Wyniki wyszukiwania: inch

Sortowanie

7885 modeli

P
PrintablesNautilus Forge

10 inch Rack 1U : 2 x 3.5 inch HDD - HOT SWAP !

⚒ No 3D printer? No time to source components? I just opened my new e-shop where you can buy physical, ready-to-use versions of my models! Designed with passion, printed and assembled with care ⚙. 📦 Shipping across the EU: 👉 Get it at…

Pobrania
4251
Polubienia
1066
Ocena
5
P
PrintablesCaptainAl

10 inch patch panel - 12 keystone module (1/2 U)

10-inch patch panel with 12 keystone module space. It's designed and created with OpenSCAD. The standard unit width is 44.45 mm, but to save some space for my very small network rack, I used 30 mm. You can change the module_count variable…

Pobrania
2822
Polubienia
250
Ocena
4,94
P
PrintablesMacNeill

Project Synthara - Generative Design FPV Drone Frame 3.5 Inch

Drones are a perfect playground for lightweight yet robust designs, and Synthara takes full advantage of cutting-edge generative design techniques. This 3D-printed drone frame is engineered for FPV enthusiasts looking for a balance…

Pobrania
2208
Polubienia
285
Ocena
5
P
Printableslufa

1/4 inch nuts and bolts for camera and tripod

1/4 zoll Schrauben und Muttern für Kameras und Stative. Die langen Schrauben können mit FreeCAD auf die benötigte Länge gekürzt werden.

Pobrania
2189
Polubienia
325
Ocena
4,64
P
PrintablesSovey

Saddle Ruler Square with marking holes for woodworking inches

This saddle t-square allows you to run lines parallel with an edge or perpendicular to it. It wraps around corners so you continue a line down an edge. The diamond shaped wholes keep your pencil centered to the line you're marking and…

Pobrania
1970
Polubienia
700
Ocena
5
P
Printablesjaln

Wahl Clipper Guides 12 and 16 (1.5 inch/37mm and 2 inch/50mm)

These are two Wahl clipper guides in 2 inch (50mm) and 1.5 inch (37mm) sizes. Should work with most 1.87 inch (47.6mm) max. wide Wahl style clipper blades. They are intended to be used with the clipper horizontally, on the side parallel…

Pobrania
1548
Polubienia
71
Ocena
5
P
PrintablesMartin
Pobrania
1156
Polubienia
170
Ocena
5
P
PrintablesJake Reeves

Perforated Sink Sponge Holder(s) - Single + Double Sided (15mm or 20mm Pinch)

After looking through a few different models online, I decided to create my own sink sponge holder and include some perforated holes that allow any water to easily drain away from the sponge - preventing moisture build-up . This was…

Pobrania
1070
Polubienia
131
Ocena
4,92

5.5-Inch Irrigation Ring With 0.25-Inch Tube Inlet

This is a 5.5-inch diameter irrigation ring designed to be used with 0.25-inch ID Tubing. Use a small ball valve to adjust the flow rate of the water through the ring. This works perfectly with my 2-Liter Soda Bottle To 0.25-Inch ID Tube…

Pobrania
975
Polubienia
200
Ocena
3
P
PrintablesMark Hall

Action Figure Stand for 8-12 inch models

A very simple stand, designed to not obscure your figure very much. Designed specifically for the figure pictured, but a very simple modification to the length of the strut would let you adapt it to any height. You'll need two braces per…

Pobrania
963
Polubienia
104
Ocena
5
P
PrintablesErik

Grinch Christmas ornament for MMU

I have added color to Vlado Turek 's Chrismas ornament in order to print it on my MK3S/MMU2 using PLA: “Yellow-Green”, Red, White, Yellow and Black.

Pobrania
954
Polubienia
181
Ocena
5
P
PrintablesDesignFlaw06

Grinch Christmas Ornament - MMU Remix

For those of us who can't paint, I remixed the ornament to a multi-color version. The 3MF is scaled up to be about a 3.5" ornament. I wanted a decent sized print to be shown with pride on our tree. As an added bonus, it makes it a little…

Pobrania
933
Polubienia
125
Ocena
5
P
PrintablesMSTVS

pinch valve powered by servo

Gary Wilson Jr. (named by GF) designed for Project “Cocktail mixer”: intended for 6 mm PTFE-Tube (might also work for smaller an up to 7-8 mm) -controlled by Micro Server 9g (SG90) printed in regular PLA Since I´m still working on a…

Pobrania
927
Polubienia
64
Ocena
5
P
PrintablesMiguel M.

