Wyniki wyszukiwania: shims

Sortowanie

173 modeli

P
PrintablesAinon3Dtisk

RC T98 Land Rover Defender shock absorber shims

Hello, Welcome to my profile, full of models and miniatures :-) I have for you RC T98 Land Rover Defender shock absorber support. Raises the car by at least 10mm!!!...the lift is really noticeable and the car is also more stable. It…

Wydruk około 0,37 €–0,46 € nettoWstępna wycena jednego wariantu

Pobrania
36
Polubienia
9
Ocena
0
P
PrintablesAndrew Leigh

Stepped horseshoe shims

I needed some shims to go behind some cupboards to keep them aligned when the wall is not quite straight. These fit over the wall screws. Three sizes which cover 1 mm to 10 mm.

Wydruk około 0,42 €–0,51 € nettoWstępna wycena jednego wariantu

Pobrania
35
Polubienia
5
Ocena
0
P
PrintablesREBELLION 10014

MAXSpline and SplineXL bearing shims

SplineXL tubes are notoriously loose in bearings due to the rounded crown of the tube. This provides little surface area to ride on the bearing. MAXSpline is slightly better, but can use some help on occasion. These tubes are 1 way…

Wydruk około 0,26 €–0,32 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
6
Polubienia
0
Ocena
0
P
PrintablesNeedItMakeIt

Bed Shims - Fits Creality K1 and K1 Max

I'd recommend printing the full set Print from ABS/ASA/PETG - I don't recommend PLA USE the thinnest LH possible for your printer After install, recalibrate your printer and redo input shaping.

Pobrania
23 332
Polubienia
1351
Ocena
4,95
P
PrintablesIAmAnEngineer

Ender 3 V3 SE/KE Bed Leveling Shims

If you encounter significant variations in bed level, especially in one of the corners, consider printing these shims and placing them under the bed supports. By doing so, your bed level will greatly improve and become easier to adjust.…

Pobrania
8968
Polubienia
1050
Ocena
4,98
P
PrintablesJan

Creality K1/K1 Max/K1C bed levelling risers/shims

UPDATE: Added 1.1 and 1.2mm shims UPDATE: New version with markings. It doesn't require to destroy the top level of bed to install, like some modifications i've seen before. It's designed, so you can put it from the side and rotate into…

Pobrania
5574
Polubienia
484
Ocena
5
P
PrintablesWMVos

Creality Ender 3 v3 SE/KE gantry shims for non-vertical gantry

I recently came across another Creality owner that had noticed his gantry was off axis, this will off course cause some serious layer shifting on bigger prints. Upon checking myself (I used the PEI sheet that comes along with the printer…

Pobrania
3161
Polubienia
570
Ocena
5
P
PrintablesMidori

Sloped bed shims for Creality K1, K1C and K1 Max

Recommended slicer settings: Layer height: 0.1 Initial Layer height: 0.1 Infill: 100% Print material: Preferably ABS+ or ASA, although I've printed it using PLA and it's holding up well. Tutorial: A good tutorial on how to use the shims…

Pobrania
2983
Polubienia
246
Ocena
5
P
PrintablesAlexey H

Creality Ender 3 V3 SE/KE Bed Leveling Shims for height compensations

The extended handle version can be used not only for the rear left bed level point but as a regular shim as it is more convenient to install

Pobrania
1937
Polubienia
229
Ocena
4,94
P

Anycubic Kobra S1 Bed level shims

I was struggling with my bed gantry being not level, and the Anycubic wiki wanted me to adjust the belt and leadscrews, but that was too much work for the fine adjustment I wanted to make, so I made these little spacers to go between the…

Pobrania
1467
Polubienia
145
Ocena
5
P
PrintablesFreshPrints

Anycubic Silicone Mod & Bed Spacer Mod , Parametric Shims and Spacers for Kobra 2 Max , Pro , Neo , Plus

Dial your bed In. Parametric Shims work with your Stock Hard Spacers and Silicone spacers found on AliExpress or Amazon Premade Shims for Stock Factory Spacer and Silicone Spacer if you don't want or need to adjust the size. No worries…

