540 modeli
Simple and easy to print filament waste bin for QIDI Q2. Unlike most other models does not require any additional hardware (magnets, screws, adapters, etc.) to mount. The hook/latch design relibly holds the bin in place while still being…
This waste box brings rolls the purge material to the front (as original model) but also added a drawer to make simple the emptying of the box without moving the whole box. It can be important, if you do not have much space and you want…
This is a clip-on poop chute/bucket for the QIDI Q2 , designed to collect purge material neatly without any screws or permanent modifications. UPDATED Small Version (RECOMMENDED PRINT) : Added Chamfers to improve Printability Added Holes…
Riser with vent for the QiDi Q2, this is found on the QiDi Wiki page, but I am uploading it here so it is easier to find. Prints easy, I used .2 LH and the “.2 strong” setting. I use automatic, normal supports with the stock settings set…
Spacer for stable TPU printing for the QiDi Q2. In the stock setup, there is a 2.6–2.7 mm gap between the front wall of the feeder housing and the drive gears, where soft TPU filament can sometimes slip out. With this spacer installed,…
Qidi Q2 — Performance Cooling Duct (v5.1 & v6.0 Dual-Flow) Summary A high-efficiency part cooling shroud for the Qidi Q2 . This duct was precision-engineered using CFD (Computational Fluid Dynamics) to reduce turbulence and provide a…
Print with 3-4 perimeters for strength and use the orientation it imports in as no supports are needed. I’d recommend PETG, PCTG, or ABS since they are more flexible than PLA or ASA and more forgiving of tight tolerances. You may need to…
This is a simple but functional dual purpose clip designed for the PTFE tube/push fitting on the Qidi Q2 toolhead. The clip acts both as a locking clip to prevent the PTFE tube from being removed and it also straightens the PTFE tube to…
UPDATE 11/09/2026 Someone had issues with the front cover while using the polar cooler so you should be aware that these covers were made before the polar cooler and from what I can see they won't fit without some hacking. I Will consider…
Stock cooling duct on the Q2 is very imbalanced and the left side suffers from poor cooling as a result. I designed this duct and fan mount to correct that and simultaneously improve the cooling performance. It is drastically better. It…
A purge waste bin. It doesn't vibrate loose, it doesn't require tools or printer mods, and it doesn't block vent slots. It's wider than it looks in the pictures, and, like a certain police box, it's bigger on the inside! What makes this…
An issue with the Qidi Q2 is that the internal PTFE filament tube rubs against the underside of the glass lid. Even worse, it scrapes across the screw heads which hold the lid's handle in place. A common solution is to print a riser for…
The underside of the platform feet isn’t perfectly flat, so the bed never references a true plane and dual-Z drift makes it worse. These blocks give a flat, rigid reference, so the platform squares quickly and stays consistent. They can…
Modified version of Allan's QIDI Plus4 foot to fit the Q2. This raises the Q2 1cm off your desk, and provides a wider base for stability. For my printer this increased stability and reduced vibrations. These may require more work, your…
I've got my Qidi Q2 and tools were just in a plastic bag, I've decided to store it in a box.
This is a dust cover for the enclosure. It prevents dust and important bolts from getting in. I made this because I lost a bolt for my M3. It works better if you use double sided tape.
This riser is designed to accommodate the QIDI Q2 glass lid. I’ve included the STEP file via Onshape to allow for easy customization, particularly if your foam tape dimensions differ from mine. Materials Used: ½" × ½" foam tape M2 heated…
QIDI Q2 Riser I redesigned the original H3D-Himon riser because the top glass wasn’t lifted high enough — the PTFE tube was still scraping against the glass. This version increases the height by about 45 mm , giving the tube enough…
My first attempt, which was oval race-track shaped with a very shallow 20 degree leading edge still managed to catch the PTFE tube. So, I modified the design to be more inspired by cow-catchers on the front of trains. I printed it in PETG…
Open the corresponding 3mf file with "Open project...", select your filament and nozzle, use 0.2mm layer height, slice it and switch to the temperature tab. Check that there are multiple temperatures. --> Print and have a look at the…
Filament Purge Bin for QIDI Q2 . Keep purges under control—whether you print multicolor or single-color with frequent filament changes. Designed exclusively for the QIDI Q2, it mounts cleanly and keeps the chamber tidy without permanent…
Are two pieces not enough? Print as many as you need. To insert the clip, you need to disassemble the desired segment of
This is a replacement glass door handle for the Qidi Q2. It is much larger (while still looking nice), making it significantly easier to open/close the door comfortable. Uses the screws & bushings from the original handle.