5 inch vice soft jaws

These are vise soft jaws designed 5 inch vise There are 4 recesses in the back for 8x3mm magnets. You could use it without magnets or just the 2 on the front face but 4 holds it really nicely to the vise. I used C.A. glue to hold them in…

Pobrania
835
Polubienia
178
Ocena
5
P
PrintablesCoyotus

Vincha 2025 - Hair Band 2025

Vicha 2025, solo 14 gramos. Hair Band 2025, only 14 grams

Pobrania
762
Polubienia
40
Ocena
4,8
P
Printablesblide

Magnetic Socket Toolbox Organizer Half Inch 1\2"

Toolbox socket organizer for 1\2 inch sockets. The base is designed to accept a 10x3mm magnet as the base is printed at a .2 layer height. I printed all of these on a Creality CR-10S and placed a M25 pause between layer 16 and 17 in order…

Pobrania
666
Polubienia
191
Ocena
4,33
P
PrintablesJordi

Modular 10 inch rack 2U ITX case + storage mount

I designed this mini-itx case for the 10 inch rack i printed. The tray and the frontpanel are modular so you can remix the frontpanel without printing the whole model again. The case will fit a mini-itx motherboard and 3 2.5" ssds/hdds. I…

Pobrania
660
Polubienia
173
Ocena
5

Revolving cake stand for icing & serving 30cm (12 inch) capacity

Think I'm Awesome? ~ https://buymeacoffee.com/triplegworkshop 🏆 To celebrate the win I've added Low-Profile Legs that reduce the height 5cm! 🎆 It's Lazy Susan Mode!! 🍰 MMmmmmm This is purpose-built to make icing a breeze. Retaining rings…

Pobrania
636
Polubienia
465
Ocena
5
P
Printablesblide

Magnetic Socket Toolbox Organizer Three Eighth Inch 3\8"

Toolbox socket organizer for 3\8 inch sockets. The base is designed to accept a 10x3mm magnet as the base is printed at a .2 layer height. I printed all of these on a Creality CR-10S and placed a M25 pause between layer 16 and 17 in order…

Pobrania
619
Polubienia
163
Ocena
4,25
P
PrintablesJG

Simple Sanding Block (Corner and Curve remix, 1 inch wide)

This is a remix of Micke's Simple Sanding Block with Brainanator's cornering remix, plus my own remix of curved end. This will allow this sanding block to be useful for flat surfaces, inner corners and contours. I also shrink the model so…

Pobrania
615
Polubienia
70
Ocena
4,88
P
Printablestetralite

Tape Dispenser, 3-inch Blue or Shipping Tape

See my new improved version at https://www.prusaprinters.org/prints/74621-tape-dispenser-vers-td3-for-blue-and-shipping-tape A bench mountable tape dispenser for 3-inch wide blue painter's tape. Also works with 2-inch and 1-inch tape.…

Pobrania
573
Polubienia
144
Ocena
4,86
P
PrintablesGonper

No Touch Tool, retractable, door opener, key turning, pinch papers, push buttons...

I designed yet another No Touch Tool, did it retractable because if the areas that may touch contaminated surfaces are not enclosed somehow they may contaminate others like your pockets or your hands after it has been use. This tool is…

Pobrania
548
Polubienia
121
Ocena
3,5
P
PrintablesBaloo 3D

Capybara (carpincho) Scout woggle

Woggle neckerchief scarfring pasapañuelo for Scouts and CubScouts with Capybara (Carpincho)

Pobrania
498
Polubienia
45
Ocena
5
P
PrintablesObiWanJabroni

Duct Flange - Fits 120mm PC Fan Profile and 4 inch AC Duct

Flange that can be mounted onto a 120mm PC fan and then interface with a 4in" AC duct in order to vent heat and fumes outside. I am using thinkingalaud's original model for the flange that faces outside, but needed to remix their model to…

Pobrania
473
Polubienia
59
Ocena
5

7-Inch Irrigation Ring With 0.375-Inch Tube Inlet

This is a 7-inch diameter irrigation ring designed to be used with 0.375-inch ID Tubing. Use a small ball valve to adjust the flow rate of the water through the ring. This works perfectly with my 2-Liter Soda Bottle To 0.25-Inch ID Tube…