Pobrania
916
Polubienia
158
Ocena
5
P
PrintablesLH

X Belt Shims - Ender 3 V2 Neo

Straightens the belt path, increases accuracy, and reduces belt wear against X gantry. For Ender 3 V2 Neo , or similar carriages. This greatly increased the smoothness of the movement on my X axis. It's a must have mod in my opinion.…

Pobrania
845
Polubienia
177
Ocena
4,6
P
PrintablesWAABOOZ

ENDER 3 V3 KE BED LEVELING SHIMS

ENDER 3 V3 KE BED LEVELING SHIMS INCLUDED SPREADSHEET TO CALCULATE SHIMS OR SPACERS

Pobrania
749
Polubienia
34
Ocena
5
P
Printablesayman

Guitar Neck Shims (For Bolt On Necks)

100% infill at rectilinear is what you want. Pick something with detail ≤ 0.10mm to get a smooth shim. Thicker side is on top of text.

Pobrania
668
Polubienia
55
Ocena
5
P
PrintablesMaxymeanderings

Ender 3 Motor Shims

I made these shims to help line up the motor with leadscrew. The exact process is documented in my video on removing Z banding. These shims are not a one-size-fits-all, you will likely have to make them thicker or thinner based on your…

Pobrania
561
Polubienia
62
Ocena
5
P
PrintablesTodd Stansell

Blackstone Griddle Leveling Shims (1/8")

Leveling shims for your Blackstone. The original version provides a single size, which gives you a ¼" rise with a wheel. Each one you stack, though, gives you ½" increase. I needed ½" total height increase, so I wanted to remix this.…

Pobrania
444
Polubienia
42
Ocena
5
P
PrintablesTVJAB

K1 MAX BED LEVELING SHIMS

K1 Max bed leveling shims Category: 3D Printing

Pobrania
400
Polubienia
22
Ocena
0
P
PrintablesRoggason

Furniture Wedge Set – 1 mm to 5 mm Precision Leveling Shims for Furniture & Appliances

This 3D-printed Furniture Wedge Set includes five precise thicknesses (1 mm, 2 mm, 3 mm, 4 mm and 5 mm), designed for a wide range of household, workshop, and DIY uses. Each wedge provides an accurate, reusable solution for leveling…

Pobrania
399
Polubienia
36
Ocena
5
P
Printablesthe freewheeler

Prusa Mini | Anti-Vibration Feet Shims + Dampener Remix

Remix of Low Profile Prusa Mini Anti-Vibration Feet by Alexander Þór . This is the most effective upgrade I have made for my printer. Absolutely brilliant model. The printer wobbled after installing these dampening feet, so I modeled…

Pobrania
388
Polubienia
72
Ocena
4,29
P
PrintablesTrilobyte3D

Shimmy Shims (shim sizer, box and shims)

We've all got that one table that just doesn't sit right, or perhaps you're at the coffee shop and the chair keeps rocking. Here's your all-in-one quick solution to stop the shimmy: shims! Slide the sizer into the gap to quickly determine…

Pobrania
381
Polubienia
55
Ocena
5
P
PrintablesJmaxime89

Toilet shims

This is a simple shim for your toilet, it is ¼" at the highest point. I printed mine out of tpu so it is very durable I recommend printing at 0.2mm or higher so you get that staircase effect, that will help the shim stay in place. All…

Pobrania
341
Polubienia
23
Ocena
5
P
PrintablesEmkatech (Mike)

Shims Space Distance 0.5-12mm

This set includes distance shims in thicknesses from 0.5 mm to 12 mm , perfect for woodworking, furniture assembly, and any situation where precise spacing is required. Ideal for aligning, leveling, and adjusting components. Durable,…

Pobrania
280
Polubienia
68
Ocena
5
P
PrintablesSteveJohnsen

Door Hinge Shims - for aligning doors in their frames - for 3 1/2" & 4" door Hinges

Many door frames are not square, or the door hinges are not mounted correctly. This causes the door to not fit evenly in its frame. Often, a door will rub on the frame near the top on the latch side, making a rubbing squeal and/or making…