This model is a large capacity desiccant vessel for the Qidi Box. It's best filled with a funnel or chute with one of the side plugs installed and before installing it in the printer. It keeps the box much dryer than the original packets.…
UPDATES 11/14/2025 Version 1.11 Made a version of the cooling duct for the more common small mouth 5015 fan. Added a honeycomb version of the cooling duct bottom panel. Also removed the curved wall on the inside of the fan area for the…
I designed this spool holder for QIDI printers because the original one, when used with cardboard spools, often created too much friction. This could lead to false filament tangle detections and also generate annoying noise. After…
Build plate holders for 280mm x 280mm build plates. Primarily made for the QiDi Q2 but can fit any other build plates of similar size. Recommended print settings: PETG 3 walls 10-15% infill 5 bottom, 5 top layers You can print this on the…
The printable wrench for the bed leveling nuts is quite loose, and the nuts themselves are pretty tight. I made a newer version that tapers slightly, gripping the nuts much better. I printed this in PLA and it holds up well, unlike the…
NOTE. YOU WILL NEED TO ROUTE THE PROVIDED QIDI BOX PTFE TUBING THROUGH THE HOLE NEXT TO THE RUBBER WHERE IT WAS PREVIOUSLY ROUTED PRIOR TO INSTALLATION, I HAVE BEEN USING IT THIS WAY FOR A MONTH OR SO NOW WITH NO ISSUES. A simple…
I chose this model was because of the “Height”. I have noticed the power wires at the right-back corner, which means we would need more space to make sure the wires won't interfere with the platform leveling process. And the stage I have…
Clip on Camera Hood for the Q2 to reduce flare and blooming from LED lights. One is for front (stock) and 200mm LED light bar (see my other models) and another that blocks entire top (for people with risers with light strips). Suggest…
Top mounted filament spool holder for printing soft TPU on QIDI Q2. Can be used without removing QIDI Box. Uses spool axle design from Cell Spool Winder . Parts needed 1x Axle.stl 2x Side.stl (Optional) Axis drive 01.stl and Axis drive…
er PTFE am Hotend neigt sehr zum Abknicken. Dadurch gibt es Probleme beim Wechsel des Filaments bzw manuellem Nachladen des Filaments.. Das verwendete Filament zum Drucken muss zum im Drucker verwendeten Filament passen.. Wenn die…
UPDATE 29/01/2026 Added STEP files and updated the "Wide mouth with fin" model with 2 fillets. UPDATE 06/11/2025 Added models to fit 5015 fans with wide mouth, like the stock one. One model is basically as the stock housing but with…
I like this model more than all the others I found because it rolls the purge material to the front and doesn’t require you to move the bin to clear it out
For tpu print. defend z holes from trash. carefure with termochamber. Model : Volvik88 @choolkov
The Handle provides a firm grip and the Screw cover allows for easy movement of the PTFE tubing. Bolts M3x10mm 2pcs Nuts M3 2pcs Use a creep resistant material such as PETG. The layer pitch must be 0.2 mm and the total number of walls…
4-Inch Exhaust Duct for Qidi Q2 – Improved, Optimized, and Easy to Install Upgrade your Qidi Q2 airflow setup with this redesigned 4-inch exhaust duct , engineered to offer smoother airflow and easier hose connections compared to the…
I recently bought a QIDI Q2 . Initially, I was considering the Bambu P2S , but the Bambu was simply too expensive for my allowance. When it arrived, I was surprised to find that the airflow from the model fan was weak . At first, I…
⚠(DISCLAIMER)⚠ MY MODELS ARE PUBLISHED UNDER THE CC BY-NC-SA 4.0 LICENSE: https://creativecommons.org/licenses/by-nc-sa/4.0/ You are welcome to download, print, share, and remix all my designs with credit, but you may not sell any of my…