Pobrania
467
Polubienia
97
Ocena
5
P
Printablesuktricky

Dell Optiplex 5070 with Keystone Port for 10" inch rack

10" Rack tray to hold a Dell Optiplex 5070 (although other Optiplex models should fit) but also with an option to add a keystone jack (see my other models if you want to test print the same port to test). ** NOTE: These Rack components…

Pobrania
459
Polubienia
65
Ocena
4,6

1 inch female quick garden hose adapter / 1" adaptér s vnitřním závitem (pro zahradní hadici)

1 inch (D=32mm) female adapter for quick coupling garden hose to water tap. It can be printed without supports. O-ring is needed (Outer diameter = 16mm, inner diameter = 11mm, seal cross section = 2,5mm) and gasket between water tap and…

Pobrania
455
Polubienia
46
Ocena
0
P
PrintablesBram

5x 3.5 inch drive holder (Hard / Floppy Drive)

Mount for 5 3.5 inch drives I wanted to mount 5 Floppy drives on top of each other to experiment with playing MIDI files trough their stepper motors (See: Floppytron ). While searching for the mounting hole specs I found that these were…

Pobrania
416
Polubienia
53
Ocena
5
P
PrintablesCaptainAl

10inch 1U Raspberry Pi with SSD 2.5" rack mount (3 raspberry pi modules and 3 SSD)

Simple and helpful 1U Raspberry Pi with SSD 2.5" rackmount for 10inch network cabinets. It supports 3 Raspberry Pis. How to print: Print with 0.30mm layer height and 70% gyroid infill. Make sure your print is in PETG , ASA , or…

Pobrania
415
Polubienia
56
Ocena
4
P
PrintablesStrandedOrg

Small Mitre / Miter Box (1 inch / 26mm)

Small mitre box with a 1 inch / 26 millimeter channel for 45 and 90 degree cuts.

Pobrania
384
Polubienia
38
Ocena
5
P
Printablesstegi

Playmobil castle winch clip (part 3060354)

Replacement part for an old playmobil castle draw bridge winch. Playmobil part number is 3060354. Prints fast and easy, I used PETG for a litte flexibility. Other filament should work as well, though. --- Ersatzteil für die Zugbrücke der…

Pobrania
334
Polubienia
28
Ocena
5
P
PrintablesDan Waldron

120mm fan to 3 inch duct

Adapter duct to attach a 120mm fan to 3 inch duct. Made this to use dual 120mm fans on my simrig for movement simulation.

Pobrania
316
Polubienia
36
Ocena
5

Honeycomb Micro-Mesh 2-Inch x 2-Inch Sanding Pad Rack

I turn a lot of pens and use Micro-Mesh sanding pads to polish them when finished. I wanted a nice rack to hold the pads, and I think I went a little overboard with my design. This rack is fully skeletonized with a honeycomb pattern to…

Pobrania
273
Polubienia
89
Ocena
5
P
PrintablesFightTheFoo

Magnetic 4 inch Dust Collector Fitting

These fittings have embedded magnets to make connecting and disconnecting flexible dust collection hoses quick and easy. Attach one to each woodworking tool and one to the dust collector. Design was optimized to use the D83 magnets from…

Pobrania
263
Polubienia
81
Ocena
0
P
PrintablesLuckyMenace

1/2 inch / 13mm Irrigation Tube End Plug

Barbed end plug for run of 13mm irrigation tube / pipe - insert past the barb to stop water flow. Ensure you flip the STL file if using this - otherwise import the 3MF as this is the correct way around.

Pobrania
253
Polubienia
34
Ocena
5
P
PrintablesIan Foulds

Replacement Platypus Hose Clamp (Pinch Valve)

We had a hose clamp break on a Platypus water filter. I had one on another filter (black one) to work from, so I designed a replacement to match the original (white one). The textured part was add using paint on fuzzy skin. You can…

Pobrania
248
Polubienia
50
Ocena
5
P
PrintablesBrad Grier

Laptop Stand - Macbook Pro (Early 2011 - 13 inch)

Simple angled laptop stand for my Macbook Pro. Wanted a sharper angle to take up less deskroom. Will likely support other laptops -- the gap between vertical supports is 17mm. Inspired by this design but rebuilt in Tinkercad. I wanted to…