Pobrania
274
Polubienia
39
Ocena
5
P
PrintablesTVJAB

K1 MAX SLOPED BED LEVEL SHIMS

K1 Max sloped shims for leveling the print bed Category: 3D Printing

Pobrania
256
Polubienia
14
Ocena
0
P
PrintablesTom Horrocks

Stackable Shims

When I have a wonky table I like to level it with 3D printed leg extensions. However, I hate measuring how tall the extension has to be. No more! Now I can stack these 7 shims to make any block between 1 mm and 127 mm tall, in steps of 1…

Pobrania
232
Polubienia
28
Ocena
0
P
Printablestesseract

CORE One Bed Level Calibration Shims & Dust Cover 0.1 mm REMIX

The CORE One's bed can be tilted relative to the CoreXY kinematic's plane by a surprisingly high amount (up to about 1 mm height difference between edges). While this is compensated to some degree by the printer's automated bed level…

Pobrania
219
Polubienia
45
Ocena
5
P
PrintablesZerthron

Metric Spacer/Gauge Block Set/Woodworking Shims with Gridfinity combatible Box

I made this simple Gridfinity Box with Metric Spacer/Gauge Box in 1mm, 2mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm thickness. I colorcoded each Spacer and also labeled them with white numbers. Each Spacer also has the corresponding radius on…

Pobrania
201
Polubienia
43
Ocena
5
P
PrintablesNunya Bidness

Drawer face spacer shims

Here are some simple shims to help with installing drawer faces. They not only provide consistent spacing, they help hold the face in place while you are getting things lined up! Filename format: 12_2mm is for 12mm wood with a 2mm reveal.…

Pobrania
196
Polubienia
23
Ocena
5
P
PrintablesBoVisfeldt

Footholder w. builtin shims for leveling for Dewalt 7485/7492 and simila table saws.

I recently built a worktable with a space for my dewalt 7485 tablesaw in one end. As the table is on wheels, the saw sometimes get a little out of allignment when moving the table around. Also, the wood got slightly out of allignment…

Pobrania
191
Polubienia
46
Ocena
0
P
PrintablesFrankWL

Unterlegstuecke (Parallelstuecke) 1 bis 10 mm / Shims (parallel pieces) 1 to 10 mm

ReadMe.txt Unterlegstuecke (Parallelstuecke) 1 bis 10 mm Anwendung: Unterlegstücke mit 1 bis 10 mm Stärke. Dieses Sortiment ist eine Box incl. Deckel mit jeweils 3 Unterlegstücken je größe. Material: PLA Schichtdicke: 0,2mm Füllung: 25%…

Pobrania
176
Polubienia
27
Ocena
5
P
PrintablesGalinD

Shims for SABFOIL

Symmetric shims for Sabfoil fuselage, can be used to increase and decrease the angle of the attack on the tail. I have printed it with TPU, 0.1mm layer height.

Pobrania
171
Polubienia
8
Ocena
5
P
PrintablesKrhom

Walksnail Goggles X Comfort Shims

I find the default fit on the Walksnail goggles X very uncomfortable – they press on my nose. Theses shims will tilt the goggles up a notch, making them very comfortable to wear, with no light leak. I installed them by applying sticky…

Pobrania
169
Polubienia
16
Ocena
5
P
PrintablesHigany

M42 T2 spacers, shims for adjusting correct backfocus

With numbers which makes them easier to identify, especially at night. I printed my set from PETG, 4 perimeters, 100% infill. Might need a bit post processing to touch up any PETG stringing and smoothen the numbers.

Pobrania
151
Polubienia
5
Ocena
0
P
PrintablesBenevolensky

Vortex Viper PST Zero Stop Shims

Vortex has discontinued their Zero Stop shims for the gen 1 PST series scopes. I needed a bit more space than what my original shims could do, so designed a set of additional shims I can use. Made a set of 5 thicknesses, from 0.2 to 1.0.…

Pobrania
144
Polubienia
10
Ocena
0
P
PrintablesToDumToNo

Eufy Video Doorbell Angled Shims

Eufy Video Doorbell 2k angled shim to be used in conjunction with the provided left/right angled bracket. The shims included are specific if the Eufy angled bracket angles to the right (angled to the left when looking directly at the…

Pobrania
142
Polubienia
7
Ocena
0
P
PrintablesgatoAlfa

Shims for the 2024 Ioniq 5 trunk guides

Some Ionic-5s have an annoying rattle coming from the trunk lift gate making side-to-side movements while driving. Some dealers will help with this, but I decided to try with some simple shims after hearing how it is handled by the dealer…

