a few unimportant pins that got lost in the cleaning process, but their connector casing is there the standard octopus v1.1 is very close to this one, just a few different connectors in…
Parts are not oriented, I'll let you play with that in your slicer The larger piece does fit flat on 220x220 (longest length is 215mm) check original post for more info, and/or want to print it as a single piece…
2x M2x12 (bottom fan screws) 2x M2x8 (top fan screws) 2x M3x6 - flat head - accessories screws included with the hotend 2x M3x25 - hotend mount --- Want to support my work (STEP file available on patreon ) https://patreon.com/squirrelf3d
simple tray, with loose threads to easily screw in nozzles (M6) has a 8x3 and a 1x1 version ------ Support me on Patreon ! https://patreon.com/squirrelf3d or buy me a coffee https://ko-fi.com/squirrelf3d…
Lid made for a 92mm fan, specifically NF-A9x14, for the BTT M5p box that @Raziel_163191 designed This was request from one of my patrons Haven't tested it, but I made two models, one with the original thickness, and a second with a 5mm…
Use 4 heat inserts M3x4(L) x 4.6mm or 5mm (OD) where the corpus will mount included step file if you want to mod it a bit To raise your printer your can use the feet I made for it: here And you'll have to figure out cooling. I personally…
Made an adapter to fit extruders originally designed to mount on the Archetype shroud onto a sherpa mini mounting point So can also be used on the ApolloShroud (among others) In this case specifically, as seen on the render, the beta…
Adapter plate to fit an ApolloLander/ApolloMini to Enderwire and Switchwire (and other voron mount) You can get the Apollo on my Patreon (here) nozzle height is the same as stealthburner, so you can use a probe in the rear block, like an…
This is targeted at Ender3 series of printers and similar style, if using a different backplate than stock ender3/3pro/3v2, you can get those aftermarket, but I would then simply recommend you install a linear rails instead anyway, a much…
Bambu labeled one, does include all the Bambu clone and Phaetus Conch hotend that all use the Bambu printed mount I made (updated the case with a 3rd clasping screw) Dragon labeled one , applies to all the dragon style hotend, basically…
if you already have my belted z setup the top and bottom parts are the same, and the Z tensioner design is the same. I only made the red spring model (15x4mm generic cast spring from amazon/Ali) you can also use M4x16 instead of the…
This is a fully redesigned Y axis setup, meant for ender3pro, ender3v2, ender3max neo and similar 4040 profile Y extrusion, front and back end holes needs to be screw tapped for M5 (already the case on ender3v2, and confirmed to be the…
STL, notes and BOM is in the zip. Latest zip (September 8 2024) has linear rail version as well if you need a printed GT2 80t pulley click here One working and tested novelty here is a self tensioning system using a spring ( two specific…
To wszystkie aktualnie dostępne wyniki.