Pobrania
236
Polubienia
23
Ocena
5
P
Printables3DJG

Adaptable tray for telescope tripod (diameter 1.5 - 1.75 - 2 inch and 40mm)

Adaptable tray for telescope, for 1.75 and 2 inch tripods, with different inclinations and optional holders for tablets. (See also: https://www.printables.com/model/1040019-frame-for-models-of-telescope-trays ) After making several models…

Pobrania
213
Polubienia
36
Ocena
5
P
PrintablesMartin

New 360 Degrees Protractor centimetre (cm) And Inch

Type Protractor Size: 150 x 150 x 1.50mm 360 Degrees Protractor 0 to 9 centimetre (cm) And 0 to 3 Inch

Pobrania
210
Polubienia
26
Ocena
5
P
Printablesdrew.brashler

19.5 Inch Rack Ears (1U, 2U, 3U, 4U)

Printable rack ears with #10-32 tapped holes for 1U, 2U, 3U and 4U sizes to mount rack gear together outside of an enclosure. Also includes files for 1U, 2U and 3U with a leg to lift up the front of the piece of gear. I have a lot of…

Pobrania
190
Polubienia
47
Ocena
5
P
PrintablesAureusKhan

IKEA Linnmon Leg Mount for 1.5 inch PVC Pipe

This leg mount is designed to allow you to use 1.5 inch PVC pipe as legs for an IKEA Linnmon tabletop. I have also made matching feet for the PVC pipe that can be found here . Buy me a coffee :) - AureusKhan.com Random text for search…

Pobrania
164
Polubienia
35
Ocena
0
P
PrintablesAK3D

Stand turing smart screen 3.5-inch

This 3.5-inch monitor stand features an arm that securely attaches to the base of the main monitor. It offers adjustable depth and tilt, allowing you to position it as desired for optimal viewing. Link to my main monitor Link to my…

Pobrania
159
Polubienia
21
Ocena
0
P
PrintablesMiguel M.

Vise soft jaws 3 1/2 inch

3 ½ inch vise sofy jaws. You can glue 8x3mm magnet in the back if desired. (recommended) I use CA glue for my magnets. Enjoy!

Pobrania
153
Polubienia
37
Ocena
5

Inch threads up to 1" for freecad

I needed several inch threads for building waterpipe adapters in Freecad. They should be printed in PETG. The tools in the Fastener workbench did not have the correct pitches and tolerances. Here are some substraction bodies with a…

Pobrania
140
Polubienia
7
Ocena
0
P
Printablesseba

Prusa Mini Display 3.2 Inch LCD Back Cover with Air Vent

Screen back cover for 3.2. Prusa Mini display with air vent. Not sure if is needed, but I like it.

Pobrania
140
Polubienia
10
Ocena
3,67
P
Printablesdsorm

10 inch rack power strip mount (4-socket)

A mount for generic OEM 4-socket power strip for 10 inch mini rack. Might be compatible with different styles of power strips as well. A lot cheaper than buying PDUs, which are overkill for homelab usage. Recommended print settings:…

Pobrania
137
Polubienia
24
Ocena
0
P
PrintablesStougaard print

Edge Router X SFP 10 inch rack mount

Have create this mount to hold the Edge router X SFP with psu in the back to mount in a 10 inch rack. there is a clamp with that needs 2 screws in 3x10mm to mount the edgerouter X SFP securely so it doesn't move around when plugging and…

Pobrania
136
Polubienia
18
Ocena
0
P
Printablesasphaltbuffet

Inchworm Automaton - Alternative Knob

The available crank for the automaton often fell off or was difficult to spin well. It also broke once when handled roughly. I created this to be a little easier to print and eliminate smaller aspects that can break. There are two…

Pobrania
133
Polubienia
8
Ocena
0
P
PrintablesVenture_3D

1.5 inch Schedule 10 Cutout Template For 3-1 Merge

Print in PETG or PLA Different sizes included for different Schedule 10 manufacturer OD's Works well for fabrication of Manifolds or other 3 to 1 intersecting schedule 10 components Use 3D printed template to slide on pipe, and mark for…

Pobrania
125
Polubienia
9
Ocena
0
P
PrintablesSrayes

2 Inch Netcup for Hydroponics

2inch Net cup for Hydroponics systems, non-stackable, print as needed. RECOMMEND PRINTING WITH PAINT ON SUPPORTS FOR LIP ONLY For use with Rockwool, not tested with clay.