Pobrania
137
Polubienia
8
Ocena
0
P
Printablesragrum

Breville Bambino Plus Drip Tray Shims (1.5 mm)

The metal grate on the Breville Bambino Plus drip tray does not sit tightly on its plastic reservoir, so it rattles around while the coffee machine is running. I've designed some small shims to attach to the plastic reservoir that keep…

Pobrania
136
Polubienia
23
Ocena
5
P

Door Hinge Shims with Slip-In Installation

Shims are commonly added behind door hinges to adjust the gap between the door and the jamb. These door hinge shims are designed to slip behind the hinges without needing to fully unscrew the hinge from the jamb. Included are shims in 1mm…

Pobrania
133
Polubienia
19
Ocena
5
P
PrintablesMC1457

RC Steering Servo Shims

These shims fit the ANNIMOS 20KG RC Servo (Amazon https://www.amazon.com/gp/product/B0769DFJVK). I found that the stock fit on the 3DSets Buggy ( https://www.3dsets.com/product/model-7-buggy/ ) cause the steering to bind. These shims…

Pobrania
129
Polubienia
16
Ocena
5
P
PrintablesPrintMills

Cabinet face spacer blocks or shims

Use Case Similar to my other model on drawer slides, when it came time to attaching my drawer faces to my built in garage cabinets I needed a repeatable spacer. For years we used a deck of playing cards with success. I originally build…

Pobrania
121
Polubienia
24
Ocena
0
P
PrintablesMichael G

Drying box-roller、Shims

The materials you need to purchase are as follows: 1、8mm diameter linear shaft with a length of 493mm x2 2、608ZZ bearings x24 The materials you need to prints 1、roller x12 2、Fixation of both ends of the spool x4 3、Shims between bearings x14

Pobrania
120
Polubienia
31
Ocena
5
P
PrintablesAndrew Nelson

14MM Airsoft Muzzle Device Timing System (Shims)

14MM Airsoft Muzzle Device Timing System (Shims) These shims are printed and used to tighten muzzle devices (flash break, suppressor, tracer unit, etc) on 14MM Airsoft barrels to specific orientations. The shim(s) should fit between the…

Pobrania
118
Polubienia
13
Ocena
0
P
PrintablesMat

Shims - general purpose carpentry / construction shims

Here's a few reasons why you may NOT want to 3D print your own shims, can you think of any more? Dimensional accuracy of shop-bought shims is better (do I care?) Shop-bought shims are about 2% cheaper. Last year they were about 30%…

Pobrania
117
Polubienia
21
Ocena
5
P
Printablesharaldan

Angle Shims for the Multifunction Arm mounting system

The Multifunction Arm system is fantastic, but, being made from plastic, not 100% rigid. Gravity, on the other hand, is a bitch, and won't hesitate to flex and bend the system until your screen or other device on the end of the arm is not…

Pobrania
116
Polubienia
47
Ocena
0
P
Printablespdien

Gamesir G8+ Shims for OnePlus Open

This makes using the OnePlus Open with the G8+ more comfortable by keeping it centered and leveled as the phone has an absurdly large camera bump making it lopsided, giving it a chance to pop out of the controller.

Pobrania
113
Polubienia
10
Ocena
0
P
Printablespatta

Microscope RMS shims / washers

This is a set of shims for RMS /DIN microscope objectives. Yes they are simply rings, thechnically they are washer or shims. Here uploaded a set of them with thickness 0,1 - 0,2 - 0,3 - 0,4 - 0,6 -0,8 -1,0 - 1,2 - 1,4 _ mm Inner diameter…

Pobrania
110
Polubienia
7
Ocena
0
P
Printablesqueueeeee

Ender 3 V3 KE Gantry Shims labeled

Ensure first layer is good enough. Obviously these shims are for helping fix that, but these need as good of a first layer as possible. 0.3mm first layer can help mitigate any issues. Just print slower than you normally would. I use Orca…

Pobrania
107
Polubienia
13
Ocena
0
P
PrintablesNenjaBen

Shims - with groove for screw

I inherited a rolling table for the garage from my dad, but the top was not flat. Designed these to cradle the screws under the top so I could true up the top. Fits nicely on top of standard 2x lumber (1.5"). Just change the Z height to…