A large pull handle to replace the factory one (or another printed one). Uses the factory screws to attach the stock handle. Printed in PETG since its all I had in silver but i'm sure most filaments outside of PLA will be fine (and even…
Q2 2 is quite low on the table. Also has the PSU on the bottom sucking all the dust and particles there. I looked and it was quite warm underneath due to PSU and Z stepper motors working in a very narrow space. I raised it by about 1 cm.…
Qidi Q2 60mm tall riser with vent sliders and internal/external accessory mount points. None of the existing published designs had all the characteristics I wanted, so I created my own. I modeled this in TinkerCAD, and the STEP files were…
Simple cover to prevent debris from falling into the holes around the Z-rods. It should be printed in a heat resistant material. I printed them in ASA. 2025-12-27 v1.5 Thanks to Gleb Grigorian for making me aware of the forgotten screws…
Qidi Q2 Waste bin, can be clipped on. Poop Bin
UPDATES 12/26/25 Added a version of the back panel that doesn't have the PTFE tube cutout in the top right corner. Added a printable TPU plug for the top right corner TPFE guide cutout. Removed the unused holes to mount the Qidi box hub…
This is a simple poop box I created in Fusion emulating the body style of the Printer with an embossed QIDI logo. Print it in black or silver for matching body color palette. I did not want anything wrapping around the unit so this is…
This allows you to fasten a 3" flexible duct to the QiDi Q2 exhaust port. The original model that I remixed this from (thanks Weav ) was very good but I had already designed other duct work that had a lip at the end of the tube to “catch”…
If you've ordered new nozzles, you've been impressed with the boxes that Qidi ships them in :) This insert sits in these boxes and gives room for nine nozzles. Why print a whole box when theirs is so good?! The insert has been designed to…
New Handle for multi colour 20 Feb 2026 Added another Handle ( Fits Both Door and Lid) using original screws. 13 Jan 2026 Printed in Qidi ABS Rapido Silver, using Qidi Studio with Qidi ABS Rapido Metal filament profile. Printed in upright…
Use to attach a 3 inch vent hose to the exhaust port on the Qidi Q2. You will need to stretch over the coupler as this is a bit larger than 3 inches but provides a snug fit to the hose. Printed in PETG. I used m3x8 self-tapping screws.
An attempt to make a simple to print and easy to use filament waste bin. There are two versions of hangers: V1 - Mounting in standard sockets using extended screws (requires 2.9 x 16 mm with countersunk head). V2 - Since I didn't have the…
A tool to easily disconnect the PTFE tube from the qidibox buffer. You no longer need to lift the buffer to expose the coupler. Just insert this into the hole where the tube is and push down to release the coupler and then pull the tube…
This is a low tolerance, tight fitting model. It is low profile (only 1mm proud), and interlocking. The shoulder/lip is minimally wide, and has a spot to catch an edge if for some reason you ever need to remove them. I printed in PETG. Be…
This part prevents the TPFE tube from touching the lid.
Function ：Guide waste material to slide down from the left side of the printer via the chute. Key Features 1. No original part replacement, easy installation 2. Metal-free, fully 3D-printed 3. Printable with any material 4. Only 51g, easy…
A very simple cap for Qidi q2 riser sent with Qidibox: Prints ok with PLA, maybe best with PETG ...
HULA Center Core - Modern and Perfect fit for QIDI Q2 & Q1, no need remove original feet!