Pobrania
121
Polubienia
16
Ocena
0
P
Printablesron

airsoft specna arms handguard M4 10.7 inches

its a handguard for an M4 style airsoft gun. Based around the specna arms design. it takes 9 hours on a 15% infill on an elegoo printer.

Pobrania
116
Polubienia
23
Ocena
0
P
PrintablesIsaac Howard

4 inch inline fan duct Cradle

4 inch inline duct fan cradle. For the AC Infinity Raxial fan. Screw holes for #6 pan head screws.

Pobrania
111
Polubienia
20
Ocena
0
P
PrintablesPhil Caruso

Sink / Tub Strainer 40 mm (1.5 inch)

I created this Sink / Tub Strainer for 40 mm (1.5 inch) drains to prevent large objects (like screws) from going down the drain in my utility room sink. Before long, I realized that it was also the perfect addition to my bathroom tub.…

Pobrania
106
Polubienia
13
Ocena
5
P
PrintablesSteve H

13 inch laptop stand @ 40 degrees

laptop stand at 40 degrees for small 13 inch laptops

Pobrania
102
Polubienia
15
Ocena
5
P
PrintablesMichal

Winch for RES starts

Naviják na gumicuk pro starty modelářských letadel Nápad na návrh navijáku vznikl pro potřeby modelářského kroužku, kdy jsme v době koronavirového ohrožení měli zákaz se pravidelně scházet. Dětem, navštěvujícím modelářský kroužek, jsme…

Pobrania
97
Polubienia
23
Ocena
0

Small Mecanum Wheel - 3/8 inch Hex bore for FRC

Ultra lightweight and some of the smallest mechanums available. Print in PETG.Ream all the roller shaft holes with an 1/8inch drill bit and hand drill. Ream the two screw holes with a 3mm bit. Ream all the roller holes with a 3.5mm bit.…

Pobrania
96
Polubienia
15
Ocena
0
P
PrintablesJacob Desforges

5 Inch Gothic Fence Post Cap

One of my fence post caps was missing when I moved into my house, and another took some damage during a DIY tree trimming incident. I couldn't find any replacements with the similar 1" by 1" flat portion on top rather than a point. It's…

Pobrania
96
Polubienia
27
Ocena
0
P
PrintablesCity

10-24 Nut cropped to fit 1/8 inch slots

I liked SmilingImpact's 10-24 bolt and nut design but needed a nut short enough to fit 1/8 inch (roughly 3.5mm) nut slots. This nut remix is made to be 3mm tall so it fits easily into slotted parts. From testing, 0.1mm layer height is…

Pobrania
96
Polubienia
4
Ocena
5
P
Printablesjowings

Trex Decking 1/2n Inch Overhang Tool - Without Facia Installed

Much like my first iteration of this product, this tool allows you to have a perfect ½" overhang on your picture frame trex deck boards. This tool differs from the original in that you can lay your picture frame boards without first…

Pobrania
94
Polubienia
12
Ocena
0

1,5 to 1 inch quick hose adapter / 1,5" adaptér s vnitřním závitem pro 1" rychlospojku

The 45-degree adapter is used for quick connection of a garden pump with a 1.5 inch water output to a 1 inch quick coupling of the G.F. BIG system. The union nut (1,5 inch BSP thread - 44,845 / 47,803 mm) allows you to set the quick…

Pobrania
93
Polubienia
10
Ocena
5
P
PrintablesOnelostcause

2 inch Modular Hitch Cover with Embedded Nuts

This is a remix of the Modular Trailer Hitch Cover by rkxone on Thingiverse. I've added an additional set of faceplate mounting holes for more options when designing faceplates. The m3 nuts are also embedded in the print. Stop the print…

Pobrania
92
Polubienia
18
Ocena
0
P
PrintablesChris Inguelph

Blast Gate for 4 inch 100mm sewer pipe

I use this for my dust collection system. I have used one for several month and found it works great. Four ¼ bolts needed, I used hot glue for lock tight on hinge bolt and to seal the pipes. Hot glue can be removed with alcohol. New slide…