Pobrania
99
Polubienia
9
Ocena
5
P
Printablesmiiiikeb

Recurve Archery Bow ILF Limb Shims

ILF Recurve Shims Precision-fit shims for quickly adjusting limb pitch on ILF recurve bows—just like adding limb bolt turns, but without touching the bolts. These are great for training with a slightly heavier draw or quick re-tuning for…

Pobrania
94
Polubienia
16
Ocena
0
P
PrintablesMiguel Herrmann

Dji Fpv Goggle Shims for Narrow faces

This is a modified version of the "Dji Fpv Goggle Shims" made by kwboost. My head is quite narrow, so I made this version thicker, and shifted more towards the top of the face plate. Have a look at the instructions provided by kwboost:…

Pobrania
94
Polubienia
9
Ocena
0
P
PrintablesHardwire Design

Dogear P90 Shims

Sometimes, on cheaper guitars especially, the pickups are way too low and that impacts the sound quality of the guitar. These shims raise the height of P90s. They go between the pickups and the body of the guitar. 2.5mm Tall, you can…

Pobrania
93
Polubienia
5
Ocena
0
P
Printablesaiber

Front derailleur shims, 28.6 to 34.9 mm

Shim for 28.6 mm diameter seat tubes to accept 34.9 mm (mountain) front derailleurs. The 28.6 mm diameter may come out a little small, but the print flexes enough to grip the frame just fine. 14 mm tall. I think I made this a long time…

Pobrania
92
Polubienia
3
Ocena
0
P
PrintablesDror Avrahami

Cabinetry Shims and a Box

Simple box for shims for cabinetry, containing shims in the following sizes: - 10mm - 4mm - 3mm - 2mm For the joints you will need 2 M2 8mm hex screws For the latch you need 2 M2 16mm hex screws. If you only want the box, with no shims…

Pobrania
87
Polubienia
10
Ocena
0
P
PrintablesDynaMight1124

Team Associated B6.x, B7, B74.x rear pin shims

I recently lost a shim in the grass at the track when changing the toe, turns out you'd have to buy brand new rear arms to get more plastic shims!! so I designed these. The kit ones are 2mm, so if you want replacements, then print a load…

Pobrania
84
Polubienia
12
Ocena
0
P
PrintablesJimbo70

20x40 V-Slot shims

I have built the Prusa i3 Bear Half ( https://www.thingiverse.com/thing:2562174 ) which is a Prusa i3 frame upgrade. Cutting the 20x40 to the correct length is critical to obtaining a square frame, but in actual practice such cuts are…

Pobrania
83
Polubienia
9
Ocena
0
P
PrintablesMiricius

LaTrax Teton/Rally/Prerunner differential shims

LaTrax Teton/Rally/Prerunner differential shims, because I cannot find the shims local , so I 3d printed them , I recommend to put the shims like this, shim first, after , bearing

Pobrania
80
Polubienia
8
Ocena
5
P
Printablesngbfish

Various Bike Seatpost Shims

When trying to find shims to go between seat post for my mountain bike and Tout-Terrain Trailer collar I couldn't find quite the right size… so I made my own. I have uploaded my own sizes that I needed and also a link to a file where you…

Pobrania
80
Polubienia
6
Ocena
0
P
PrintablesSionide21

IKEA Billy Leveling Shims

Pairs of shims are available in 1mm increments up to 10mm. If not printing the pair, be sure to select the correct side. They are not interchangeable.

Pobrania
78
Polubienia
14
Ocena
0
P
PrintablesDreded

Strengthened Bolts & Shims for Flexible & Sturdy Phone Arm

My Bolts are MUCH stronger and use 30g less filament than the originals (mainly due to me using 12mm heads instead of 25mm ones) The XL phone holder fits my S24 Ultra with a case perfectly. I printed the phone holder in PETG and the…

Pobrania
78
Polubienia
12
Ocena
0
P
Printablesbruchsturm

Water-saving shims for shower head

Energy prices are skyrocketing, winter is coming, and unfortunately I'm heating my water with electricity, so I've designed this shim to reduce my energy bill. I'm using the 3.5 mm version and was able to reduce my water flow from 12…

Pobrania
78
Polubienia
8
Ocena
0
P
PrintablesFlibblebot

K40 Mirror Shims

I've finally got round to aligning the mirrors in my K40 laser cutter. Using the mirror alignment guide on k40laser.se, I needed to raise mirror 2 a little to get the alignment perfect. I tried using washers, but that was just too awkward…

Pobrania
75
Polubienia
5
Ocena
5
P
PrintablesBee

Leveling bed shims for creality ender - 3 v3 se/ke

Just leveling shims with 2mm and 3mm…free to use.