TPU feet for: https://www.printables.com/model/1411842-qidi-q2-foot-support-with-extra-clearance Didn't feel like printing the whole thing from TPU, so I made these. The bottom is 2mm thick. 3 walls, 3 top/bottom layers, 20% gyroid in TPU…
After creating a similar exhaust adapter for my Core One, I decided to design one for our office's Qidi Q2. This adapter takes the Qidi Q2 exhaust to a 120mm PC case fan, with another adapter to 4" exhaust hose that will be run to a roof…
Prevents PTFE tube from snagging. Snaps right into place
The bin is kept in place with 3 hooks which enter some ventilation holes. In that area is the ventilation for the SSR unit responsible for heating the chamber. I felt like to block 3 out of 5 vents slots was not ok. I made some holes to…
An alternative version of the PTFE tube holder for the QIDI Q2 3D printer. The holder is slightly smaller in size and has a slightly larger tube opening. Three options are available: a straight one and two with a slight upward lift above…
First off, I wanted to upload this as a paid print, only because it took me a lot of time and filament in prototyping, but minimum price was 5$, so here we are - it's free. This riser is meant for Qidi Q2 with the original riser. The…
This modification is at your own risk. Upgrade the Q2's part cooling fan to a Bambu X1 or P1 fan. Transplant the Q2 cable to the bambu fan. At this time, cross the two cables on the left. The fan power will be overwhelmingly strong, so…
Changes made for G-code to work on Qidi Studio. although temperature changes between layers is not perfect it'll get the job done for testing new filaments.
A simple rail cleaner for the x-axis of the Qidi Q2 (should also work with Q2C, let me know), dimensions are sightly tuned to allow to put some microfiber cloth or whatever you use between the tool and the rail. Can be used both on top of…
This KeyChron replacement Knob is a perfect fit if printed on a well tuned machine. If your printer is a little sloppy you might need to scale it up slightly. I print these top down but you can certainly flip it and print with supports if…
UPDATED 20/01/2026 Screw holes adjusted according to user feedback. Fits both front and top glass panels. SLICING: For the cleanest look use scarf seam painted over the surface where the screws go. .12 layer height, 3+ walls, infill at…
Designed for using M3x12mm socket head cap screws, but this requires enlarging mounting holes on the back panel.
When using the QIDI BOX with the QIDI Q2, a riser is included and the filament inlet on the riser is used instead. The original filament inlet on the Q2 becomes unused. This plug is designed to cover that opening to reduce heat loss from…
Also, there is no need to position the model at an angle during printing. With the bridges set up and the organic supports manually adjusted (screenshots), you can print as is.
Remix Bin with no supports required for the handle, thinner walls and optional lid for this model
If your filament is not retracting properly (the spool doesn’t rotate) and instead unwinds inside the Qidi Box instead of going back onto the spool — this model fixes that problem. This spacer reduces excessive pressure between the…
A purge chute I made for the QIDI Q2 and the QIDI Box to collect waste filament, because I needed something that is slim and easy to remove. The attachment is very simple, you just need to unscrew the two existing M3 bolts and screw in…
Works best with inserting the lens itself into the model. Also you can attach the original VR Optician thing to it from the outside, however even on max distance I felt it touching my forehead. NOTE: The lenses had to be rotated a bit… so…
1-11-26 : Updated note about adding dab of superglue to tensioner ends. This ideally prevents the adjustment screw from puncturing when doing a lot of tensioning. Needs a re-design, but this works for the time being foe extra security.…
Poop chute for the q2 you will need supports for the nipples that go into the screw recess also you will need longer screws I used #4 5/8 pan screw from the hardware store
UPDATES 11/27/2025------------------------------------------ Changed the duct fins to center the airflow --------------------------------------------------------------------- No magnets are required and you can create any shape you want.…