Pobrania
91
Polubienia
22
Ocena
0
P
PrintablesMartin

Finder Tool with 0 - 180 Degrees Angle mm & inch & cm

Finder Tool with 0 - 180 Degrees Angle Set Square 200mm & 8inch or Set Square 20cm & 8inch or Set Square 20cm Protractor Angle Ruler 180 Allow Screw: 1 x Nut M5 1 x Cap Head M5X20mm Filament: PLA, PETG, ASA & ABS Thank you ;-)

Pobrania
90
Polubienia
16
Ocena
0
P
PrintablesMariam Matta

XL 90mm/3.5 inch Bias tape maker (for sewing, making double fold straps)

Too much of sewing is pinning and measuring and I get bored easily! I got tired of making double fold straps so I made a giant bias tape maker instead. This is for 90mm/3.5 inch wide fabric strips. This was made using the customizer by…

Pobrania
87
Polubienia
36
Ocena
5
P
PrintablesAureusKhan

Foot for 1.5 inch PVC Pipe Table Leg

This foot is designed to allow you to use 1.5 inch PVC pipe as legs for any project without scratching floors. It was specifically designed for PVC pipe legs for the IKEA Linnmon tabletop, but it can be used to add a foot to any 1.5 inch…

Pobrania
83
Polubienia
15
Ocena
0
P
Printablesbsprange

Bissel Vacuum Adapter for D shaped nozzel to 32mm or 1 1/4 inch

I was frustrated with not being able to use standard vacuum attachments with my Bissel vacuum since it has a proprietary ‘D’ shaped nozzel. This adapter changes the nozzel to a standard household vacuum nozzel of 32mm or 1 ¼". The…

Pobrania
83
Polubienia
5
Ocena
0

1 inch male adapter to 1 inch garden system G.F. BIG quick coupler

EN: Adapter is used to connect the Quick Coupling of the Garden System G.F. BIG s.r.l. (Italy) to the standard 1-inch thread of the Garden Pump. I used Teflon tape to seal the thread and a 22.5 x 2.5 mm rubber O-ring for the quick…

Pobrania
83
Polubienia
18
Ocena
0
P
PrintablesThe Mapster

Shorter version (2 inch vs 4 inch)

Cut down to 2 inch tall vs the 4 inch original.

Pobrania
81
Polubienia
9
Ocena
5
P
Printablesbene

Belt's buckle (1.4inch remix)

Buckle for 36mm/1.4inch width belt. Print Settings Printer Brand Prusa Printer MINIIS Resolution .15 mm Infill 100% Filament Prusament PLA Recycled Build Plate Textured steel sheet Added paint-on fuzzy skin to imitate the feeling of the…

Pobrania
78
Polubienia
16
Ocena
0
P
Printablesgsatelite

GoPro mount for TBS Source One V5 5inch

GoPro mount for TBS Source One V5 5inch. Updated & tested! Good for PLA

Pobrania
73
Polubienia
5
Ocena
0
P
PrintablesBedLevelBoss

Flashcard__Holder (5X7 inch & 3X5 inch)

Welcome, and thank you for choosing my model. I will provide some context for this model. This practical 3D-printed flashcard holder is ideal for neatly organizing your study cards and presenting them in a clear overview. The design is…

Pobrania
68
Polubienia
39
Ocena
0
P
Printablesquebecprinter

2 inch scraper holder

This is a simple wall mount for 2 inch scrapers. I designed it to fit my scraper but it will work with other brands as well. The holder has a screw hole for easy mounting. I recommend printing it in the orientation it is supposed to be…

Pobrania
65
Polubienia
4
Ocena
0
P
PrintablesMartin

New 180 Semi Circular Protractor Inch

Transparent 180 degree 1 to 5 inch Type: Protractor Size: 150 x 92 x 1.50mm Filament: PLA & PETG Thank you ;-)

Pobrania
64
Polubienia
8
Ocena
4
P
PrintablesSot Kon

Grinch Christmas Ornament

Grinch Christmas Ornament Added strings and made the Grinch different type of ornament Be sure that you have arachne on in your slicer Keep the speed in normal range 60 to 100 mm/s No supports are needed If you have multicolor printer in…

Pobrania
63
Polubienia
9
Ocena
0
P
PrintablesHenry Levesque

Quarter Inch Quick Connect Fitting Retaining Clip

Quarter Inch Quick Connect Fitting Retaining Clip

Pobrania
62
Polubienia
8
Ocena
5
P
Printablescookiecrook

Wall mount for aluminum blast gate, 4 inch gates (~100mm)