Pobrania
74
Polubienia
9
Ocena
0
P
PrintablesNicklascs

Stackable Spacers / Shims for Leveling and Mounting

These spacers are 60mm x 25mm and designed for easy and precise height and distance adjustment between two surfaces. They can be used for tasks like leveling a tabletop, raising cabinets, or creating a consistent gap between components.…

Pobrania
74
Polubienia
7
Ocena
5
P
Printablesaiber

Front derailleur shims, 31.8 to 34.9 mm

Shim for 31.8 mm diameter seat tubes to accept 34.9 mm (mountain) front derailleurs. The 31.8 mm diameter may come out a little small, but the print flexes enough to grip the frame just fine. 14 mm tall. Made in Autodesk Inventor.…

Pobrania
74
Polubienia
5
Ocena
5
P
PrintablesRyan Perry

Small Shims 1/16, 3/32, 1/8

Some basic shims to use in all sorts of different applications, from shimming something level to shimming out the side of a stud or wallboard to make something perfectly level. I made them to replace some various sizes in a board shim…

Pobrania
71
Polubienia
3
Ocena
0
P
PrintablesB&B TECH

Screen door latch shims

shims for screen door latch, hole spacing 44mm.

Pobrania
70
Polubienia
5
Ocena
0
P
PrintablesSEDAudio

Bowers & Wilkins PX Arm Shims

I loved my Px, but they have silly flimsy arm designs (thanks to Native industrial designs for being very practical), and mine broke after a few years of abuse. Supergluing the arm back into the slot was ineffectual because there is…

Pobrania
65
Polubienia
4
Ocena
0
P
PrintablesRobotAnna

Furniture Shims

If your furniture is not sitting level, put these shims under its feet. If you need a different size, try altering the size in your slicer. The bgcode is sliced for PLA filament, Prusa MK4S. This design is available on Printables ,…

Pobrania
64
Polubienia
3
Ocena
5
P
PrintablesIan A Scott

Sovol SV08 Print Bed Shims

I was having difficulty printing the gridfinity grids due to my bed being wavy with a 3mm difference across the bed. Added the shims and now I get perfect gridfinity grids. Various heights to choose from raniging from 0.2mm to 3mm. Use…

Pobrania
63
Polubienia
11
Ocena
0
P
PrintablesIso

SV08 Enclosure shims

I really hate how Sovol provided no provision for properly sealing off or even attaching the bottom edge of an enclosure in the shape of the base. So… I made these up, to give a surface for attaching some foam tape, and to provide some…

Pobrania
62
Polubienia
16
Ocena
0
P
PrintablesAsus1357

Magswitch 95 shims

This is for the Magswitgh 95 Since the Magswitch mounting height is 3/4" and I use Baltic Birch (which is only 18mm) for my jigs which makes the switch sits proud of the base by 1.05 mm which is not a good thing. So I made a couple of…

Pobrania
61
Polubienia
14
Ocena
0
P
Printablesspiggytech

spiggytech Ankermake M5 T-Volcano Hot End Mod Shims

These are 4mm shims meant to clip inside the Z-Axis towers to make the M5 compatible with Volcano hot ends. Print 2x, PLA/PETG @30% Cubic (100% recommended) You will need the following items: Polisi3D Volcano Hot End Block Volcano Nozzle…

Pobrania
61
Polubienia
25
Ocena
0
P
Printablesgexgecko

Bolt guides, washers, wing nuts, AND pressure shims for Ortur 'Better Cutting Effect' laser engraving cutting honeycomb mat

I had to bump up the size of the M8 wingnut designed by ‘ Meister Edel ’ so it would work with my p8 nozzle. The tapered washer is just to make turning the wingnut easier when it is sitting on top of one of the metal guides. The slider…