The Qidi Box has very limited space to fit ø200mm spools. During my limited first use, I had no problem running cardboard Polymaker and Overture spools. But the cardboard does wear down over time and I thought "no problem, I will print…
Easy to print and assemble Quest 2 two piece adapter. Blade has thickness of 6mm so its ideal for use with rubber on both sides. Position Cloud code for right RH and left hand LH 262.107 BonWasySX-Q2 Printing instruction: Print handle in…
I have been using it for over a month now and am very satisfied. Features No original part replacement, easy installation Metal-free, fully 3D-printed PETG printable Only 2g, easy to print, no supports required Significant optimization:…
THIS IS NOT A JOKE! I strongly suggest you guys open up the back panel to check your Qidi Q2 machine first when you have recieved it. There is an assembling faulty which could happen on your Q2! By default, the toolhead cable in the back…
Description The stock model cooling fan duct sucks. Here I have redesigned one. The main purpose is to add air flow guiders so the cooling air could be more even and stronger. To maintain the dimension is important so it would not cause…
Let there be light! Simple led mount for Qidi Q2, angled at 45 degrees for optimal exposure. As you can see in attached pics there is waaay more light in the chamber now. Installation is super easy, just unbolt three screws in the front…
Expanded to full width
This is the "magic yellow box" from Qidi Q2 promos for printing on fabric. It's adapted for printing on Q2 (original model was made for printing on qidi plus4). This is V1. Qidi Q1 Pro bed is required (245x245), 4 rectangle magnets…
UPDATES 11/16/25 Added versions of both cooling ducts for the smaller 4.1-4.5mm wide heat inserts. This is a lightweight fan duct based off of my original cooling duct design for the Qidi Q2. The duct with both heat inserts and bolts…
A mount for up to 200mm long LED strips up to 12mm in width. Uses existing screws so no additional hardware needed other than the LED strip you are mounting to it. Simply remove the two screws existing on the upper right front corner…
UPDATES This is a compact and lightweight hotend fan bracket for the Qidi Q2. The brackets have ducts on them to help guide the air where it needs to go. There is two version available, one is for the stock 2510 fan that comes on the…
The original holder is hollow and doesn't provide rigidity under the weight of the spool. For improved rigidity, I also recommend making an insert to attach the spool holder to the printer's metal frame. You can download the insert model…
This is a poopBOX designed for the QIDI Q2. You need to purchase this to use it. https://ja.aliexpress.com/item/1005009650808509.html?spm=a2g0o.productlist.main.1.63ef5d8ffaQ6tJ&algo_pvid=9a851485-aca4-4130-9f65-4b1ba24d6ead&…
Material: PLA or PETG (PETG is better if the chute is close to hot parts) Layer Height: 0.2 mm Infill: 15% is enough Supports: No supports needed if printed vertically (standing up) Walls: 2 or 3 perimeters Installation Just slide it onto…
Update 30/08/2026 To complete the update started on 28/08/2026, I am adding to this project two sets of STEP files: 1- The QIDI design with the modifications needed to match the original ABS parts. These changes include my best guess for…
for qidi q2 with riser got the qidi💩box for my q2 and in the intial headache stage of getting this pos working right Unhappy with the stock cable chain clips and with hope of smoother filament changing i desinged this to help lift the…
only 63 grams of filament, fast printing - 1.2 hours, requires 4 magnets 5mm by 2mm.
It is used to install a 60mm board cooling fan. It makes less noise. It cools better.
Wanted a nice clean purge bin for my Q2, have added Qidi logos to make it look OEM. Printed mine in green hyper PETG, works really well with the purged filament making it's way around to the front easily. 2 walls 10% infill and it feels…
![[MORE EMBLEMS!!!] 1/4 Scale Federal Q2B Siren [BIKE BATTERY PACK!!!]](https://media.printables.com/media/prints/801fc401-0fd4-48b9-bf5f-726646484fca/images/13537966_0645e60b-61a8-420a-8f86-f0c0fb60ffb6_ee68b4ac-86d7-4417-8d1c-36218ee026cb/screenshot-2026-08-09-191803.png)