I recently replaced my plastic 4" (~100mm) blast gates with cast aluminum gates from Powertec , and I needed wall mounts for a few. The blast gates I used are just under 11mm in the slot, and the 3 bolt holes are 77.5mm apart. Included…

Pobrania
61
Polubienia
23
Ocena
5
P
PrintablesDanAndersen

Kopp Powerversal PDU - 19 Inch Rackmount ears - Steckdosenleiste Serverrack

Even though the Kopp Powerversal power distribution are completely made of plastic (don't get fooled by the aluminum look), they are made extremely well from the electrical standpoint. Additionally, the power sockets have the right angle.…

Pobrania
58
Polubienia
21
Ocena
0
P
PrintablesJimleeQ

2.8 inch Pimoroni Pico display case - with 4 buttons

I bought one of these 2.8inch LCD displays ( https://shop.pimoroni.com/products/pico-display-pack-2-8?variant=42047194005587 ) to use with a Pico W as I wanted a small, but capable bit of screen space to show some stats etc. It just plugs…

Pobrania
56
Polubienia
4
Ocena
0
P
PrintablesFergyMcFerguson

4" inch OD dust collector port to 2.5" shop vac

This adapter is designed to fit the outside diameter of the 4" dust collection port on wood working tools and reduce it to the ID of the 2.5" shop vac / dust separator hose. Many online adapters and store bought adapters that I've tried…

Pobrania
53
Polubienia
6
Ocena
0
P
PrintablesCreativus

GoPro Mount for a 3/4inch or 19mm tube with end cap and M4 nut (Remix of Go-Pro ring mount)

Remix with an end cap, 3/4in or 19mm hole for a tube or pipe, and hole to place an M4 hex nut. I suggest printing it with 100 % infill for good strength. Feel free to like, download and follow. If you want check my other models. Happy…

Pobrania
51
Polubienia
7
Ocena
0

Amateur Radio License Frame for FCC Print and cut size (5 1/4 x 6 1/2 inches)

Openframe.stl is frame only (~2 hrs to print). You just cut cardboard back the outersize of frame and glue to frame. You can then paste your license print to the cardboard and there you have it using minimal filament (pla) hamlicense…

Pobrania
51
Polubienia
8
Ocena
0
P
PrintablesFlat Badger

10-inch panel for GL.iNet Comet KVM

This is a 10" rack panel designed to hold a GL.iNET Comet remote KVM. There are two keystone jack sockets to bring the power and network connections to the front of the panel. This model does require support on the tray that holds the…

Pobrania
49
Polubienia
8
Ocena
0
P
PrintablesRagingRoosevelt

Sewing Seam Allowance Tracing Disks (inches and mm)

Use these tools to add seam allowance to your sewing pattern: either increase the existing seam allowance or add more seam allowance. Sizes Available is both a set of metric and imperial tools. Metric tools range from 5mm to 25mm in 5mm…

Pobrania
49
Polubienia
17
Ocena
0
P
PrintablesMarcus

Bosch GST 150 CE glideplate for 8 inch subwoofer

Made for Cut the main hole for 8 inch subwoofer with a Bosch GST 150 CE i use a 5mm bolt 40mm long

Pobrania
48
Polubienia
19
Ocena
0
P
Printablessnoty

2-inch hitch receiver plug

Don't want a fancy decoration but rather a plug? Here it is! This is for a 2" hitch receiver and a 5/8" pin. My F350 has a 3" hitch receiver that I keep a Curt 3.0>2.5>2.0 reducer sleeve in whenever not towing. I wanted to fill the 2"…

Pobrania
46
Polubienia
3
Ocena
0
P
PrintablesYolo

Neptune 4 Pro Rail-Webcam with 1/4 inch thread

ESUN - Tough PLA Grey 0.2 mm - height 4 walls 15 % gyroid infill Support on build plate for thread (isn't the most optimal but fits and holds) Rest of the settings in the png files Snaps into the rail, can't say how normal PLA will hold…