Pobrania
60
Polubienia
16
Ocena
0
P
PrintablesSteve

Printable Capped Bed Shims

A simple printable method using stock parts to simplifier placing shim stacks unders the stock 8dia steel supports. Consists of a cap that can contain the needed shims over the stock metal support allowing easy placement between the…

Pobrania
58
Polubienia
5
Ocena
0
P
Printableszoster.ar

North Sonar hydrofoil shims

The ones with the square are 1 degree, the ones with triangle are 0.5 degree. Stack them to obtain more than 1 degree. I printed in 0.7 layers with turned down speed (takes less than 10min per shim). I attached the Prusa Slicer file in…

Pobrania
57
Polubienia
4
Ocena
0
P
PrintablesViktor

BMW e36 differential spacers/shims

Set of differential shims type 188 for BMW E36 is used to limit the clearance between the differential gears. Thickness 1-2mm. Individual parts need to be printed with different settings to maintain the thickness (height) of the shims…

Pobrania
55
Polubienia
18
Ocena
0
P
PrintablesLloyd Keays

Various Shims (Flush in this Instead of useless poop in Bambulabs)

Save filament instead of Poop! I surprisingly use a lot of little shims in all sorts of situations to add stability to an uneven part or to space things or whatever. When printing in multicolor in Bamboulabs you can select a file and…

Pobrania
48
Polubienia
14
Ocena
0
P
PrintablesKyle Bopp

M3000 Custom Shims

The shims that came with the shotgun didn't work for me, so I made my own!

Pobrania
47
Polubienia
3
Ocena
0
P
PrintablesSynthead

Ender 3 NG v1.2 electronics top shims

Got a gap between the “electronics top A” and "electronics top “B” parts on your Ender 3 NG v1.2? Hide your shame with one of these shims! This is a really common defect on Ender 3 NG v1.2 builds. Here is a gap present between the top…

Pobrania
46
Polubienia
18
Ocena
0
P
PrintablesDmur

Shims for BMW shifters

Fits E46 & E60 shifters (tested on 25117546373), but should fit on most BMW shifters. BMW shiftsticks have inherent play due to the rubber connecting both halfs, even brand new ones. This will help remove that play down to near 0, or make…

Pobrania
45
Polubienia
7
Ocena
0
P
Printableswikallen

Prusa Core One+ Spool Holder Oring Shims

These are shims to help set the tension of the Oring for the Spool Holder on the Prusa Core One printers. Needed if your orings are too thin to give the spool holder the right amount of tension when locking into place. .5mm, 1mm, 1.5mm…

Pobrania
45
Polubienia
4
Ocena
0
P
PrintablesMartin Fossen

Raymarine transducer nut and shims

Inside threads would benefit from printing with thinner layers (used 0.12 myself, but could go a bit higher). Also added a thread test piece if you want to test the threads.

Pobrania
44
Polubienia
5
Ocena
0
P
PrintablesDiego Moreira

Creality Ender 3 V3 SE/KE Bed Leveling Shims

Creality Ender 3 V3 SE/KE Bed Leveling Shims. A slot has been added to facilitate shim installation, eliminating the need to remove the table. You simply need to loosen the screw and lift the table slightly to insert the shim.

Pobrania
43
Polubienia
5
Ocena
0
P
PrintablesCALMONE

Mini shims / wedges

I needed to make a door stop a little more tight and so I made these mini shims to do the job.

Pobrania
41
Polubienia
3
Ocena
5
P
Printablesmatmx

Ikea Mittled Shims

I installed 2x Ikea Mittled 40cm light bars into my Original Prusa Enclosure by attaching them to the existing holes in the ceiling. Since the LED bars are only loosly fitting on their mounts and can move left and right I noticed that…

Pobrania
41
Polubienia
3
Ocena
0
P
PrintablesHroller McKnutt

TPU mast shims

Just slapped together some quick shims for my rotator so the masts can't twist.