Pobrania
46
Polubienia
3
Ocena
0
P
PrintablesBigFinn

Wall, Tudor, V-shape, 2 inch

Tudor wall. Remix: https://www.thingiverse.com/thing:1598377/files

Pobrania
40
Polubienia
6
Ocena
5
P
PrintablesFabrizio

Softair Colt SAA 45 - Winchester Bulletts Canister

As for the title this is a SAA45 27 bullets capable container. Attention: use abundant WD40 on threads before the 1st coupling to ease it, then no more lubrication is required

Pobrania
40
Polubienia
6
Ocena
0
P
PrintablesAlvomane

Lenovo T16 + 16 inch Monitor foldable shelf/window sill or table mount | Lenovo T16 + 16 Zoll Monitor faltbarer Halter für Regal-/Fensterbank/Tisch

The holder is suitable for mounting a Lenovo T16 and a 16" monitor that can be folded back and forth on a shelf/window sill or table. The holder can be mounted on up to 21.5mm thick boards, tables or window sills (use the step file for…

Pobrania
40
Polubienia
16
Ocena
0
P
PrintablesKars

.96 inch screen case

.96-Inch Screen Case A 3d printed stand designed specifically for .96-inch displays. Whether you're working on projects requiring a sturdy stand for such screens, look no further – this is the ideal solution. Simply print the two parts,…

Pobrania
38
Polubienia
2
Ocena
0
P
PrintablesNina Máčová

Bird motif 3: Goldfinch coaster, grill, wallart

Bird motif 3: Goldfinch coaster, grill, wallart 10 cm, 20 cm (two colours / three colours)

Pobrania
37
Polubienia
13
Ocena
0
P
PrintablesDan Rogers

Disposable Tuna Can lid (fits 3 5/8 inch cans - 85.7mm)

Sometimes you have left over tuna or water chestnuts and don't use the whole can. Print one of these in PETG (dish washer safe) and it snaps easily onto the can. Extended flanges on two sides make it easy to remove. Rated disposable…

Pobrania
37
Polubienia
12
Ocena
0
P
PrintablesMitchelangelo

Fluid Distribution Cap - 1.5 (1-1/2) inch PVC

Fluid Distribution Cap for Hydroponic Agriculture applications or a Microgreen Machine. Distributes water to up to 8 ways. It is designed to work with 1.5" (1 ½") PVC pipe threads, and 0.25" (¼") standard rubber irrigation hoses.

Pobrania
36
Polubienia
14
Ocena
0
P
PrintablesClemens

Adapter 1.5 Inch Poolhose to G1"

Ich benuze den Adapter um auf der einen Seite ein Standard GARDENA Anschluss zu haben und auf der anderen ein 1,5 Zoll Poolschlauch anzuschließen. Die Version mit den Supportribs kann ohne weitere Supports gedruckt werden. In den Schliz…

Pobrania
35
Polubienia
2
Ocena
0
P
Printablescamdotcam

Kinchrome Soft-faced Hammer head 25mm

I drew this replacement head for kinchrome 25mm soft face hammer. I will print in TPU and Mylon later, but have so far only printed in PLA. The thread is M14X1.5 ISO and is around 10mm long Works well with no issues, (I've been using for…

Pobrania
34
Polubienia
1
Ocena
0
P
PrintablesSkyhigh

Sandpaper Storage 5inch - Additional Files

Found ClubbedEwoks Sandpaper Storage 5inch French Cleat with dividers and ROS positioner - parametric and love how it turned out but my collection of sandpaper included more grits than was offered. So used my slicer to put new values in…

Pobrania
32
Polubienia
2
Ocena
0
P
PrintablesBounet

6 inch Husky / Anvil bin inserts remix

Added an angle to the front bins for clearance and a big curve inside for easy access.

Pobrania
30
Polubienia
8
Ocena
0
P
Printablesmrog

Standoff for 5/8 inch (16 mm) tubing

My water softener has an overflow drain tube. I needed a way to position it above the floor drain, while maintaining an air gap. I designed these standoffs to hold the tube in place at an appropriate height. The screw holes are all just…

Pobrania
26
Polubienia
4
Ocena
5
P
PrintablesBego

Sharan spare wheel winch repair

Sharan spare wheel winch cable guide repair. When the wheel broke down, I discovered that my spare wheel located under the car could not be removed. After disassembly, it turned out that the steel rope that winds the wheel is twisted…

Pobrania
26
Polubienia
3
Ocena
0
P
PrintablesGo Boyz
Pobrania
25
Polubienia
1
Ocena
0