Pobrania
39
Polubienia
3
Ocena
5
P
Printablesenrico leite

Shims Fanatic Foil

Shims Fanatic 100%

Pobrania
37
Polubienia
2
Ocena
0

Ikea IVAR Cabinet with Sliding Doors Shims [Fixes Height Mismatch]

Ikea IVAR is great system that's very customizable. I just didn't like that in my system the top of my sliding door cabinet didn't line up with the shelves surrounding it. So, I made these shims and posts to insert on the underside of the…

Pobrania
36
Polubienia
30
Ocena
0
P
PrintablesTocache

Shims (spacers) for Black Noctua Fan holes (Prusa I3 MK3S)

I've created this shim (spacer) to fit a cover for the Noctua fan of my Prusa I3 MK3 printer, with this thing the cover sits flat on the fan. For the fan cover, I used this thing: https://www.thingiverse.com/thing:2917644 Print…

Pobrania
36
Polubienia
3
Ocena
0
P
PrintablesRealnuf

flat shims

Series of different thickness of shims that I used used to level 1"x dimensional lumber with 1"x furring strip lumber during model train benchwork assembly, but can be used wherever a flat shim is needed. Category: Other

Pobrania
36
Polubienia
1
Ocena
0
P
Printablesmatthijsbos

Shims for MR-13B Drill Bit Sharpener

1.0mm and 0.5mm shims for Vevor MR-13B drill bit sharpener, allowing for more aggressive cuts. recommended 0.1mm layer height for strength. Onshape document:…

Pobrania
36
Polubienia
4
Ocena
0
P
Printablessacreblube

IKEA MARKUS Hydraulic repair. Adjustable with shims

Printable piece to lock IKEA's MARKUS chair at a height of 90mm with 5mm shims to adjust to the chairs maximum height of 115mm. Shim shown in grey in photo. Useful if the chairs hydraulics are beginning to fail and the chair drops by…

Pobrania
34
Polubienia
5
Ocena
5
P
Printablessnail

50mm FMS EDF to XFly shims

I was using a 50mm FMS EDF in the Skyray model published by PTIKyle. The FMS EDF has a narrower bell and a narrower body than the XFly units, resulting it in falling into the duct and not being sealed. This is a quick shim set to make the…

Pobrania
32
Polubienia
2
Ocena
0
P
PrintablesOliver Abbott

Screen door latch shims

1mm-16mm shim for screen door latch

Pobrania
30
Polubienia
4
Ocena
5
P
Printablesnaxxfish

London Metropolitan Line A-Stock luggage rack mounting shims

These shims allow the user to mount a real London Underground Metropolitan Line A-stock luggage rack to their wall. The London Transport Museum sells recommissioned luggage racks - which are replicas from the 1960's Metropolitan Line…

Pobrania
30
Polubienia
6
Ocena
0
P
PrintablesDanAndersen

Sunlu S8 Shims to use Ender 3/CR10 Z-Axis Leadscrew Top Mounts

To make a nice top mount for the Sunlu S8 Z-Axis Leadscrews, you can use the typical Creality Ender3/CR10 Solid mounts, when you add a little spacer. Print this one twice and you are good to go. Mine are:…

Pobrania
30
Polubienia
1
Ocena
0
P
PrintablesAgu

MGN12C Shims

These prints are to made with 100% infill, but depending on the top layer counts you have that may not matter. Helped a lot to level the bed.

Pobrania
29
Polubienia
3
Ocena
0
P
PrintablesOnyhr

Armstrong Performance Mast Shims

These shims are to move the board nose down on the Armstrong Performance Mast specifically to tune in for pump foiling and dockstart. The Armstrong Performance Mast has a built in rake angle of 1 degree which noses the board up so the 1…

Pobrania
28
Polubienia
1
Ocena
0
P
PrintablesDan Rogers

Slope shims for Vivosun Hydroponic system

Shims to create a positive drainage flow across each tier of a Vivosun hydroponics system. 5 shim heights - 0 inch, 1/8 inch, ¼ inch, 3/8 inch and ½ inch 8 Shims per tier level, you will need 3 sets of shims for the 3 tier rack. Each shim…

Pobrania
28
Polubienia
6
Ocena
5
P
PrintablesSpikeon Studio

Gridfinity Legs - Shims

A set of shims to allow you to create perfectly vertically aligned Gridfinity systems with Gridfinity Legs

Pobrania
28
Polubienia
11
Ocena
0